I put a 150 w converter into one of my 12-watt power female and all of a sudden when i turned the engine on my check engine light came on with 4 glow plugs bad and now won't pass smog. any way i can turn off the check engine light so it won't comes up on the smog test?
View 3 RepliesI bought my 2000 7.3L Ex as salvage back in 2005. It had been through a driver side rollover and the seller had restored it. We lived in North Idaho then. But I remember I always had an issue with the check engine light being on. I don't remember what the codes said, but many mechanics read them and determined that nothing was wrong. Many surmised that someone had put a high performance chip in the computer and that was what was causing the check engine light to come on. All of them reset the computer and every time it would come back on. Should I replace the computer?
View 14 Replies1999 f250 7.3 101k California truck ... Scanned it said #1 glow plug did not clear the code. But now the check engine light is off again...
Questions : Harness issue ? Glow plug bad at 100k ? Glow plug controller ?
Start at glow plug work way back to GP CM or in reverse ?
Replacement Do all 8 or just the bank of 4 ?
Thoughts on replacement brands
Accurate diesel glow plug replacement kits any good, will they last ?
Or go factory glow plugs
What about Felpro gaskets
I heard about another brand of GP CM
2001 F350 290,000 no mods other than 6637, 2WD
Towed our new to us RV home last, only 15 miles from the dealer and yes its a big 5th for my truck at 12,000lbs. Anyhow, about 2 mins from home as I'm pulling off the freeway I got a SES light come up, then it disappeared. I checked codes this morning using forscan and nothing shows to indicate what it may be.
I was wondering if the transmission is getting hot if it throws an SES? It was only a short trip, but I have no real idea of the condition of the trans as the truck is new to us too - fluid looks and smells good.
Only new code is an ABS one c1229, c1233, C1234. I had 2 of them before - think the 1229 is the new one.
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
Now that I have been driving for a while I kept seeing this light come on/off and I did a video below - I don't generally flash my lights so don't think I am aggressive - but I wanted to make sure to capture the video and the light coming on.
I was thinking valve cover connection the 50 cent mod - and maybe it's all coincidental - but I did have to pressure wash the troph where the oil collects and maybe something else got knocked loose.
[URL] .....
I have a 2002 F250 4x4 Powerstroke with Automatic. I have been having off and on issues for months with the throttle going dead. This only happens when I start it, if it works when started it will continue working until a different start session.
I have replaced the pedal several times before learning how to check its output with a meter and am quite sure that is not my issue at this time. However, when the pedal is depressed the check engine light lites up and nothing happens.
I am thinking it must be the computer itself, but was told there is another sensor or module under the hood that could cause the issue also which is several hundred dollars to replace as would be the computer.
Is there a way to test the computer, and what is this other module/sensor if it exists that could be the issue? Unhooking and rehooking the battery to reset the computer is no longer working to buy me a few more weeks, is there a simple way to reset the computer to try?
I love this truck when the throttle works but I am getting tired of paying on a truck while having to borrow a vehicle to drive to work.
I have a 2000 f350 7.3 got a check engine light that turns off when rpms go up and a slow start. My mechanic said that there were no codes being blown, what is going on?
View 11 RepliesI have a 1999 f250 7.3 I was driving down the road today and I lost throttle along with my check engine light coming on. I pulled over and turned my truck off and now it will not fire back up.
View 6 RepliesI have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
2002 F350 7.3 PSD. 192k miles.
From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.
I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.
I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?
I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.
Truck started losing power then service engine light came on, drove about another mile then it just stalled ( almost home lees than a 1/4 mile). Got out open hood oil everywhere on top of motor. Looked under truck and oil all over the road. Looked back where I was driving a line of oil as far an I could see. Checked oil barely any on stick. Where should I start hpop or plug?
View 7 RepliesI need to move my 5th wheel which is in a trailer park at the moment. I went to take my truck to move it and the engine light came on and it seems to idle a little rough. I hooked up a code reader to the diagnostic port and it says no codes are found. I have a fuel pressure gauge, boost gauge, Exhaust gauge and they all seem to be fine, the original gauges in the dash all seem normal as well.
I have stage 1.5 injectors installed with a power hungry programmer and adrenaline HPOP. the truck sounds fine but vibrates pretty good when I try to drive it. I am also getting black exhaust smoke from the tail pipe when I gas it. This is new as it always ran really clean unless I was in the higher setting on the power hungry controller.
So to recap, idles rough, vibration while driving, engine light on with no codes when my code reader is plugged in, black smoke out of tail pipe.
Rob
So i replaced the faulty injector and the truck starts up great and runs great. The only issue is that now when i accelerate, the SES light comes on until i let it up a little. If i am at cruising speed or just a steady speed the light goes off. I havent checked for codes yet because the light didnt stay on. I have AE and know how to use most of it. Is there something i should be looking at? Could it have something to do with the Blue/Gray CPS i installed or maybe there could still be an air bubble in the oil rail from when i drained the rail ? I have a DP tuner and stage-1 injectors. Regardless it sure is nice to have my truck back out on the road. It was a horrible 3 weeks without it.
View 14 RepliesLight came on a few days ago. 2000 exc with 7.3 diesel the mileage report said 155000. Took it to Autozone a hour ago and these are the codes: P0683, P0676 and P1670.
View 14 RepliesA friend with a 2003 came to me Thursday. He has a dash light on that is an image of an engine. Sitting in the drivers seat, it is to his left. I do not recall seeing this image in my 2001. What might his problem be?
View 10 Repliesso got to work today, truck engine light comes on all foward motion stops. Just coasts and idles along. I have 280k on the orig stock trans. I also have dp tuner and did the valve body upgrade along with adding the 6.0 cooler hoping to extend the life of the trans. Reverse works. So i asume I am needinf a new trans. My options are Ford HDr4100 orig 4100, Or BTS built trans. I also pull a toy hauler as well. My question is If I order the BTS can I have a my local shop install it or does it need to be programmed at the dealer. If I get the HD from ford installed will I have to remove the dp tuner chip to get it programmed and also will i need another new valve body replacement.
View 14 RepliesThe SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
I have a 2001 F350 and my service engine soon light came on. For a while it went on and off and every time it came on the engine ran rough and I lost some power. I pulled the valve covers and checked the UCVH and everything was fine that I can tell I even made the shims out of quarters and put them in. After putting it all back together its still doing the same thing.
View 1 RepliesI was on the way back from the weekend trip and got a service engine soon light. I didn't notice any lack of power, rough idle or hard starting cold or hot. So we pushed on home. I checked the codes and it is the P1211.
Doing some research it seems the ICP is not as expected so I hooked up my phone with the Torque app and the IPR and ICP seem to be close to normal at idle and running. I din't see any high IPR %.
At idle the IPR was around 15.5 cold and 10.1 after a short run to the store and back when it warmed up a bit. ICP was around 690-720 cold and 470-490 when i got back.
Does that seem like normal readings? I cleared the codes and the CEL comes back on right away after starting the truck. I do have a TS performance chip that I will take out and see if that could be causing any problems. What else should I be looking into?
So apparently even though the engine light is coming on and off it's not recording any error codes.I tried with my reader, one from Auto one, and then a better one at a local shop, none of them would show anything. The issue is it feels jerky when the light comes on(or goes off). Imagine cutting your cruise control off while it's accelerating and then immediately cutting it back on and that's similar to what it feels like. What could be the cause? I guess I might drive my wife to work tomorrow so I can go by the dealership in Atwater Ca (I'm a bit worried, the one in Yuma, AZ tried to rip me off for three grand).
View 5 Replies