I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Changing rear drum brakes to discs? I've done it with my 94 explorer, and i was wondering if the axles are the same, just swap the hardware like the explorers are.
View 14 RepliesI got a 2002 f150, right now it has a 9.75 with disc brakes. But it exploded. I can only find a 9.75 with drums in the wrecking yard. Can I just swap my disc brakes on to the axle with drums?
View 1 RepliesWhat would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 RepliesAfter putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 RepliesIm wanting to delete my abs brake system in my f150 2002 2wd all disc brakes.
I have to change the module with some kinda valve? and turn off the Abs in a tune?
I know the basics of a brake system, but im lost in the abs stuff.
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
I just replaced the front break pads. I didn't replace the rotors or get them machined, didn't look like they needed them. Once I pushed on the brakes (truck off) I noticed that brake fluid spilled out the brake reservoir. I'm guessing it happened when I compressed the piston into the caliper? I took some of the fluid out of the reservoir and now its at MAX (I didn't bleed them). I've only been only be able to stop and go on the driveway (I'm waiting on a new radius arm bracket). The brakes seems spongy, the brake hits the floor. ABS and Brake lights came on then turned off once I started to pump them when I turned the truck 'on'. Do I just need to actually drive and "break" the breaks in?
View 2 RepliesI have a 1998 f150 4x4 4.6 triton V8 regular cab, I would like to ditch the rear drum brakes in favor of disk brakes. is this an easy bolt on project? I do know that 2003 f150's had rear disk brakes and was wondering if i bought those parts if the procedure would be fairly easy. I know i would have to take a check valve out of the master cylinder to gain pressure to the rear.
View 8 RepliesI bought a 2012 Corolla S and I feel that the rear brakes are a little cheap. Has swapping brakes but how?
View 3 RepliesI recently bought a beater '89 F-150 (I-6, MT) with the following problems:
1) Both rear brakes seem to stick on occasion--almost like there was a "check valve" on the rear brake line. When that happens, there is a "BRAKE" and "Rear ABS" light (although the light does occasionally come on without brakes sticking noticeably).
What I noticed in Haynes is that the "RABS I" system functions in the following way: a) Upon noticing rear axle spinning slower than front axle, it actuates a valve, isolating the rear brakes b) If the problem persists, it then dumps the pressure back into the main system.
So, I wonder: Is this an ABS system acting up? If I were to (temporarily) de-power the ABS setup, would it default to "no ABS," or would I need to remove the hydraulic valves from the brake lines? (Don't really want to if I don't have to.)
2) You can select either fuel tank, get that tank's level to indicate on the fuel gauge...yet it only "draws" from the front tank.
Again, Haynes says there is a low pressure pump in each tank, feeding a high-pressure pump in essentially a small "header" tank. The "dual-function reservior" has a wholly mechanical selector, and notes that "Tank switching versus gauge conflicts can occur under certain failure mode conditions."
So: I can understand that the mechanical selector can, in effect, "stick" on one tank. But what I don't understand is how it can still draw from the front tank, with the "rear" tank selected (and presumably, that tank's low-pressure pump trying to feed the header tank.)
Is it possible that the low pressure pump--while beneficial to prevent gravitation at the main pump--isn't strictly necessary to fuel the engine? Or do I have a problem with a low pressure pump that's "always on," regardless of the selected tank?
I'm having a problem with my rear drum brakes locking up when I press the brake pedal. I've had this problem before, but ignored it because it wasn't too bad. It would just release after taking my foot off the brake pedal.
1998 F-150 XLT supercab 4x4 front discs, rear drums 4.6L v8 175k miles
I cleaned my master cylinder and bled all brake lines so they have fresh fluid. Now that my brakes work way better, my rears just lock up. I put new brake cylinders on, still locking up. I went to a junkyard today and replaced the proportional check valve, brakes still locking up.
Could I maybe have did something wrong when cleaning the master cylinder? I'm sure I put it back together correctly. Anything else i should look at? bad lines maybe?
I have 2002 f150 XL 4.6 L 2 wheel drive.Do i have rear discs?Need to change them not sure what to buy.
View 5 RepliesI have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesTwo months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 RepliesDrove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
My rear brakes lock up constantly. It doesn't matter how easy I am on the peddle. The ABS goes through it's test on start up. Afterwards, the light goes out. The vehicle sat for quite a long time. I pulled the rear drums and inspected for rust and brake shoe condition. There was no rust to be found and the shoes seemed to be in good shape. I've read on here about some shoes retaining moisture and causing the same thing. These 'seem' dry. I've also read that it could be the RABS. Is there any testing to determine if the RABS is definitely the problem other than by-passing it?
View 9 RepliesBefore I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
I've had this "rattle" when going over uneven roads for about the past few months and I think I narrowed it down to the rear calipers. They are both tight, but it seems as though the "floating" ability of the caliper is loose.....does that make any sense? I mean you can grab the caliper and it'll make a rattling noise, but the bolts are tight..
View 5 RepliesI recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
I have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.