2002 F350 7.3 intermittently wont start after I've shut it off, it runs fine but sometimes won't start when it's (warm)? Wait hour or more and it starts right up.
Is there something I can look for before I bring it to a mechanic?
Just to clarify I am a gal with little wrenching skills but I can look at videos and follow directions if it's not too involved.
I have an issue with my 2001 f350 7.3 PSD. Intermittently it will not start. It will crank really quick, but will not even try to start. I think it is not getting fuel. There are no CEL codes and I have a WTS light and the tach is moving while cranking. I hear a clicking/buzzing sound coming from under te center opf the dash. When I hear that sound it will not start. checked fuses and relays and it started before. not sure if removing the fue made whatever reset. this has happened a couple times. Now it will not reset. When I remove the number #24 fuse under the hood, the clicking stops. when i crank it, but still doesn't start. When it starts in runs perfect. Drained the batteries trying to trouble shoot, but have them charger now.
View 14 RepliesThis is an issue I started chasing after having all the injectors replaced on my aunt's F-350. We had them replaced due to hard/no start on cold (dealership told her they needed to be changed). Unfortunately, I did not get the buzz test results before changing the injectors.
So far that has been replaced:
Injectors
ICP (was leaking)
IPR
both UVCH
IDM (twice)
The issue we are having right now is that only 2 injectors (#6, #7) buzz properly. Initially when we changed the injectors, it did start but didn't seem to run quite right. We did the buzz test and at that time and injectors 1,3,5,6,7 would buzz strong but the rest were weak. After some forum lurking, we suspected that the IDM was faulty. We purchased a refurbished one and after we changed it, only injectors 6,7 would buzz strong. Thinking a faulty IDM was sent it back for a replacement. While waiting, we decided to put the old one back in figuring it would go back as it was before but only 6,7 would buzz strong. We receive the second IDM and same thing, only 6,7 buzz strong. We did a continuity test from the IDM connector and they all get 2.7 ohms (it was an older multimeter so not sure if being .1 under the 2.8-3.6 range is bad).
What I did next is use the uvch external pigtail to test the injectors. I plugged the extra pig tail into the uvch and then the ends of the wires into the plug of the upper harness. Afterwards, I would swap a different injector wire (on the pigtail) to the #6 injector wire (on the upper harness). Whatever injector that would go to #6 would fire correctly. So I know that the injectors themselves are fine. I am suspecting the wiring harnesses (upper/lower) but the continuity test would say otherwise. We also do not get any fault codes except for the EBP occasionally (waiting for a new one). I am lost on what to test or look at next.
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues. I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
View 2 RepliesI have an 02 crew cab SB 7.3L. The best way to I know to describe it is a sorta like a metal ringing noise. It just started this afternoon while pulling a 9k camper. It only does it under load. Boost stays the same and it happens in all ranges from 5psi to 15psi. It is intermittent. It sounds like it it coming from the turbo. I pulled off the boot and could not feel any play on the intake wheel.
After unhooking trailer and taking for a test drive I can not get it to do it again? The turbo was rebuilt about 4 years ago with a wicked wheel but has only seen about 18k miles since the rebuild. A quick look at the boots appear good but didn't get to take them off before going to work. I will try to post video.
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.
The past few weeks my truck has occasionally shown no signs of life when trying to start it. It goes through the "Wait to Start" routine and then when the key is turned ... nothing. No clicking, no cranking, nothing. All other electronics seem to work just fine.
This might happen only once ... or up to three times before it decides to crank. So far, it has eventually started on subsequent tries. When it does finally crank, it fires right away as usual and everything is as it should be and it runs great. No unusual smoke, noises or anything else.
This may be unrelated to the above issue but I noticed that lately once in a while, the back up sensors remained silent while I'm reversing and close to an object when I know they should have been beeping. (the audible override was not turned on either).
I may be grasping at straws here but would anything going wrong with the gear selector shifter cause both of these problems to surface? Like the lever isn't seating correctly and causing these issues? I also realize the two problems could be (and possibly are) totally unrelated.
I can live with the backup beeper not working but I can't survive with the truck being unreliable and not starting whenever it feels like it. It has newer, strong batteries and when it does crank, it's a "strong, fast" crank like normal.
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 RepliesI have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues.
I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
2002 F 350 7.3 4x4
Aftermarket gauge will climb to 250 after around town driving of an hour or so or multiple trips within the hour. Not towing. 160,000 miles on odometer. Changed trans fluid at 40,000 mile intervals. Most recently about 1500 miles ago. Most recent change using Mark K's method. Was getting fluid from rear port when I changed fluid. Blew out oil cooler and there did not seem to be a blockage as flow was sufficient.
Still overheating according to autometer trans gauge in test port. No codes retrieved using auto-ingenuity also O/ D light is not flashing. Would like to run torque converter slip test using AE according to wooden things method but TC slip desired and transmission gear ratio is not available under that name in live data meter. AE just updated to most recent version.
I purchased a new tranny oil bypass and will install soon. Also purchased a new 6.0 cooler to replace stocker but am hesitant to install if tranny is failing because I am concerned that the new cooler will just get some blockage from a potentially failing transmission and I will be buying a new cooler along with a BTS rebuild.
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues.
I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
I'm trying to figure out what axle I have on a 2002 f350 single wheel 4x4 so I can order a replacement seal. So this morning I got to work and noticed that am oily guild was dripping from the front of my rear differential where the drive shaft hooks into it. I figure it the seal, so when I went to look up the repair kit they list several different axle options because of gearing, what axle I have as there wasn't a in owners manual with the truck. Who can I find out what axle I have so I can buy the repair kit for it...
View 5 RepliesI finally got my 02 F350 running again after replacing the Fried PCM, but during some additional shop prep work, I discovered that the engine dies when you use the horn button, it will start right up afterwards so no permanent damage, but, Where to start? I have Forscan and a cable so I can get into the PCM but I need to know where to look or what PIDS I should be watching during troubleshooting.
View 6 RepliesI have an 02 F350 7.3 ... I just installed my glowshift tripple gauge pillar set. I have an EGT, Boost and fuel pressure gauge ... I followed all the constructions on installing them. The boost is working just fine and the EGT was too, but after a while the needle started going back and forth and the red warning light what blinking and then it just sat at 0 with the warning light on and stay that way. My fuel pressure gauge is connected to a sensore i put in my fuel filter housing, my fuel pressure gayge right from the start stayed at 30 psi with the red warning light on and just stays there .... Also the buttons to change the color and set the peak on the EGT gauge are sticking for some reason and staying down and aren't letting me change the color ...
View 12 RepliesI have a 2002 f350 7.3. It was running fine 2 days ago. After I put some diesel in it my water in fuel light came on. I drained the water out and took all the fuel out and put fresh diesel in it. It starts up fine and idles okay but when I try to drive it it looses all power and acts like it's starving for fuel and almost dies. It was smoking white smoke for a little bit even after I took all the water out but now it's black. What it could be.
View 9 RepliesI'm new to diesels and I've got a 2002 F-350 w/7.3L 224K miles. I've had it for about a year and had no problems. Burned a little oil, about a quart every 1000 miles or so, but in the last two weeks it's gone through the roof. I have gone through roughly 12 quarts in 300 miles. I see a lot of blue smoke at start up, and it's being harder and harder to start in the cold. From what I've read it could be several different things, and I plan on doing the CCV delete and changing the orings on the injectors just for good measure. Is there anything else that I might check as well, or am I completely off base on what it might be?
View 14 RepliesI have a 02 f350 4x4 6 SPD one of my transmission lines has went bad is there anywhere that sales them.
View 1 RepliesJust got myself a gently used Econoline E-350 7.3 Diesel and was loving it when she ran:
E-350 7.3 Diesel
Recently I have been having some charging issues. It started with it intermittently having a hard time to start, especially when it was warm. I carried a jump box with me and that always seemed to work. Then I noticed the voltmeter on the dash dropping. It went down to the 8 and I was like something is wrong.
Checked the battery voltage, it was at 9.6v. OK, maybe alternator isn't charging. Advance Auto tested the alternator, said it was bad. I replaced alternator. No difference. I pulled the battery and ran it on a conditioner to bring it up to proper voltage. It's now at 12.6v resting. Starts the van no problem. When running though the voltage doesn't increase to 13-14 volts like it should though telling me the alternator isn't doing it's job. Increasing engine RPM actually decreases voltage? Checked all the obvious things like bad grounds but everything seemed clean.
The only thing that was fishy was when I pulled the three way plug from the alternator, one of the pins had corrosion on it. I cleaned it up before installing the new alternator. I didn't do a diode test on the new alternator because I figured it was new, but hey maybe I got a lemon?
Anyway I'm going crazy trying to figure out where the problem is. All fuses are ok. Is there an external regulator or something I should be on the lookout for? Is there anything else that could be causing a non charging issue? The battery was manufactured in 2014 so it's relatively new.
And on a random note my ABS light is now on?
2002 F350 7.3 intermittently wont start after I've shut it off, it runs fine but sometimes won't start when it's (warm)? Wait hour or more and it starts right up.
View 2 RepliesI have a 1999 f350 with a 7.3l in it. A week ago I stopped at the pump and topped of my tank and when I went to restart it it it would crank and not fire. I had it towed and replaced the cam sensor with an aftermarket one. It ran but it would cut out when I got into the throttle and wouldn't start when hot. I bought another aftermarket one and it did the same thing. I tested the hpop pressure at the back of each head and everything checked out perfect while running. I replaced the Ipr with no luck.
And I also tried unplugging the icp sensor and it didn't make a difference. It starts perfect when cold but when it's hot and you shut if off it will just crank. I replaced the cam sensor once again with a ford one and everything worked perfect and it started no problem for a day then started doing the same thing again. I've taken a close look at all the wiring on the motor and it looks good. Battery's and starter are new. All the cylinder contributions test good as well as the injector buzz test. I'm not noticing any change in oil. Oil was changed 800 miles ago
I have an 02 f350 7.3 power stroke...Yesterday I noticed the outside temp was reading wrong,it was jumping from 67 to 86 to 92 back to 67..Temp was prob around 90 with high humidity and my a/c was on..So I got to where I was going and when I restarted my truck to go home the fuel gauge dropped to empty(I just fueled the day before) and fuel light came on and outside temp still wrong on the overhead digital display...Are these two things related???
Stopped the truck restarted it and fuel reads correctly again....Went out today and fuel light back on and on empty...Outside temp wrong again,a/c is on .....I disconnected the batteries when I got home to "reset the system"if there is such thing, fuel gauge working but outside temp wrong..?? Where is the outside temp sensor ?could condensation be running onto the sensor and throwing off my temp gauge? Just strange that both these things happened at the same time......I don't think its a fuse or they wouldn't work at all. I should mention all the other gauges work correctly...