Toyota :: No 4WD And Grinding In Front End
Feb 2, 2016
Was having fun in snow in 4WD hi on the dial setting. Doung donuts in parking lot. Heard a loud pop and then the vehicle would not go either forwards or in reverse. Turned dial to 2WD let it disengage from 4WD. Once in 2WD I was able to drive normally. After a while I tried to engage the 4WD again, placed in neutral turned dial to 4WD hi and then shifted to drive. Heard grinding coming from front end and vehicle still would not go forward or in reverse.
View 1 Replies
Advertisement
Had my wheel bearings replaced 3 weeks ago from a mechanic I never went to, as mine was on vacation. 3 days later tire fell off while driving. So we took it to my regular mechanic and had all safety issues fixed. New brakes, rotor, hub. But noticed that a grinding noise appeared. Took it back to mechanic, and he said that it was due to the spindle being slightly bent. Thst it wasnt a safety concerns, but will cause rotor/ brakes to wear out quicker.
I'd like to trust my mechanic, as he has always done good work for me in the past. But am a little shaky over every noise. I'd he correct?How soon should I get it repaired? I just dropped over $600 to get the can drivable again. So if I can push it off until I can afford it that would be great! Otherwise, I might need a small loan to repair.
View 7 Replies
I have an '04 Corolla with 206k with a slight grinding noise from the right front when I make a left turn. Is it the outer CV joint? The noise sounds like the tire is rubbing against a splash guard but it's not.
View 3 Replies
I recently brought my 2005 toyota corolla to my mechanic to give my car a check up as i will be going on a three week road trip soon.Upon assessment, my mechanic told me that my front right wheel bearing was making a strange noise and that i should replace it. I went ahead and had it replaced. after i had it replaced the front right wheel area was still making a grinding noise (louder than before it was replaced). I brought it back and he replaced it again with a new wheel bearing.
Again after the 2nd replacement it continued to make a load crunching, grinding noise when ever i brake the car. So once again, i brought it back. I thought perhaps it was my brake rotor and had him check that. He did just that and said the break was fine. He said it may be because the axl was not sitting true. so i had the axl replaced. well today i picked up the car and drove it approx 5 miles and the same crunching/grinding noise persists!!! I brought it back and it is once again being worked on. I need it fixed and am worried that my car won't hold up for my upcoming 4000mile road trip. I have attached a video clip of the sound to this post.
View 16 Replies
I have a 2007 Prius with 130,000 miles on it. I plan to trade in about a year, maybe a little less. I have noticed my brakes grabbing. My mechanic says that the front brakes are sort of grinding and the rear brakes are grabbing. Both are worn, the rear brakes to about 30%, front brakes to 60%. They also say they will probably last out the year. Should I put new brakes on to be safe and to be able to sell the car with new brakes, or should I just wait it out and trade it in with worn brakes?
View 6 Replies
My 2005 Camry started to make a, for a better work, "grinding" noise that appears to come from the left front side. It seems to appear around 40mph. Other symptoms:- the noise is not present when the car is in park even when revving up the engine- the noise appears to be correlated to the car/wheel speed - if placing the shift in neutral, the noise does not change while the speed doesn't change- if starting in 2nd gear, the noise only appears around 40mph when the engine is about 4500rpm.
Here it is a little hard to distinguish as the engine masks it- if switching the the 3rd gear, the noise does not change- if switching to "D", the noise does not change- coasting at neutral at more than 40mph still gives out the noise- when going over higher spots in the road (when the load of the wheels is reduced) the noise intensity goes down
There is no (or very low) noise at low speeds. Also, no noise when taking sharp turns. Had both front wheel bearings changed and the break pads, and the noise did not go away. I will be taking the car to a transmission place soon.
View 6 Replies
When on the highway, there is an occasional scraping/grinding almost a windy noise from the front left of the car. Happens most at high speeds when going over bumps. it's a Toyota matrix 2003 with 163k miles. We're on a car trip and are wondering if we need to address this now or if it can wait a few days.
View 2 Replies
I have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 Replies
Driving at hwy speeds and head a pop noise in front end. Stopped and couldn't find anything, heard it a couple of more times, still nothing found, now I have a grinding noise left front wheel. What the issue may be. 2001 Ford EX 4X4.
View 6 Replies
I have a 98 toyota 4runner. Limited, automatic transmission, 4wd, 6cly. 3.4L. Recently my 4runner was towed and after picking it up from the impound lot I went to test the 4wd. This model has a separate shifter for 4wd with an on the fly button which you press to engage 4hi. Well, when I went to test it the 4wd the light did not come on and I felt no "clunk" as I normally do when engaging the 4wd, (this is even after driving a few feet.) So I went to test the 4lo. I put the transmission in neutral and pushed the 4wd shifter forward to the neutral position as I tired to go one more to the 4lo position it began producing a horrible grinding sound. I didn't push the shifter all the way forward for fear of further damaging something so I went to put it back into 4hi and again this horrid grinding sound. Basically the 4runner was stuck with the transfer case in neutral? It wouldn't even go into park with out making this horrible sound, so I had to shut everything down and put it back into park and hi mode. When I turned it on again I tried it again and still the same result.The 4runner works just fine in 2wd. And eventually the 4wd light came on after driving a few blocks with the button pressed although, I'm not sure the 4wd was even engaged because I never felt the "clunk." It is still grinding when trying to shift into 4lo. Fluids are changed regularly and it is very well maintained. It has 228XXX miles.
View 3 Replies
My 2009 Toyota Corolla has started to make a grinding noise when starting. The sound is identical to when you try to start an idling car. What the problem is?
View 7 Replies
I have a 99 Toyota Tacoma 4 cylinder. Just reached 200,000 miles this past Sunday. I did a cold start this morning and there was a grinding, metallic noise from under the hood. I turned the key bafk because it didn't sound good. Turned the key again and it started like normal and ran fine. I had a new starter installed last Thursday and now I'm wondering where this noise is coming from. Before I changed my starter, I had the bad starter symptoms in the last two weeks, slow to crank over, the whining airplane noise (happened 3 times in the last 3 weeks). But now, this new grinding noise has me even more worried. Does my engine have to get used to the new starter and what other issues could this be? The battery passed the battery test at Autozone, and my alternator is fine as i unplugged the positive and negative wires from the battery while was truck was running. I really really like my truck and am trying everything in my power to keep it running as smoothly as possible.
View 19 Replies
I recently accidentally drove my Camry into curb in a parking lot. It was only a light, but since then I've noticed a grinding sound ONLY when turning right. Everything else seems fine. I looked under the car and saw the black plastic casing under the car is cracked and it looks like it might be grinding against the left tire, which could cause that noise. I've also heard it could be a bearing, but would that suddenly happen immediately after an encounter with a curb?
I do plan on taking it to the shop, but I have to wait at least a week until I get paid. I'm guessing that should be okay.
View 8 Replies
My 2000 Toyota Sienna has been making some concerning noises. It makes a periodic grinding noise, the period is related to the wheel speed...i.e. the noise happens once each time the wheel goes around. I can hear it while I drive, and it's even louder when I roll down the windows. The weird thing is that the noise stops when I hit either the breaks or the gas. First mechanic says that the wheel bearings are shot, and the second says they're fine. There is no "jet engine taking off" noise that I am told is typical of shot bearings, but there is a wump-wump-wump noise at higher speeds.
View 1 Replies
I replaced the pads and rotors on my 1989 toyota camry yesterday. Took it out for a test drive and all appeared to be OK. I did not bleed the brakes, but did have to remove a small amount of brake fluid after installing everything.
On my way into work this morning there was quite a bit of grinding noise coming from the brakes. The noise was not consistent, happening both while brakes were depressed and also when not in use. It also would go away after a few minutes and didn't always happen while braking.
I'm thinking the piston may be locking up at times, but don't know. I'll also throw out there that this is my first brake job. I did follow my Haynes manual and don't think I did anything wrong.
View 8 Replies
Lots of flooded roads yesterday, and I drove through a few deep water spots -- maybe 8"-10" mostly at VERY slow speeds. The car is a 2009 Toyota Matrix, standard transmission. It was pouring yesterday, and very loud so I don't know if the grinding noise started yesterday. Today when I first started it, I heard a grating/grinding noise in the front about in the middle. It sounds a bit like I'm dragging a large stick or a piece of metal under the car, but there is nothing dragging. I can be coasting, sitting still (but only when I first start it), accelerating, or braking. That said, it's not constant. It comes and goes as I'm accelerating. Once I get up to speed in 4th, I don't hear it. What it might be? Usually, I just hope that noises will go away. Do I need a mechanic to check it out?
View 7 Replies
We have a 1998 Toyota Corolla with 170k miles. The brakes are squeaking and grinding often. In Feb. the front brake pads were replaced, but the noises continued. In May, they replaced the front pads again, within a week the grinding and squeaking continued. Finally, I took the car in late July and had the mechanic drive the car around. He said the back brakes were making the "grinding" noise and the front was squeaking. He said it was "cheap brake parts". When he looked at the brakes he said the back brakes needed adjusting and may not be working as well, therefore making the front brakes work hard. This caused the front brakes to get hot and develop a glaze. He adjusted the back brakes and scratched up the front brakes. The car was fine for about 2 weeks or so. The sounds have gotten progressively worse and I refuse to drive the car. The brakes seem to work, but the sound is so terrible like something is loose, or off and scraping metal. We have used this mechanic for years with a recommendation from our neighbors.
View 4 Replies
I have 2009 corolla with 70000 miles on it. I replaced new brake pads. I have some metal grinding noise when i turn right only. I tried looking online and got few similar problem faced by other people. I am not sure if its exactly same issue. No accident damage. Mostly driven on freeway.
1) noise looks similar
2) I do not get noise when i accelerate
3) for car this old is it expected ?
View 5 Replies
I have a 2009 Toyota Camry with approx 124K miles on it (my daily commute isn't that great...). Lately I've noticed some vibrations or rubbing when I'm turning:
There is a constant rubbing/grinding noise when turning. It is more obvious when I turn right. It is definitely coming from the front tires. It does not sound like metal at all. Just like a rubbing noise, that causes a slight vibration up front.
When I'm driving straight, at a certain speed, I notice the vibration/rubbing sound, but it eventually blends in with the sound of the road. The ride isn't bumpy at all, so I don't think it's related to the struts. When I pull out of a parking place, turning left, it just feels "loose", if that makes any sense.
From what I've been reading, it seems to lean towards a bad wheel bearing, or CV issues. What the problem could be?
View 6 Replies
When I start my car (usually a cold start) I hear a TERRIBLE grinding-like noise. Other times it sounds like a shuffling noise. And then other times it's like its over-exerting itself trying to start up. I've taken it to the dealer many times as it's a 2014 Corolla. They have no answers. The claim it's just a characteristic of the car. I call bull. This isn't normal for any car. My car has a CVT transmission by the way. Could it be the starter? Spark plugs? Note: the noise is about 1000x worse in winter. Audio is attached in separate comment.
View 19 Replies
Just bought a 2010 Toyota Rav4 about 2 weeks ago. It rained the other day and the brakes made a grinding noise the first time I braked after starting the car but didn't make it after that. Did it again the same day, still raining, but only the first time I braked after starting the car. I have a 30 day guarantee on the vehicle and need to know quickly if the brakes are bad or not.
View 7 Replies
