Celica :: 1994 ST 1.8L Engine Cuts Off While Driving
Jan 7, 2013
I have a 1994 Celica 1.8L ST which cut off on me while driving. I have been trying to troubleshoot the problem. Here's what I've done so far:
Originally after the engine would cut off I could get it to start again, but there came a point when it wouldn't start. I ended up replacing the ignition coil, and immediately the car fired up again and was running. However, the check engine light was now on and the engine had far less power and was running very rough. Nevertheless, the car was still working and would no longer cut off. Thus, I took the car to Precision Auto Tune to get a diagnostic test done, and they told me the distributor was bad.
I then purchased a new distributor and replaced the old one. Immediately the check engine light disappeared so I took the car out for a test drive and it ran perfectly; yet, after ten minutes, the engine suddenly cut off while driving down the road. After coasting the car to a place to park, it refused to start again. I left it overnight, tried starting it the next day and it randomly started. It ran for 10 minutes again in park before cutting off again. Since then, i thought the new distributor was faulty and exchanged it for another, but the engine still cuts off after running and refuses to start again. However, when it refuses to start, if I install the old "faulty" distributor, the car starts without a problem, but the check engine light also appears.
View 3 Replies
Advertisement
I am having problems with my 94 Caprice. It will start right up when cold. After driving for awhile (not too long) then engine cuts off. Electric power is on but the engine is off (like it ran out of gas, or the gas was shut off). At first, it would take a few minutes for the engine to restart. Now that I have replaced the Fuel Pump Relay, it will start right back up, but when driving it still cuts off.
Could it be the ECM? Where is it located? Is it a "do-it-yourself" job?
What other problems might it be (besides the fuel pump)? Could it be the power distribution box under the hood? I also have fog lamps hooked up to the panel that wont work. The switch light comes on but the lamps do not. I am going to try to hook the (+) up to the battery and see if the lamps get power, if so, the box is fried (or the stud) But if the main power distribution wasnt working would the car still run, start? If the stud is damaged would it cause the gas to shut off?
View 14 Replies
1994 celica GT 2.2L
Just happened last night, i was driving on the highway when i noticed my temp needle was reading about a 1/4 of an inch higher than normal. That's never happened before. It's always been rock steady right in the middle. I was doing about 80 miles an hour. i slowed down to about 65 and the needle went back to the middle. I sped up to 70 and the needle went back up again. So i slowed down again and it went back down.
Tonight i was on the highway again, but due to the freezing rain and hail, i was doing between 40 and 60. Tonight the Gauge never moved from the middle. It was steady all the way until i got on the off ramp at the light, Then it went up and came back down by itself. I didn't hear the fans come on. I went to a local parking lot to do some tests. I parked the car (gauge was in the middle), and reved the engine to raise the temperature. It went up and then came down. Fans did not come on. Strange. I them went back to my house. parked the car, put the hood up and tried to make the fans some on. Here's where it gets interesting...
while in my drive way, the needle goes up, both fans come on high speed, needle drops. I then tried to do it again. Reved the engine for a second, i hear both fans come on high speed, but the needle is in the middle. It did the same thing again with the needle in middle again.
There are no external leaks. engine oil is full. Both fans work, but on high. There is no debris covering the radiator. I replaced the thermostat around april 2011,( it was not a genuine toyota part and didn't have jiggle valve. is that ok? it's been fine all this time.) Timing belt and water pump have not been replaced (so i've been told).
Tomorrow i will check the coolant in the radiator, ignition timing, and check the radiator cap. What are the odds of it being the cooling fan switch or a relay? i only ask because it hasn't come on low speed since this happened. Will warm car up in drive way and see tomorrow.
View 2 Replies
I have an F-150 with a 5.4L EFI and A/T. For the past two days while driving along the engine just cuts out. There is no chugging or sputtering. It just dies. When it happens, I place the trans in Neutral while still rolling along and it starts right up.
I had suspected it might have been a bad eec relay and connector that I had trouble with in the past, but I changed that all yesterday and the problem happened again today.
View 12 Replies
So, my brother has an 01' VW Jetta 2.8 VR6 with a 120k miles on it. He was recently driving around 50mph when the engine cut out, he lost all power and all the lights on the dash came on. He didn't get any loud bang when it happened, it just cut out. He tried to restart the car but heard the starter try and nothing else.
He got it towed to a garage who said they suspected it might be a timing chain but they couldn't say for sure until they started poking around. He doesn't recall getting the loud "marbles in an" noise when the chain is about to go. They were quoting around $4k to replace the engine. Being as my brother is a poor student this isn't something he can do, plus he'd already replaced the radiator, tires and all that and I want to verify what is wrong with it.
View 24 Replies
MT 2500 Where are you I've got a weird one. 99 Chevy 5.7 dully dump truck. The engine cuts out while driving at 3000rpms only. If you keep your foot in it it goes away at 3200. Does it in any gear(auto). Also, stopped and in park, it will do it at 4000rpms. Acts like a rev limiter. Fuel pressure does not change (60-62psi) when this happens, does it in open or closed loop. I disconnected the maf and no change. I've installed new cap, rotor, plugs, wires, coil, module(all original with 165K), no change. Runs sensational until 3K rpms.
View 14 Replies
Was just out and about today with my girlfriend and while driving back home, the engine just randomly cutout. I pulled over to the side of the road and popped the hood just to see if something came undone. Everything is kosher. Started it back up and carried on, but while driving the rpms kept dropping low and when stopped it would drop to about 450-500rpm.
So I put it in neutral and kept my foot on the gas to keep the engine up to about 1000-1500 RPM just so it wouldn't cutout. Drove part of the way home with overdrive off, even though speed limits in some areas won't let me even get into over drive. No check engine light, no messages on the message center, nothing. Looked into it and it seems to be one of several things.
Mass Air Flow sensor
Fuel Filter
Fuel Pump
Throttle Position Sensor
Yesterday I did fill up with gas, so maybe I got a there after they filled up the tanks. 2003 Merc. Mountaineer 4.6L.
View 14 Replies
Tonight while driving I heard a rattling noise under the engine, come to a stop and the engine cuts off. I pop the hood, get a jump and nothing. So I check the oil and it is dry... I changed it 4 months ago myself, it is a mystery how it leaked. No light came on, no oil leaks anywhere..
Is there any hope in having the engine turn over again? If so how should I go about trying to turn it? Engine only has 61000 miles on it.
View 119 Replies
I have a 92 Toyota GT...2 Door...2.2 liter engine...5 Speed ... It has just over 182,000 miles...ENGINE STRONG!
My Car has Been Cutting Off During Acceleration into 2nd Gear... At first I thought it was my battery post and the Grounded wire which was frayed, I replaced with New... problem persisted...I bought a new terminal for the Post...After Stopping and Going..
(When Car Cuts off...You can Crank it right up...No Problem...Began to accelerate and Cut off.. Start it...and go..Decide to Press Gas Down and ride the Clutch and Gas While Shifting and car Stays Cranked but I look like a Rookie Behind the Wheel and will Burn out My Clutch..So.. After I stopped and raised the Hood....I took the Negative Post Off...and Car Shut Off.. Bought a New Alternator...BAM...That's The Problem.. NOT!!..
4 Days later...Start out the parking lot...Car Cuts off..Same Problems All over again.. I took the Alternator to be checked..Fine..I took the Battery to be Checked and charged..Fine.. What Could Cause the Car To Cut Off after I hit 20 + Miles and Up..between Shifts....it Dies..? I need to Get to My New Job..and It's my only Means of Transportation...
View 7 Replies
My 1989 740 Turbo wagon cuts out while I'm driving. It only ever does it at about the point when the engine first reaches its normal operating temperature. It can cut out while idling or when driving at normal speed. I'm not sure if it's related to temperature or time (it usually cuts out at about the 5-8 minute mark), or if this is simply coincidental. It does it nearly every day.
It's definitely caused by the fuel pump relay cutting out. I've replaced this already, with no improvement. Something is causing the relay to suddenly lose an input.
Once cut, it takes a few quick flicks of the key to the START position for the fuel pump relay to receive power again. It will then drive faultlessly for the rest of the day. Although, if allowed to sit and cool for many hours, it will sometimes do this again.
View 7 Replies
1988 Bronco II - 2 days ago while driving my check-engine light came on for about 5 seconds, though there were no apparent drivability issues, then went away and did not come back for the remaining 20 or so miles home. Then yesterday while driving to a destination the engine cut out a few times. Gauges and such stayed illuminated but the engine lost power as if it wasn't getting fuel or spark. It occurred randomly over a 3 minute period: 1 second bogging, then 10 seconds powering, 3 bogging, 20 powering, 2 bogging... I depressed the clutch to check if the engine could idle and it stalled. Then I restarted the truck and drove 5 miles home with no issues or check engine light and even driving for a minute at WOT would not make the issue remanifest. I did not drive it today for fear of breaking down and I hope to get this solved before taking it on the road again.
I read the following codes:
KOEO: 11 (passes)
Continuous Memory: 22: Manifold Absolute Pressure (MAP) or BARO sensor out of range.
KOER: 11 (passes)
View 1 Replies
My car has been running kind of funny the last couple of weeks at which point I brought it to my mechanic twice. When I drive the car it seems that the gas is not getting to the engine and it bucks pretty violently around like 40-45 MPH initially and continues to bog down until the car dies. The engine light comes on. After waiting about 15 minutes it starts back up and drives okay for like the first ten minutes and continues to buck and then eventually die. First time they cleaned out the air flow sensor and changed the air filter and then they changed the cam shaft timing sensor or something like that and it continues to run terrible. It almost sounds like gas is not getting to the engine.
View 2 Replies
I bought my 1994 Accord LX new and am happy with it and the ~240K miles it has. Recently a very odd problem has emerged that is annoying...
Problem: The power to the radio cuts off now and then but only for a second. This of course always happens when I'm intensely listening to something like Car Talk. I first noticed it about 3 months ago while driving on the highway... whenever I tapped my brake peddle the radio would cut out. NOW the problem happens whenever it wants to...sometimes I go days without any problem, other times I can get a string of 5-10 failures right in a row and then it's "ok".
Here's the REALLY WEIRD thing... about 1:10 times when this happens BOTH the tachometer AND the speedometer cut out too! They drop to ZERO and then when the radio comes back on they pop back up to their proper readings... note nothing happens to the fuel or engine oil pressure gauges. The dashboard failures are what now have me worried.
What Have I done to address it? Nothing yet, not sure what to do... I cannot intentionally recreate the problem. Last time I took it to the mechanic for something else they looked at this but they couldn't recreate it. I'm afraid if I just ask someone to fix this it'll either cause a lot of hours to be racked up with no result or a lot of guesswork replacements.
View 14 Replies
Engine vibration? Its pretty significant and is always present doesn't matter if your in park or driving. What to check...
View 5 Replies
Volvo 940 1994 engine shuts off while driving?
View 1 Replies
1994 Explorer V6 100,000 miles, it is getting fuel and spark. After driving for a short/long period the engine will turn over but won't start. If you floor the gas pedal it will fire up, with a small puff of black smoke out the exhaust. Fuel pressure regulator came first to mind, and has been replaced. Problem was cured for a few days, then it started again.
Next Idle Air Control solenoid. Replaced, with same results. Replaced EGR position sensor. This worked for a few weeks. Then starting issue came back. Then I was told to replace fuel pump relay. This was the last part replaced. It had been running great. Started warm without any issues for a week. But now I have a check engine light and hot start problem again.
If the gas is floored the truck will fire. If gas is not floored the engine keeps turning and turning. I am sure it is not a fuel pump problem, as there gas fumes and the tailpipe is black. Could it be Mass AIR FLOW ?
View 3 Replies
I have a '94 Aztek that sounds like a small plane engine when driving. What is causing the noise?
View 10 Replies
94 celica GT 2.2 federal automatic, doesn't want to run, coughing, stalling, rpm gauge jumps eratically up down.
Computer says one code only, #12. Regarding Haynes manual it's distributor circuit or Igniter. When engine stops rotating (ignition still on), many times there is noise from distributor cap, like zzzzz....
System keeps shooting spark between distributor cap and rotor and there will be spark on that same spark plug !!!!!!
What's wrong? Distributor or Ignitor ??
View 2 Replies
My son has a 1994 Celica GT with the 2.2 5S-FE engine. Recently told me his heat didn't work very well, he had mentioned it last year but due to extreme cold we've been having I decided I would look at it for him. So anyway, I started by pulling the thermostat thinking it was probably stuck open or possibly someone had removed it completely, well there was one in there and it was closed so I tested it in boiling water, worked fine, replaced it anyway.
So then I checked behind and under the dash, thinking maybe something was opening or closing completely, but they are connected and operating, when I move the controls inside I can hear the doors moving and closing and all the linkages under the dash are connected and operating. Still no heat, so I figured the heater core was clogged since the return hose didn't seem to be getting hot, or the heater control valve was bad, pulled the heater core hoses, checked the heater control valve, control valve worked fine and was not plugged. Flushed the heater core, nice clean antifreeze, I then checked it with air, manual said put 6 psi on the input and make sure it was coming out of the return, which it was.
Reconnected everything, bled the air, still nothing, took the hoses off and connected the return hose to the heater control valve, bypassing the heater core, both hoses got hot. Sure seemed like a clogged heater core, did the air test again with 2 psi, still made its way out the return side. Reconnected everything again, still same issue, return hose never got hot. So while it was running hot with thermostat open, I removed the return hose, nothing coming out of the core, then I revved the engine and it started coming out, reconnected it and ran car at 3000 RPM, finally a little heat out of the vent, about 115 degrees by thermometer placed in vent, as soon as I let it idle the temp fell back to 80 within a minute or so.
Now I figured the water pump impeller was worn/corroded or was slipping on the shaft, so I pulled the whole thing apart. ( I should mention that the entire cooling system is very clean I don't see any corrosion anywhere) Any of you that have done this knows what a pain in the butt the whole job is, anyway, when I got it apart I was surprised to see that the impeller looked like new and was definitely NOT slipping on the shaft... what the heck???
When I took the pump off the housing I noticed the housing had a lot of wear, it look as if the previous owner let the water pump fail to the point that the bearing wore enough that the impeller ground down the raised boss inside the housing, I though AH-HA, this has got to be the problem, water is not actually pumping/circulating inside the pump as efficiently as it should, hence the reason I only get coolant into the heater core at high RPM. So i replaced the housing, the water pump, and while I was in there I did all the oil seals, and the timing belt. Well I got it all back together, fired it up added coolant, let the engine come up to temp, bled air, still NO HEAT!
View 8 Replies
Ok so i bought a 1994 celica GT from a police auction the other week and it wouldn't start so we went ahead and put a new fuel pump in it then we put new spark plugs in it. When removing the spark plugs i saw there was oil on them. My friend suggest we do a motor swap cause he thinks its a blown head gasket. Could this be an easy fix or should i go through with the swap?
View 5 Replies
I have a 94 gt with the 5sfe and at idle with the a/c on and up to operating temp the idle goes from 750 to 500 and cycles like that. It sounds like it is when the a/c compressor is cycling on and off but the compressor never disconnects the clutch unless I turn the a/c off. also when it drops in rpm the engine shakes bad. I have checked all the motor mounts and all are good and the rear one has a solid mount insert.
View 1 Replies
