Accent MC (2006-11) :: How To Properly Install A Timing Belt
May 20, 2016
Rebuilt a motor due to the timing belt failing. Everything works except I can't get the timing to line up perfectly.
From what I'm getting from the service manual, line the camshaft sprocket with the mark visible from the hole
Line up the crankshaft gear with the yellow mark at the bottom.
Do I have to do a double/triple turn of the cam/cranks to get TDC to be achieved properly? My biggest problem on this car is having the crank gear shift a couple teeth after tensioning the belt.
View 4 Replies
Advertisement
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
View 17 Replies
In the process of rebuilding a 2007 Accent where the timing belt broke while idling.
Pulled the head, ran a "water test" on the valves (put spark plug in, pour water on the valves and see if it comes out the exhaust/intake side) and found that only 2 intake valves were belt. Also shut off all the lights in a pitch black room, shined a flashlight in the intake/exhaust and didn't see any light leak from any of the cylinders except the one with the 2 bent valves.
Does this make sense? I would assume since 2 cylinders are always TDC at once, at least 4 valves would be bent.
Lastly, before rebuild I'll be replacing the 2 intake valves, all the valve stem seals, intake manifold gasket, exhaust manifold gasket, head gasket, head bolts and valve cover gasket. Anything else I should replace on the head? Trying to keep costs down as much as possible.
To add: Pistons have no damage on them, there are no marks of the valves hitting the pistons. The timing belt was replaced after it broke and the engine still ran however it ran rough. Compression test was done on only cylinder 1&2, 1 had 60 PSI and 2 had 0 PSI. Compression test was also done by just rotating the crank with a socket since I already had some of the engine disassembled.
View 4 Replies
I have a 2007 Accent with 119K on it.
I wanted to replace the water pump and I was wondering if this can be replaced without removing the timing belt or the lower timing belt cover?
View 8 Replies
The timing belt went out at idle while making a turn. I changed the timing belt, but when cranked you have to pump the gas to keep it running and it is really rough running with a smell of gas when you turn it off. On the last run it backfired slightly. There is no knocking or pinging. And have triple checked the timing. Could improper torque on the crankshaft bolt cause this or failed ignition coils?
View 21 Replies
I took my 1997 Honda Accord with 97,000 miles to the Honda dealer for a 90,000 mile service and changing of the timing belt. I also had them replace some gaskets, some other belts and the axles as they were not holding fluid. When I got the car back the second time I drove it the check engine light came on and the car will not shift gears properly. When I start the car cold, put it in drive and accelerate the engine revs for a few seconds before the gears will engage.
This continues whenever I stop and accelerate. It also happens whenever the car is ready to switch to a higher gear. The engine revs past 3000 rpm and then will shift a second or two later. The dealer says I need to change a rebuilt transmission. The Bluebook on the car is only about $3000. I'm having difficulty evaluating the best course of action. What is the reliability of a rebuilt transmission?
View 5 Replies
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies
I just changed the timing belt and everything runs great. I pushed the AC button and no light came on. I checked all the fuses and they are good I took the H and L caps of and tapped the pin and there was air blasting out. Don't know what it could be? All I did was loosen the compressor and remove the belt and put it back on.
View 2 Replies
I just finished replacing my timing belt, water pump and all belts. I made sure to double check the timing marks lined up via this pic:
Timing belt diagram
I put everything back together and no go. I am not sure what to do now. Should the crank sprocket pulley be in a special starting position? I see is has a "1" engraved on it.
View 22 Replies
My mechanic just did the timing bet, water pump and other belts. Also changed the tensioner.
Car runs fine and everything seems great until I get to a red light. The engine sounds louder then before. Not very loud but its louder and maybe a very slight vibration, not sure yet. No noises while driving, seems like its running the same or better then before. Runs fine though
View 4 Replies
Is there a "how to" on adjusting the tension of the timing belt in a 2002 accent 1.5L ....
View 1 Replies
Vehicle is an 08 Hyundai Accent 1.6L three door (hatchback) with 20,197 miles. This car was born on Oct. 16, 2007 and purchased in April of 2008. I told the owner to call the dealer and find out about when they should replace the timing belt as I had looked it up at the Gates site and found that it is an interference motor and also these Hyundai have some kind of lengthy warranty. When the tech or whoever she spoke to at the dealership asked about the mileage, they told her that she does not need to worry about the belt for about another five years, were rude and sounded inconvenienced by her calling. This leaves her with a bad taste in her mouth and more importantly, mis-informed.
I get the "Maintenance Log" out of the glove box and upon trying to decipher the timing belt interval, it states that the first course of action is an "inspection" at 30,000 miles or 24 months. How is a timing belt inspected? From what I have seen, a belt can look perfect today and snap tomorrow. But anyway, the next entry for severe service is replacement at 37,500 miles or 30 months which means this belt should have been replaced in October of 2010. Next entry is normal change at 60,000 miles or 48 months which puts us at April of 2012. After this it goes to 75,000 miles or 60 months.
I have already picked up the kit for changing the belt, tensioner, idler, and the two seals. How critical is it to change the spring as that was not included in the kit I got? I'm planning to do this job here in the next couple days as from what I can figure from the above log, It's way over due. I was reading some Hyundai forums and one stated that the 2011 model with the exact same engine calls for the first replacement due at 90,000 miles. How's this possible? Seems like these people (engineers) don't have all their stuff in one bag...
View 7 Replies
I bought a 02 accent base model hb 5 speed 109k miles for a winter car (have a mustang in garage.) It ran good until tonight when the timing belt snapped. I know this because while driving it made some ticking noises and then shut off and when you try to start it the noise that comes indicates no compression so the belt must've snapped and bent the valves.
View 3 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
I just put in a new water pump and timing belt on an 06 Camry with the 3.3L V6. After I was done the TCS light turned on and I don't know why. The light was never on before and the car is running very smooth.
View 2 Replies
I am deep into replacing the timing belt on my 08 Elantra 2.0, and am nervous about taking the tensioner off since it is not obvious how to set it. I could use a fool proof explanation on how to set the tensioner.
The Haynes manual talks about 1/4 deflection but that seems too imprecise.
I can not see the marks in the video : DIY 2008 Elantra timing belt video 2 of 2 - YouTube
And this post 2008 Elantra Timing Belt does not quite seem to explain. I am contemplating putting it all back together, just changing the accessory belts and handing it to a shop. I could use a fool proof explanation on how to set the tensioner.
View 7 Replies
How to change the timing belt and water pump on a 2006 2.0t passat?
View 3 Replies
I have a 2009 Elantra (automatic) that already has 52K miles on it. I drive a lot mostly at highway speeds. I know several people who recommend having the timing belt replaced BEFORE the warranty runs out at 60K miles.
The dealership has a 60K inspection where they "inspect" the timing belt (plus a whole lot of "fluff" checks, tire rotation etc) I'd rather just take it in and get it replaced. What should a timing belt replacement cost?
View 1 Replies
My girls family has had an 08 elantra 2.0 new since 2008 and I've been doing the work. I recently did the timing belt ( July) with beck arnley oem parts. 65000 miles. I replaced belt, idler, and tensioner.
Right after I did it there was a mild hum at idle. It somewhat did this before the belt so I assumed it was just the new belt in plus the very mild hum it already had.
Recently it is humming very loud and high Pitched. It gets louder with higher rpm. If I take the cover of and move the needle on the tensioner while it's running it quiets down a little but it's an auto tensioner and doesn't stay right where it needs to be AND even when it is at the ideal spot it still hums.
View 12 Replies
My car has 103000 miles on it and the timing belt was replaced several hundred miles ago. After the service I noticed it had a bit of a rough idle and a very slight sputtering noise, but still no check engine light. Was the timing belt put on wrong? The engine is non-interference, by the way.
View 1 Replies
