Ford 6.7L Power Stroke Diesel :: Oil Pressure Gauge Installation?
Oct 26, 2013
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
Oct 26, 2013
Advertisement
Ford 6.0L Power Stroke Diesel :: Coolant Pressure Gauge Installation?
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Installation Of Fuel Pressure Gauge?
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Pressure Gauge Installation
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure Gauge Showing No Pressure
Last week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
Ford 6.0L Power Stroke Diesel :: Oil Pressure Gauge Not Working
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Oil Pressure Gauge Says Zero?
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - When Cranking Low Oil Pressure Comes Up On The Gauge
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
Ford 6.0L Power Stroke Diesel :: Fuel Pressure Gauge Install
I finally received all the parts needed for installing my fuel pressure gauge, but I am wondering if I am going to need a schrader valve on my fuel pressure line going to the sending unit, or if I am going to be safe with just doing a 6 time cycle of the fuel pump like we do when we change out the fuel filters. Seems like that should work for getting the air out of the fuel lines, same concept I would think.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Fuel Pressure Gauge Dropped Down To 50 Then Back To 65 At 70 MPH
Well, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
Ford 6.0L Power Stroke Diesel :: Leaking Fuel Line To Pressure Gauge
Couple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Possible To Monitor Fuel Pressure With Gauge While Running?
OK so 2006 f550 6.0
If I want to monitor fuel pressure with a gauge in cab while running all the time... (not just testing) can I purchase one of the secondary fuel filter caps that have a port in the top and connect the sensor to this to run or is there a better way? (Or is that not going to work)
Cap I am talking about is something like this
[URL]
(I know this is a combo kit but they do sell the fuel only) But since it has a threaded port in the top I could connect the fuel pressure sensor to that and go from there correct? Would that give accurate readings?
Ford 6.0L Power Stroke Diesel :: 2004 - Fuel Pressure Gauge Is Reading Dead 0
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Fuel Level Back Light And Oil Pressure Gauge Out?
The backlight for my fuel level and oil pressure dash gauges are out. Would that require a simple bulb replacement or if there is something more difficult to replace, i.e. entire panel? The red needles illuminate, it's just the gauges themselves that are dark. The truck is my 05 Super Duty in the siggy.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Won't Start After IPR Installation?
So I installed a new IPR valve. Now it cranks but wont turn over. I read something about how the IPR valve has to be 'clocked" in the same exact position it was in when I took it out? Would this cause my truck not to turn over? Truck has never not started before.
When I tightened it down, it was not in exact position as the old one. If I wanted it in exact position as old one, it would have not been tightened correctly. I couldn't make one more full turn around. what do u think???
Ford 6.7L Power Stroke Diesel :: DVD Headrests Installation?
Installing the ford accessory dvd players for trucks? not sure if i want to get them just yet but i am looking into options since i have a sunroof and cannot install an overhead player..or can i? I just want to know what you have to do to install them? do they work good? does the leather match?
View 8 RepliesFord 6.0L Power Stroke Diesel :: Heater Hose Installation?
Had a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
Ford 6.7L Power Stroke Diesel :: Clearance Lights Installation?
I remember seeing a few people post about having them installed at the dealer for about 125-150 was this at the body shop or in the mechanic shop?
View 13 RepliesFord 6.0L Power Stroke Diesel :: Head Stud Installation?
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Ford 6.7L Power Stroke Diesel :: Low Tire Pressure Light On - TMS Pressure Low?
I had new nitto snows put on my truck and low tire pressure light is on.....Checked tire pressure 65 front and 80 back.....Started truck and screen said tms pressure low.....Hit ok and drove around on and off for 2 days now and cant get the light to go out......Is there some way to get the light out or do I have to go to my dealer to have it reset???
View 14 RepliesFord 6.7L Power Stroke Diesel :: Low Fuel Pressure And Reduced Pressure Limp Mode
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 Replies