Ford 7.3L Power Stroke (1999-2003) :: Shut Off Suddenly Going Down The Road
Mar 23, 2016
Ok after rebuilding trans and being down a couple of weeks, I went on my 1st run since completing. Noticed when I started truck this morning it didn't turn over as fast as it was. 30 miles down the road Airbag Light comes on, and then volt meter dropped to 8 volts. Got stopped with truck still idling checked everything I had the tools to do so for. Decided to get back to my shop where I had tools, and 5 more miles and 55 mph truck just shuts off. Lost all power, truck would only click. Put my booster box on battery and gauges went back to normal but still wouldn't turn over but maybe once? Only place within a mile of my location was Walmart. Bought 2 new group 65 batteries, installed them and Shazam cranked right up no more problems. Short of the story bad batteries that checked Good with a load tester don't mean squat!
View 10 Replies
Advertisement
I am fairly new to powerstrokes, but have a general understanding how the 7.3l operates, and how the fuel system works.
The problem i am experiencing is a crank, no start. The truck has been great for the year and a half that i have owned it. Always cranked great and never any starting or running issues. One day upon cranking, i started the motor; it started normal running good for a minute until the motor suddenly started shuttering and then the motor shut off, happened rather quickly. The truck started up immediately after that and died....repeating the shutter until dead. Now the truck will not start.
Specs on truck:
2002 7.3l
230,000 miles
Manual transmission
Here's what i have replaced so far:
New parts include:
IPR (motorcraft)
ICP (motorcraft)
EBPV (napa)
CPS (napa)
IDM (reman)
Here are some of the diagnostic values i have collected during cranking: (FYI: i am a little confused on what the values mean and what they should be in order for the motor to start):
ICP: 2218 psi
ICP duty cycle: 41%
EBP: 265 kpa
battery voltage: 12.0
Rpm: 355
Things i have checked so far:
Oil is new and level is good.
WTS light cycles as normal.
Fuel bowl is full and over flows with cap off while cranking.
Fuel tank is above half.
Glow plug relay is good.
I was throwing a code for the PCM, but i removed the bully dog tuner and the code has since cleared.
HPOP oil is an inch below full.
I made a gauge set and dead headed HPOP yielding 1500psi.
Upon cranking i am seeing some smoke, i guess, but its kind of hard to tell from the drivers seat.
This is where i am at so far. I don't have a way to buzz test the injectors or tell if they are leaking past the orings. I have the valve covers removed, but i have been putting off pulling the injectors to replace the orings.
View 14 Replies
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
View 10 Replies
I have a late '99. It's been weak all summer. Took it to the dealership. They put it on the computer and said the only problem was bad injectors. Specifically #8. I replaced them all. It's still weak and now is starting to surge going down the road. I have my suspicions but I'm not a mechanic.
View 14 Replies
Here's the story. Truck has showed no signs of rough running. Wife drives truck around town. Truck up to temperature and doing fine on a 90 degree day. Stops at red light. Makes left turn engine light comes on truck seems to be running on 4 cylinders. Pulls over light goes off engine idles perfect. Pulls back on road light on no power. Gets truck to a local friends house lets it sit til I get off work.
I check for codes get p1316. Drive truck toward my house no problems for 4-5 miles then does the above with me. Limp it home. I know it is pointing at a wire problem to injectors and or IDM. Did a buzz test passed fine. Plan on pulling valve covers and looking for the usuall things. Any thing I am missing? What will a kOEO test tell me? Should I run one? How common is IDM to go out? One last thing just put a rebuilt transmission in it 3 days ago may be unrelated it seems to be doing fine.
2003 f-350 cc 7.3.
View 11 Replies
I was driving today and all of the sudden the dash went dark. No odometer, power windows, radio nothing. As soon as I touched the brakes it went dead. Wouldn't restart and all I could hear was a constant buzzing coming from the fuse panel by my knee. Let it sit for five or ten minutes then it would fire up and run good then do it all over again. The second time the truck had no power. I put a jump pack on it and fired right back up. After the the third time I called a toe truck. I'm guessing it is a electrical/charging issue.
View 4 Replies
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
View 1 Replies
I am a cummins owner who just got a 2002 7.3 last week. It drove great for 200 miles then suddenly died last night going 60 mph. It sat overnight then started up and drove 10 miles then died again. I changed the cps and still no start. I changed the oil and let it sit overnight and it started this morning and idled for 5 minutes then died again. I have tried unplugging the ipc and still same no start situation. I plan to check the hpop level today to verify it is full. I also checked the nut on the ipr and it's electrical connection.
I am just a shade tree at best and would love some direction on where to look. I don't have any scan equipment to check pressures. Am I correct in thinking it is a bad ipr?
View 13 Replies
Comming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.
Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer
View 14 Replies
Early 99 7.3 manual 6 speed. 224,000 miles. Truck starts great and runs great at idle. Starts out in gear just fine and seems to have plenty of power. It will act just like the key is turned off about a mile down the road. Will restart after extended cranking or letting it sit for 15 minutes or so. P1249, P0340, and P1280 codes pop up. Had a professional shop work on it and they changed out the CPS and IPC with factory parts. When i picked it up it had an SES light on but was running fairly well. When I looked under the hood the IPC had been cracked on the plastic part. Replaced it with another new one and it ran fine for 3 days, even pulling loaded hay trailer. Now when driving it, it cuts out for a second or two. It does that every couple miles until it stalls out completely. Restarts after 15 minutes and runs fine. Same codes are showing up.
View 3 Replies
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
View 11 Replies
A little about my truck. E99 F-350 crew cab long bed dually 4x4 223K miles. 4.10 gears with LS in rear.
I bought the truck June 2016. I ended up wrecking the truck on the test drive. Thought it was a 4 way stop and pulled out in front of a lady and she ran into the passenger side tire. Only damage that was on the truck was a busted tire, and the fender smashed in. Some how missed the door and the bumper.
I replaced all the front end: u-joints, ball joints, steering linkage, brakes, rotors, calipers, and all the u-joints in both of the drive shafts, also changed the fluid in both axles.
I have started to notice a slight "vibration" "shimmy" while driving down the road. Mainly while in a curve or changing lanes; applying pressure to the steering wheel one or the other. Tires have been balanced, and rotated several different times now with no luck at all.
While backing up, I can feel something "popping" "clunking" especially while turning. Like backing out of a parking space.
Insert troubleshooting:
Jack truck up and put on jack stands.
- Pull and shake all tires. --No movement
- Put in drive and watch all the rear end. --Nothing shaking or out of sync.
- Put truck in 4wd, hard to engage, watch front end. --Nothing shaking or out of sync.
- Turn tires to full lock. --Drive line starts clanking and shaking and rear tires acting funny.
- Turn tires straight. --Problem goes away.
- Put truck back in 2wd. --No problems when turning wheel lock to lock.
- Drive to empty parking lot. --Mainly feel problem while backing up, really have to feel for it. Most people call me insane.
- Lock the front axle. --No difference.
- Put in 4wd. Drive straight --No difference.
- In 4wd while turning. --Truck wants to act like it is fully locked in the rear and will bind up and slip a tire. You really have to give it some fuel to make it even try to move, and its almost like the truck wants to fold in half on itself. Cant keep the steering wheel in one spot as it keeps "jumping" on me.
- Put in 2wd. --Acts the same way until the truck fully comes out of 4wd then smooths back out to where you have to really feel for it. 4wd light stays on forever, before going off later in life.
- Put in 4low. --Gears grind and will not engage.
Would this indicate that the transfer case is messing up on me? Why would the rear axle feel like it is locked when in 4wd?
View 2 Replies
So on my way home today I lost all power, the engine shut of and i coasted to side of the road. Went to try and start, nothing. When key is in the crank position the gauges were jumping all over the place, also accompanied by a lot of clicking from behind the dash. Nothing happened when tried to crank. No power to windows or even emergency flashers.
So i get it towed home, and of course it turns over. But this only lasts about ten seconds, then dies. I could do that a few times and then back to no power at all. Even at times with the keys out of ignition it will still click and make a lot of noise.
View 14 Replies
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
View 11 Replies
Lately I had a couple glitches seemingly unrelated with this electrical system. Something just failed. I have two new motor craft batteries cleaned all wires/ clamps. The alternator has been tested good. The other morning I started my truck and smelt a wire burning up before I took off. Battery positive to glow plug relay was hot. The solenoid was junk so I replaced it. Still not the problem. With the battery positive hooked to the solenoid, truck will not shut off. It will shut off by key if the wire is unhooked. I do know this. When hooked up, the battery positive is feeding voltage (.4v) through a new solenoid to the PCM, thus keeping the pcm life when the key goes off. Bad pcm? With the battery positive hooked up to the glow plug solenoid. There is such a large draw that the charging system cannot keep up. Wich out me on The side of the interstate at 1 am as I watched my lights grow dimmer til truck stalled. U hooked the battery positive from solenoid got a jump and been fine since....however, there's a major problem lying there right?
View 8 Replies
My coolant bottle, as well as my entire engine compartment, is full of oil. The truck won't run. It will make ICP when I first crank it but then it goes away. I have the orings and gaskets to do the oil cooler, it is there any chance there's something else that caused this? Anyway to diagnose the oil cooler before I disassemble?
View 4 Replies
This started about 6 weeks ago. While sitting at a stop light the motor cut out. After some research I replaced the cps. Truck ran fine for about 3 weeks, then shut down again while pulling into the driveway of a store. Replaced the cps again (this time with a ford one). Ran fine for another 3 weeks, then shut down again on the freeway. No CEL on any occasion.
It's just like someone turned the key off. No rough idling at all. No smoke during starting or driving. When it shuts down, it will not start again for 20-30 minutes, no matter how many time you crank it. It will just turn over, no sputter. When it fires up again there is no air in the lines either, it runs like nothing happened.
I'm now thinking it might be a ipr issue...is there a way I can check myself or does it need to go to the mechanic? Or is it something completely different? This is my mother in laws daily driver, 178k. She does not drive on the freeway, 80% of the mileage is city driving. What could be going on?
View 12 Replies
Well a few days ago I pulled up to a gas station on my way to work for some coffee and since I leave for work before 6:30 AM my headlights were on. Well only the running lights were working. Well I shrug it off and later that night I come to the realization that both headlights weren't working. I tried the high beams and they do work. I also pulled both bulbs and both the filaments on each bulb seemed to be intact. What could cause this? I checked fuses 9 and 11 under the hood and they were both fine. I'm kinda at a loss right now.
View 9 Replies
I have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
View 2 Replies
I have a 99 F 250 7.3. It runs fine at idle even for a long time. When I drive around the block a couple of times it will start chugging and lose power and shut off. I have been mixing fryer oil with the diesel. I changed the fuel filter, oil change, crank sensor and fuel pump. I added 15 gallons of diesel and diesel treatment. Pulled fuel filter and bowel is full I'm not sure where to look next.
View 1 Replies
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 Replies
