Still P0303 code after: New spark plugs, new spark plug wiring, new coils, new injectors, full tune up. 99 Corolla 147,000 miles. What else could it be? o2 senor? or maybe intake manifold leak? valve leak? what am I missing?
View 1 RepliesThe issue with 99 Corolla CE with 147,000 miles....
I have a misfiring P0303 Code - Cylinder #3 Misfire. Here is what has been done in an effort to remedy the misfire. A major tune up, new spark plugs, new fuel injectors, new spark plug wiring, new coil packs, The car runs ok once warmed up but in the morning the engine vibrates until warm and also shivers a little while the car is stopped at a stop light. I have dropped it off at the mechanics a couple of times now to no avail. Once the code is reset it will not display the CEL for a couple of days but the symptoms still remains. The CEL comes back on within 2-3 days with the same code. Really frustrating! Well, at least this time CEL in not flashing like before it comes on and stays on.
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 Replies1999 ranger 2.5. 135k!So I started with a tune up all motorcraft, fuel filter and air filter. Did nothing! So I did compression check all cyc 150psi and above. So I did leakdown, had air leak at dip stick and valve cover, So I asumed head gasket. Pulled head and found 3 head bolts on passenger side had carbon deposit bluid up really bad, So replaced head gasket all surfaces clean and flat. Still didn't fix it!! My symptoms are better than before hd but still have a engine shake and flashing cel at 55 plus mph and p0303 pending! Coils tested good but going change them any way tonight!I'm stuck on this one checked everything 3 times and then again...
View 7 RepliesMy wife started our '99 Explorer last week and she said that the engine was rattling. I started it up when I got home and it sounded like something had let loose in the engine. We took it a local mechanic and he basically said that the motor was shot. I pulled the codes and it doesn't look good to me but I'm not a mechanic. Codes are:
P0301
P0302
P0303
P0173
I get this code, p171, every so often on my corolla. I have cleaned the MAF and finally changed it with one bought at AutoZone. I still get the code. What should I do next?
View 4 RepliesAfter a new distributor, check engine light coming on, getting a code 52, they (Toyota Dealership) replaced knock sensor. Unfortunately it seems to improve a little bit, but same issues happen; engine not running smooth at times. 94 Corolla. In the 223,000 mile club. 1.6
View 7 RepliesI've been getting a P0133 trouble code on my 2001 Toyota Corolla and am stumped as to what is causing it. I've ruled out the obvious stuff: I replaced the upstream O2 sensor and can vouch for the lack of exhaust leaks, since I replaced the entire exhaust system myself a few months back and checked again for leaks after getting the code a few weeks back. I haven't replaced the spark plugs yet (they're definitely overdue) or cleaned the MAF sensor (I've heard that these could be the culprits) and will probably do both this weekend.
View 3 RepliesRecently I have noticed that when on a tune other than stock I am getting a surge at idle - my RPMs drop to around 621-630 then shoot back up to 660-675. On my stock tune my RPMs stay around 640-667 and don't cause the surge (felt as a shimmy so to speak). Is there anything else that causes a similar symptom? I attribute it to tuning due to it only happening when running anything but stock but could be wrong.
View 2 RepliesI have a 2002 Toyota Corolla. On a hot day (the first in a while), I got a check engine light for P0125. I'm going to clear it and see if it comes back. I think it is a false alarm for insufficient engine coolant. If the code and check engine light come back, what should I do?
View 10 RepliesI've been chasing this P0171 code for over a year now. STFT is normal plus minus 5 but LTFT won't go below 21.1%. At highway speeds the lowest the LTFT will go is 10-15% then goes back up to 21.1% at idle.
Things I've done:-
- New the air intake gasket to the Orange one
- Cleaned the MAF sensor
- New PCV
- Smoke test reveal nothing (vacuum is at 21-24 in-Hg) (did not smoke test the exhaust yet)
- Changed to used fuel pump. Funny thing here is that now when I shift the car to park the STFT steady increases to 25%. The old fuel pump never done this. But the car feels like it has more power now.
- New gas cap
- Cleaned TB
- Cleaned fuel injectors and flow tested
- New A/F sensor and downstream O2 sensor
All parts were either genuine Toyota parts or OEM Denso. My next course of action is to buy a new Denso fuel pump or replace the ignition coil pack.
About two weeks ago, while driving on a hot, humid summer night, the check engine light in my 1998 Toyota Corolla came on. The following day, I took it into my mechanic, who plugged it in and came up with the code P0441 (Purge flow fault). He told me it was likely related to the fuel vapor canister, though I see this can also have to do with vacuum lines for the purge valve and canister or a bad purge valve itself. My gas cap was, and had been, tight, so it wasn't something as simple as that.
Reluctant to deal with this immediately, I went back to driving it, and lo and behold - the light went off after several days! Unfortunately, the light came BACK ON after several more. And most recently (a few days after coming on again), the light has now gone off!
Both times the light has gone off, the weather has been rather wet, but otherwise, there doesn't seem to be a clear pattern. What this on again off again pattern might say about the problem?
It keeps reading the code P0303 "cylinder 3 misfire". All coil packs, fuel injectors, spark plugs have been replaced. The exhuast smells normal. The oil is the correct color(maple syrup color, NOT milky). It's not blowing through coolant. Compression test came back normal. It's not the cat converter because the exhaust doesn't smell like rotten eggs. The car is sometimes hard to start. it hesitates/stumbles and shakes really bad. It feels like its not getting enough power.
View 10 RepliesI got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
I have searched but with no solid answer..
What I got - 04 Camry, 231K, never had issues, do all my maintenance myself, brakes, plugs, oil etc..
#3 Cyl misfire..
Possible causes
Plugs, - Has been about 2 years since I replaced
Coil - Bought car new in 04, never replaced
Cat - never gave it a second thought
fuel injector - put techron by Chevron just about every oil change, I know I missed one here and there..
burned exhaust valve - say it aint so...
poor compression - I have to rent a tool...
defective computer - I don't think so..
Went to do a few things this morning, started the car and it ran like crap. It was an obvious multi cylinder misfire. I checked to make sure all the coil connections and all other visible connectors were tight. Went back around and noticed the mil was flashing, so I shut it down and took the girl's car. I returned later in the afternoon and swapped out my intake in anticipation of it going to the dealer. Started up the car afterward and it ran fine without the mil lit. I had the codes pulled:
p0300 p0303 p0306 Its kind of weird that 2 coils would go at the same time. Do these cylinders share a coil or fuel injector driver off the ecm?
I have a 2003 Toyota Corolla, mileage app. 106,000. Check engine light first came on when driving to destination 40+ miles away (most of my driving is shorter, around-town trips). My mechanic said code is P0420 and so they reset it and said if it comes on again that I need a new cat converter. It did not come on until about 6 weeks later when I was on a longer trip again (had driven about 40-50 miles). Can you tell me if the P0420 code absolutely means that a new cat. conv. is needed or if it could possibly be a sensor or something else hopefully less costly than a new cc?
View 3 RepliesSo I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 Replies1997 chevy k1500 ... I have a misfire on cylinder 3 that i cannot figure out the cause. The idle is rough, backing out after starting is very rough, it seems to pick up at higher rpms but once the truck upshifrts to the next gear it shakes like a leaf in fall. within the past year the engine was rebuilt all new seals a new fuel pump, new injectors, new everything practically. so far i have done the following:
compression test results:125-130psi
fuel pressure test results: 50psi once primed, 50psi with engine running, no immediate pressure loss after engine is shut off
new spark plug wires
new spark plugs
replaced all four o2 sensors
So my 2001 5.3L truck has 206,648 miles on it. Over the years, it's been serviced every 5K with the only big repair being head gaskets which were done about a year ago.
Two weeks ago, I hit the gas to merge into traffic and the SES light started flashing and I could tell there was a miss. I got off the gas and a few moments later, the light went out and the miss was gone. I pulled the code and it was P0303 so I change the plugs, wires, and the coil pack for Cyl 3 fuel filter and ran a double dose of Sea Foam through the gas tank.
Bad news is I still have the problem. The truck drives fine; in fact, I pulled my bass boat 75 mile round trip yesterday. Everything is OK till you hit the gas hard to merge or to go up a big hill or pass someone. When you hit the gas hard, SES starts flashing and there is a miss. I also noticed the valves ping loudly when the SES is flashing. The only code it's giving me is P0303.
Could this be a bad injector not delivering enough fuel at higher RPM/under load? I was going to swap injectors and see if the miss moves. Any tips on popping those injectors out?