Ford 6.0L Power Stroke Diesel :: 2005 - Code P0299 Under Boost Condition
Sep 6, 2015
I'm having a little trouble with my 05 Excursion 6.0L .... We took off camping the other day pulling our 30' camper and the engine light came on pretty much as soon as we hit the highways. I checked my Dash boss and it came up as P0299 under boost condition. The truck never skipped a beat. The boost gauge never dropped and it seemed to have lots of power. Actually I've noticed too much boost while pulling. It's climbed up to 36psi before and was still climbing when I backed off the throttle. I'm thinking the turbo is fine but not sure what to check next.
View 7 Replies
Advertisement
Last night when I was towing my son's Ranger home - somebody stole all his gas & he thought the fuel pump quit - heard a pop and the truck started running like crap. Thought I had blown the CAC boot loose but that wasn't the case. As it turns out, the tube for the EBP sensor came off from the manifold.
I had taken it loose about a year ago to clean it out. I guess I didn't tighten it well enough. Truck blew black smoke, lost boost, and filled the cab with exhaust fumes. Easy enough fix, kind of hard to diagnose because that's not expected. Just throwing it out the for somebody's future search.
View 1 Replies
At 65 mph, egt was running between 1050-1150, turbo at 13-14 psi, rpm 2300. Code p0299 pops up. Before this the turbo would spool up to 28 psi going up hills. After it would not go over 16 and sounded funny. Truck is a 2005 excursion 4x4 with just under 200k miles . Trailer is about 10k pounds. No tuner. What do I need to be looking into? Is this too much for the truck to handle?
View 8 Replies
I just got back from a trip across the state to see the Miami boat show! Truck was running just fine on the trip over, EOT/ECT delta around 9* (seems a little high to me, Im hoping because im running 35's, but can someone back me up on this?)
On the trip back, cruising at 70, I noticed the check engine light went on... I didn't have it under heavy throttle or obscure circumstances... My ScanGauge 2 showed that I had a P0299, which as Ive read means something relating to underboost?
I cleared the code. And the CEL never showed again in the last 100 miles... Could this just be a quirk? Or should I be more worried about it?
View 14 Replies
Can a leaking Y Pipe throw a P0299? Dealership says that is my problem. My MAP at idle is 14.4 EBP is 17 - 18. At 60mph MAP is 20 EBP is 26-28. Boost is 10-20 .. Truck drives great no apparent issue. P0299 only code and appears when cold first start of day. If I clear it it goes away for the rest of the day and only comes back occasionally. Twice in 5 days only at cold start. 2005 F350, 100% stock, Ford filters all. Scan guage 2 for readings....
View 10 Replies
2011 Ford f350 6.7 diesel ... Is this a problem we need to have fixed?
View 2 Replies
I am fairly new to working on diesel engines. I was towing a camp trailer and got a P0299, Turbo Charger Underboost engine code. I never gotten any other codes other than this one when towing. I decided to pull the turbo and clean the vanes. Everything seemed to go back together good but now I hear what sounds like an air leak coming from the turbo area. The boots on the intercooler pipe are in good shape, I only loosened the clamps at the intercooler and the turbo. Left the boots on the pipe. I have tightened the clamps around the exhaust pipe connections with no change. I also seem to get a slower response from the turbo and possibly not as much psi as normal (according to dashboard gauge). I have driven the truck five or ten miles trying to work the turbo and have not gotten any engine codes to this point.
View 7 Replies
What to do 2011 F550 RampTruck 11,850 miles on it the vehicle has been back to the dealer 5 times for the same trouble code P0299. After the last time it was in they had it for 2 weeks seemed to be fixed. Last week one of my drivers was towing a Chevy S10 50 or so miles and heard a very faint ticking like a stone in the tire that got instantly worse and before he could pull over started rapping and stalled out. We towed it back to the dealer they removed the Cab disassembled the engine and found a "blown piston" is there quote. What should we do about this problem the dealer is supposedly fighting with Ford and Ford doesn't want to put in a new engine.They want to fix it instead....
View 12 Replies
Sudden power loss experienced. CEL (Check Engine Light came on) and Glow Plug Light was flashing. Power loss is severe so really can't drive it anywhere. Turbo Failed at 5500 miles.
Mechanic quote: "Found code P0299 for turbo power under boost. Removed upper engine cover and intake hose. Checked turbo shaft and found play near intake side of turbo. Removed lower engine shield and lower hose to intercooler. Checked for metal. Contacted VW and created VTA. Instructed by VW to replace turbo. Did."
Sounds like service manager abbreviated when entering into the computer. In any case a shame that this car was in the shop for more than a week while the dilly dallied and waited for a turbo to be shipped in.
Some earlier turbo-fail threads from last summer stated dealer told them "bad batch" of turbos was being experienced by VW. Believable, particularly if they're banged out in China? Let's all hope it was a bad batch.
View 1 Replies
Having trouble with this code. Replaced stock air filter with aFe filter 10,000 miles ago. 20,000 on truck. Threw code sunday dealer replaced filter with stock. said code may come back. which it did 5 miles later.
Edge CTS says max boost is at 22 psi. Is this something i will live with or indication of something else?
View 6 Replies
I've got an 05 EX 4x4 150k miles. Stock tune, EGR delete only ....
Driving along and everything was good plenty of boost no power issues. Got off the freeway and truck just stopped making boost. So I messed with it for a couple days. Cousin with a Mac scanner flaked on me so I was stuck using Edge gauge cluster and trying to trouble shoot.
NO CODES, No smoke, EGT's rise and truck seems like it is lean. Boost has fluctuated between 4psi to 11 psi. What should MAF be at idle?
ICP has been consistent with whatever boost levels were being made.
FICM 47.5
New MAP tube/nipple cleaned
New MAF
Clean Air filter
New fuel filters
VGT actuates
Accel ped in spec
Turbo spins free
New hot side CAC boots
View 8 Replies
P0237 code. The truck is a 2003 f250 with an edge evo . The truck will run great then throws this code and won't build boost of over 11 psi. Now it even drops it right off to 0. I replaced the map sensor a month ago and doesn't seem to have fixed anything.
View 2 Replies
Boost gauge is pegged and have no turbo don't know if the code has anything to do with the problem or not its a po6a7...
View 6 Replies
This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:
P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??
The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?
All my years of information on 6.0's was stolen with my laptop last year ....
View 13 Replies
I've been having issue with my truck lacking boost over the past month or so. The psi levels are normal in the morning when I start it up cold, the problem almost always occurs at start-up when the truck is somewhat warm and has been sitting for an hour or more after use. I've had boost levels at idle from -0.14psi to -0.56psi and as low as -1.2psi when driving as the problem is occurring, but it eventually kicks on and goes to normal levels after several minutes of driving. After originally taking the truck to a local diesel mechanic I was told it had EGR codes and they recommended installing an SCT tuner and cleaning the EGR valve to solve the problem. I had them install an SCT 5015 tuner and clean the valve but I've still been having the problems with boost.
View 2 Replies
My 05 excursion died on me a couple weeks ago. First it threw a p2290 code for low injection control pressure. It did this a few months ago and had no problems. Cleared code and did not come back until now. So I cleared the code. Drove a few more miles and lost all boost pressure. Still fires up and runs. It does run a bit rough but only a little bit.
I replaced the oil cooler, did egr delete, and put an IPR remote oil cooler and full flow coolant filter on it few months ago. Since it died i pulled the ipr valve and it looked good. I put a new screen o-rings, and wiring pigtail on it since it was out. Put back together and still no boost. I really did not figure that would fix the boost issue but i wanted to make sure the screen was not clogged or torn.
Truck will fire up cold and warm with no problem and run. The hose from the map sensor to manifold is good and i put new clamps on it.
2005 6.0 with 95,000 miles.
ICP duty cycle = 0.29
map kpa = 102
Injection control pressure = 5.91 MPA
View 14 Replies
So last night wife texts me pict of dash with CEL lit up... She was on the way home with horse in tow from a short haul to a nearby riding area. Truck has been in this service for more than a month and also sitting a lot. It has extremely low miles and wife tows horse with a soft pedal Always. I do try and take it out and exercise it, but that has been at least a couple months now.
Checked codes and ignoring a bunch of soft and repeat codes, got:
Current: P0299 - which is under/over boost usually, right?
Pending: P0478 - EBP high
So idled truck and all realtime info looked pretty normal, I think EBP was around 19, I realized I'm not watching Baro, I'll add that. Turbo was cleaned about 5K miles, but several years ago.
Was going to: clear codes, unhook trailer and take truck for a good drive, including some WOT romps and see what happens...? Or? I could set up data logging for boost, baro, ebp, rpm, and ?, prior to the drive... I guess eventually your "turn" comes up...
View 14 Replies
I have a 2011 F350 6.7 cclb 4wd dually. 212k ... I have the dtc p0284. The run good at idle and driving. I use it to pull a 40ft enclosed trailer. I have noticed that the boost gauge peaks at the half way mark and slowly drops half way down. I can feel my truck lose power when that happens. I also noticed that it runs alot better at night than the day. I have not modified anything except a s&b cold air intake. I have the #8injector replaced.
View 2 Replies
I just got a new 2006 E-350 van about 4 months a go (my previous 2004 got scraped - found out the fuel line leaving the secondary filter into the engine with clogged with bits of paper (wtf?)... after I decided salvaged it for parts for my new van...).
New van drives beautifully in the last 4 months without problem, but shut down on me on the highway yesterday. No strange noise or anything when it went out. I managed to coast safely to the side of the highway. Unfortunately, I cannot seem to start the truck again and had it towed home. It cranks, but doesn't start.
I have a scan gauge ii this time and it shows the following:
KOEO:
FICM ~48.5V
ICP 0
IPR 14.8%
Sync 0
Cranking:
FICM ~48.5V
ICP ~8PSI
IPR 84.7%
Sync 1
I still have a P0299 and P2262 check engine code from 2 days previous to the above, but this doesn't seem to be related to the no-start conditioning (both turbo related)
So, pretty much, I'm looking at a very low ICP. Some research indicates this is is due to a bad HPOP, bad STC fitting, or a massive leak. Given the really low ICP, can I rule out the STC fitting and leak? Looks like only the LPOP is providing pressure. Is there anyway to tell if the HPOP is dead or not once I remove it?
Anything I should shot-gun replace first? I have a bunch of salvaged parts from my old van in my garage, which doesn't include the HPOP unfortunately.
View 14 Replies
I've been having an intermittent problem with a no start condition when hot. It has lately gotten worse to the point that I was dead in the water for about 25 minutes while i had the hood open to allow things to cool off. I closed everything back up hit the key and it jumped to life just like it was new. I've read through the tech folder as well as several other threads regarding no starts but haven't run across anything that is pointing me in any one direction. It cranks over very strong on new interstate batts that are only 6 months old and the SGII shows sync on the FICM and I'm getting a good RPM signal showing about 160-170 cranking RPM.
Good logic power and showing 47.5 to the injectors. I'm running an atlas 40 from Ed in the FICM. I've wiggled wires and done a cursory look but I would think that if there was any chaffing that cooling off wouldn't affect it and it would be dead until fixed. Once it is running I have no problems, never let me down or quit on me while under way. Again, it is intermittent where I'll have 3 weeks or a month of no problem at all and then run into long crank times for another couple of weeks.
I've made no mods to any of the HP oil system and have no leaks that I can see, no consumption between oil changes. I'm in the middle of building a house right now and need the truck to be reliable. I'm pretty good with a wrench if I know what the problem is but I don't know where to start on this. It's an '06 model but an '05 build date on the motor.
View 1 Replies
Been working on a 2005 6.0 with 218kish miles on it. When I got the truck it had a contribution 2 code stored, no check engine light, just could see the code on the code reader.
Truck idled like crap, lacked power, so I replaced the injector. Truck improved but still had a miss, this time it had a stored code of injector 6.
Ordered another injector, got it installed today. Fired the truck up, ran perfectly, drove it around, absolutely 0 issues ran like a dream. Parked it for a few minutes before starting it again to wash it. Rough idle, not horrible, not noticeable. Cylinder 6 contribution code stored again, no check engine light.
So I drove it, I drove the hell out of it for about 15 minutes with the AC at full blast, WOT, etc etc. By the time I was done, truck was back to running smoothly.
Just walked outside after dinner to see if it would still perform well, or if it would idle poorly again, sure enough, 6 contribution, rough idle.
I just changed fuel filters with OEM, air filter is new. I just cleaned the EGR valve- although maybe it's not clean enough?? Oil change is tomorrow (had to wait for the filter to get shipped in).
I'm at a little bit of a loss on how to cure this miss, unless it's possibly an oil pressure issue from bad/old oil causing it?
View 12 Replies
