I have a 2000 F250 PSD. When applying the brakes, the rear end starts jumping and bucking. The effect is exaggerated when pulling a trailer and applying the truck brakes to stop. The problem does not occur when manually applying the trailer brakes. It was suggested to me that this problem is caused by a hydro boost leak.
View 3 RepliesBefore I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
Rear steel brake line ruptured the other day (was pretty rusty). Despite being an idiot in regards to automotive repair (among many other things), I decided to give it a shot. I was able to get the damaged section off, went to Autozone with the broken piece, they matched it up, were nice enough to cut it and put on one larger fitting (because the two were different sizes) and flare it for me.
I was able to get the one side (at the T fitting) on OK. That was the "new" side, the one they flared at Autozone. Looks good. No leaks.
The stock side, at the passenger side caliper, leaks like crazy. Not out the threads, but out the hole through which the line passes. Know what I mean?
I'm having a hard time figuring out what's happening, because I'm not sure how this thing works. Does the line fit flush to something inside the connection at the caliper? Is it a bad flare?
It did not go in easy, but the new one was just as much trouble as the fitting that came out (stock?), so it must be right.
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 RepliesI have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
My 2003 F-250 5.4L 2WD has a front end vibration that starts around 40MPH (sometimes) and gets gradually worse until it goes away at 55 MPH. It oscillates the wheel a good 3/4"-1". It also does it also when decelerating through those speeds. It "feels" like the left side, but I can't be sure. When I jacked it up, I could get some movement laterally on the left wheel, but not the right. Also Noticed that the drive shaft has about 1/4" of play at the carrier bearing. Leaning towards ball joints.
View 2 RepliesAfter putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 Replies 92 F250 4x4 with 140,000 mi. Abs light came on, Replaced the sensor on the rear axle, Light is still on. When the light comes on the brakes still work but it takes more pedal to stop. Now the Brake light comes on, It has new pads on the front, and its bleed out good. When you drive it some times it works fine, then out of the blue it lights up.
I have checked the fluid level, parking brake switch, and even swapped the abs black box with another, also bleed the bleeder on the left frame rail. When the lights come on you can pull off the road and turn off the motor and restart the lights stay off for several brake applies, then sometimes they light back up. The light issue is not that bad to me but it drives my wife crazy. I am more concerned about it taking more/harder pedal to stop.
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 RepliesSo it looks like there is no adjustment on the Parking Brake on this ride other than adjusting the shoes up. As far as I can see my Parking Brake should work like a champ, but it won't hold on much of a hill. I have new shoes, new drums and it is adjusted up so I can hear them drag. I can actually feel it getting tight then looser as you spin the wheel, like one of the new drums is slightly out of round, so I don't think I could go much tighter. Is it possible one or more of the cables is stretched? I did see the shoes spread when I had the drums off and I stepped on the Park Brake, so I know things are working at least that much.
View 2 Replies2000 f250 with v10, got home from work today, then short time later we were going out again and my steering was extremely loose. Basically you could swing the wheel and it spins around. Power steering fluid was empty and I refilled it but still the same problem. Is there possibility that I'm just not using a thick enough power steering fluid?
View 1 RepliesI got my grandpa's 84 ford f250 its been sitting in the barn for awhile but i drove it over to my house yesterday and it drove fine but you did have to push on the brake quite a bit but not to bad but today after school i took it for a drive around the block and i noticed that when i was going down hill just coasting i was slowing down a lot and my foot was not on the brake but when i got home my breaks were smoking pretty good but tomorrow i was going to take the front breaks off (its only the front two disk breaks doing this) and clean all the rust off them and put a little oil on the piston on the caliper that pushes on the break pads...
View 1 RepliesI have a 10 inch lift and 37's on my excursion 2000 7.3l. I need to upgrade the breaks, the tires make it very hard to stop.
View 1 RepliesI was fueling up my 06 F-250 yesterday and smelled hot brakes. I checked and found the right rear was really hot. After it cooled down I was able to drive on home and it was not too hot when I got here. I was towing a trailer with my tractor on it so I had a pretty good load. It was over 6 miles to my house with stop and go traffic and no hang up. What should I do to keep this from happening again? I don't drive this truck much but when I need it, I need it to be dependable. It has 99k on the clock and is a gas job.
View 1 RepliesWhen depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 RepliesI have a 2005 F250 Power stroke w/ brake controller installed. There is no voltage to the trailer brake (blue wire) pin. I've checked all of the fuses and they appear to be okay.
View 5 Replies2000 Explorer 2WD. I had tons of front end issues that I have been working through. So far I have done upper control arms, upper and lower ball joints, tie rod ends, got an alignment. The steering/suspension system is in good shape now.
Now the only thing left is a scraping/grinding sound coming from the driver's side brakes. I mostly hear it at low speeds (taking off from lights, etc).
When I was doing all of the other work, I observed that the rotor is in great shape, brake pads look great. I am wondering if it is a caliper issue, maybe the caliper isn't releasing enough or something. What to check?
I have a 2000 F350 4X4 with a V10 under the hood and a 5 speed manual transmission. It has a heavy western hauler bed, and a dual tired rearend. The truck has disc brakes all the way around that work great. I bought the truck used and immediately replaced all the disc brake pads as well as the seperate parking brake shoes and I had the parking brake drums turned. My problem is the parking brake shoes won't hold the truck at all and never have even when they were new. The parking brake shoes seem very small to me for a truck this size and weight. I have adjusted them as tight as I can with out causing them to drag when they are released. Is this a common problem for this type of parking brake on this type of truck? Is there something I am over looking or need to do to perhaps improve the parking brake? Would it be possible to splice some sort of "locking" valve into the brake lines going to the disc brakes to perhaps hold them engaged when I park the truck? I have a good idea how air brakes work, so I suppose this "locking" valve would work like that except basically opposite of a locking air brake valve, if that makes any sense.
View 14 RepliesLast weekend I did a rear brake job on my 1997 F350 4wd diesel. I replaced the shoes, replaced all the hardware, replaced the cylinders and had the drums turned. I have driven the truck all week and everything has been fine. Tonight while out of town I set the parking brake to see if it was any better since the rebuild, and it was. Shortly after releasing the parking brake I drove about an hour to get home. When I arrived home by driver side rear brake, wheel, etc. was very hot. I threw water on it and it turned to steam instantly.
I suspect that setting my parking braked hard like I did (like you're suppose to) somehow caused it to drag. What is causing this and what needs to be done so that it doesn't happen again?
After reading some other posts I went out and checked my parking brake cable and found that it is not bound up that I can tell. Perhaps it did not completely release although it seems to release just like the other side. I checked it from front to equalizing bar and it is in great shape. The plastic coating is still on the wire and there isn't any corrosion the entire length. The only thing I did differently on this trip vs the one I made two days ago was try out the parking brake before I left. The last trip I could barely feel any heat on the rear wheels when I got home, this time the driver side was scorching hot.
I have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.