Camry :: 2002 V6 - ( P1135 Code) Air / Fuel Sensor Heater Circuit Response Malfunction
Feb 6, 2016
Just got a P1135 Code on the 1MZ-FE 2002 Camry.
My code reader pulls it up as (no typo below) : AirCFuel Sensor Heater Circuit Response Malfunction.
So I know it's a bad Air/Fuel sensor. Which one though? I replaced the rear sensor by the firewall about 6 months ago which fixed the check engine code (I don't remember the code). Would it make sense that the front one failed now or the back one failed again? Most of my research points me to a bad rear sensor however a lot of people also report that a code reader would report the sensor as "Bank 1 Sensor 1".
The rear sensor was replaced with a Denso 234-9042 Sensor.
I would play the replace and test game... however inspection is due within the month and after resetting the code, it usually takes about 50 miles to return. Being in college, 50 miles takes about 2 weeks.
View 4 Replies
Advertisement
So my 02 Camry V6 has the check engine light on. I had them scan at AutoZone. the codes that came up were P1130 and P1135. After reading some threads here, seems like it's the A/F sensor?
Just to confirm, there are two A/F sensors in the V6 model? I can see the front one easily but not the rear one. Need to identify which sensor needs replacement?
View 14 Replies
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
View 17 Replies
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 Replies
My 2002 camry 4cyl auto, jap built, with near 190k miles, check engine light just came on, P1135, has not replace any sensor since I own at 125k, 7 years ago, did noticed last 3 to 6 months, mileage drop to 25 or 26mpg average, used to be around 30+mpg, I thought it was change season for gasoline mix.
View 3 Replies
Got a 1996 Volkswagen Cabrio with around 125k miles. Recently the check engine light came on. Had the code pulled (P0133 02 Sensor Circuit Slow Response) and reset but it came back on shortly thereafter. I've also noticed that the car idles strangely, generally after it has warmed up a little bit. Basically it will idle rough and sound as though it might choke out but if you give it a little gas it goes back to a normal, even idle.
Right now it's getting around 20+ MPG average which seems a little low but I only purchased it 3 months ago so I don't have much to compare it against. One other thing I've noticed is that the plastic molding around where the gas nozzle goes in is cracked which makes it difficult to fill it up since it doesn't make a good seal unless you position the gas nozzle just right.
Any thoughts on whether either of these problems might be related to the weird idle? How hard is it to change the front 02 sensor?
View 1 Replies
SC430 came up with the check engine light, showing a "Oxygen Heater Circuit Malfunction", code P0155 (bank 2, sensor 1). Searching, I found out this is the oxygen sensor in the passenger side exhaust manifold.
My car is high mileage (over 130K), it's hard to justify purchasing a $230 sensor and paying for installation. My only goal is to keep the check engine light from turning on and passing state inspection/emission (the check engine light will prevent passing inspection/emission in my state).
View 12 Replies
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
View 2 Replies
This is what I get from the DTC .....
DTC P0705
Description : transmission range sensor circuit malfunction
State : History
I have done some google search on the above diagnostic trouble code P0705 and as i understood , it indicates that the Engine Control Module (ECM) has received an input error from the Transmission Range Sensor (TRS).
Since the check engine light illuminated two times (two separate occasion) then it turns off now; the ECM is actually receiving input signal from the TRS.
So that leads me to think that the TRS is actually working but the problem might be one of the following two:
1- Open or short in the TRS circuit?
2- Dirty transmission fluid.
What do you think the steps i should do first of all ? how would i check the transmission fluid since my vehicle has no transmission fluid dipstick. My driving condition would fall into "severe" category and it reached 60,000 miles now ...
View 10 Replies
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
View 14 Replies
I have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 Replies
I have 94 SE camry with the 3.0L V6 1MZ-FE engine and has individual coil packs. I'm getting a P1300 Igniter Circuit Malfunction. I have checked it out per the procedures EG2.pdf. I'm down to step 8 and the voltages are little different between the 6 points. started checking out the ground at the ECM per IN36 instructions. it appears that from pin #27 & 28 are not grounded to the ECU case.
View 5 Replies
1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...
View 5 Replies
Recently, my I4 XLE camry with abs came up with a cel P0500 - Vehicle Speed Sensor A Malfunction. Where the vehicle speed sensor is located? i doubt this thing's hard to service, but so far i have no luck finding it.
View 13 Replies
I have a 2002 Toyota Camry LE V6 with codes p1135 and p1155. Both sensors that are supposedly faulty have been replaced.
The new sensors are denso 234-9043 and 234-9047. I am confident that the second one was the right one replaced as both the new and the old had a little green marker(the location is near the firewall.) not 100% sure about the other one.
The sensors were brand new so I don't know what the problem is.
View 1 Replies
I was plowing and when I put it in reverse it felt like it slipped, but then the dash message trans malfunction came up. I checked the codes and I got P0722 output shaft speed sensor.
Code P0720 (oss) sensor circuit fault
Then the truck went into safe mods. Is it just the sensor or is my reverse going out...
View 4 Replies
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
View 3 Replies
I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 Replies
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
View 3 Replies
My 98 blazer (130k)recently started showing code p0740 tcc circuit malfunction..
The truck runs fine (except for the water pump I just blew) this is a tranny solenoid code. but my tranny seems to be shifting ok..
Is the solenoid easy and cheap enough to replace myself? I am trying to make up my mind if its time to start thinking of trading this blazer in on something with less miles or to fix it up and keep on trucking..
View 4 Replies
P0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
View 3 Replies
