Ford 6.0L Power Stroke Diesel :: 2007 F250 - Wrench Light Came On While Driving On The Highway
May 20, 2015
2007 f250 6.0 .... I just had the wrench light come on while driving on the hwy. wasn't towing, or hauling anything. Just traveling around 70mph for an hour or so. I didn't notice any change in power. Got to my destination and cut the engine off. Couldn't pull any codes with an OBD II scanner. When I started it up again, light was gone. Owner's manual points to electronic throttle control, not much else.
View 14 Replies
Advertisement
I have ran 05 f250 and the wrench light keeps coming on mostly when I'm doing highway driving or when I go to pass someone. iv putt code readers on it(autoparts store readers and the good expensive ones)and i keep getting bad egr and some other codes but when I have the truck looked at everything is prefect I had a flush done on the truck and and it still comes on randomly . Could the fact that it needs an oil change cause the light to come on intermittently or is something else going on??
View 8 Replies
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
View 11 Replies
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 Replies
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 Replies
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 Replies
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 Replies
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 Replies
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
View 12 Replies
The thing is the truck seems to run fine. But, when it hits 30 pounds of boost it goes in to limp mode. Good way to get yourself run over on a highway. I'm wondering if the computer or whatever has gotten off somehow and is sensing a problem too early ? Would a re-flash possibly correct this ? BTW, it is a 2005 with 63,000 miles.
View 4 Replies
2006 F-250 6.0l,Auto, 175,xxx mi
When I turn the key to on, I hear the vacuum pump cycle (passenger side fender), but don't hear the glow plugs or injectors cycle. Glow plug light comes on and stays on for 30secs. Wrench light comes on initially, but goes off after 3 secs, but then comes back on after about 8-10 seconds. When the wrench light comes on, I hear a click under the dash and my cab lights go off.
When I turn the key to start, nothing happens. If I jump the starter, engine turns over, but doesn't start. I have check numerous fuses, disconnected the fan clutch, tried moving the shifting lever to neutral, wiggled wires around the FICM/PCM/GPCM with no success.
I tried checking for DTC codes, but my scanner (300 reader) doesn't get any power. I have checked my light, it has power.
Twice before, the truck failed to start like this, but after removing & inspecting fuses/relays (all were good), it started back up. Also, occasionally the truck would stall, (just like someone turned the key off), but would start right backup. But when it stalled, the glow plug light would illuminate for a second,then go off.
Own truck for 8 months, replaced the batteries & injectors 6 months ago. Very light puff of smoke when starting up otherwise ran well when shut off.
How to proceed? My first diesel so I may need some extra details.
View 11 Replies
I have a 2006 f250 6.0. the truck has 101k miles and to this point I have had zero issues. I am having trouble loosing power after running at highway speeds. Once I stop and begin to accelerate the truck looses power for a few seconds ,Belches smoke and begins to operate normally. I had an egr code, so I replaced egr and the problem persist. It is intermittent and does not happen if I stay under 50 mph.
View 12 Replies
So today I was driving down the highway and my engine shut off. No sputter or any thing I had just filled the tank. I tried to start it and it wouldn't start. It's been hitting a dead spot at around 3000 rpm like its not getting enough fuel or something. Right now I'm thinking it's an ipr valve but would like to know if what was the cause and how did you fix it...
View 10 Replies
Turbo is dead. I knew this day was coming. It died driving down the highway tonight at 55 MPH. Plenty of power since I left the office, all of a sudden the tone of the engine changed to a 6.0L and there was no power at my disposal.
Nursed it home keeping an eye on EGT's and let it soak while I ate supper.
Started it up, let it idle for a minute and tried a few revs but no boost and no turbo whistle.
Garage actually had a very slight haze to it after the test revs so something is broken.
DPF shouldn't be allowing any type of smoke to pass.
Bummer. Now I need a rental so I can get to the airport. Murphy's law has been in effect all day between software upgrades (IT stuff) and now my truck.
No CEL (this is shocking to me) but I found : P132B - Turbocharger/Supercharger Boost Control A Performance
View 14 Replies
I just got back from a trip across the state to see the Miami boat show! Truck was running just fine on the trip over, EOT/ECT delta around 9* (seems a little high to me, Im hoping because im running 35's, but can someone back me up on this?)
On the trip back, cruising at 70, I noticed the check engine light went on... I didn't have it under heavy throttle or obscure circumstances... My ScanGauge 2 showed that I had a P0299, which as Ive read means something relating to underboost?
I cleared the code. And the CEL never showed again in the last 100 miles... Could this just be a quirk? Or should I be more worried about it?
View 14 Replies
So I was driving down highway when I lost power. Engine was still running just had no power and would blow black smoke when I got on the accelerator. I pulled the EGR valve and noticed it had rocks stuck keeping the valve open. Cleaned it all up and put it back in. Went for test drive and seemed good again until few miles in same problem. Took it apart again and same thing.. rocks. I did this 3 times with same results...rocks getting stuck in my valve.
View 1 Replies
2006 f350 6.0..... I was driving for about 10 hours and truck ran fine. Until with no warning it just died. Got it towed home and now I try to start. It turns over fine but no fire.... I know not to use but we used starter fluid to see of it would fire thinking maybe file filter bit still no fire with the starter fluid. I find it weird that it won't fire even on stater fluid. The engine oil was very low as well but since topped it up.
View 14 Replies
2007 ford f250 .... 200k on it ....
Just had refurb engine installed with new oil elements as well. On a 9 hr road trip, the wrench light came on but no other warning lights.
No stock gauges showed any raises in levels.
No noticed loss of power at all.
The light would only come on once I drove at about 75 mph for about 10+ miles. It would not turn off when i slowed down, but when I would kill the truck and restart it, the light would be off. Just driving in town or on the highway briefly, nothing comes on. Took it in to oreillys to get scanned and they tell me a few codes pull up but none of them are valid. What would trigger the wrench?
View 7 Replies
Since day one my 2016 F250 occasionally has a reed sounding vibration at highways speeds near the passenger side occupant handle on the windshield pillar. Talked to a service advisor at the dealer about it, what it could be, so this must not be a common problem . The issue is intermittent and can not be reproduced on demand. I tried blowing compressed air all around the area of the Windshield to see if I could reproduce the sound in a shop setting, but no luck. Only thing in common with this noise is 75+ MPH during a rather windy day. I'm a little reluctant to drop it off at the dealer since intermittent problems are hard to diagnose.
YouTube...
View 10 Replies
2012 F250. 15k miles. It's intermittent, speed related, some sort of resonance or harmonic. WoooOOMMmm....woooOoMm, maybe every two seconds at 70 mph. Worn out tires once made a similar sound on a car I owned. This was severe inner wear on the rears. I'm not sure whether it's new or something I just never noticed; it's subtle.
View 3 Replies
I'm not near my stuff--is the battery cable terminal bolt 8mm?
View 14 Replies
