Ford - Explorer :: 1996 V6 - Transmission Engages Then Slips Right Back Out
Aug 16, 2013
'96 Explorer 4.0l V6 4X4... 214,000 miles. So, I'm having some transmission slippage and was wondering what can be done about it. You see the mileage and the only thing done to the trans was a drain and filter/fluid replacement at 120,000 miles.
Here's what's going on... When cold, in the morning, I put it in drive, trans engages, I move maybe 20 feet and it disengages. I wait up to 20-30 seconds and it engages and slips right back out. I wait, engages, move 50 feet and it disengages. You get the picture. After doing this 4-5 times it will engage and I can drive a 100 miles with no problem. Seems like it need to build up pressure or warm up before it will drive normally. I've checked the fluid and it is at the correct level. I guess my question is, would I be wasting time and money to replace the filter and fluid again or is it just warn out?
I've read when a trans starts slipping after it's warmed up means it needs a rebuild and mine is the opposite.
View 4 Replies
Advertisement
1996, f150, 300, 4x4, 5 speed, 296,000 miles... My pedal goes almost to the floor before the clutch engages and about a half inch, maby less, of travel back out the clutch disengages. I think it is about time for a new clutch. My question is what is the best clutch to put in my truck?
while i have the transmission slid back to replace the clutch i am planning on replacing the slave cylinder while im in there as well. Any particular brand better than the next on that item? Are there any other items that I should think about replacing while i have the transmission slid back to do the clutch?
View 4 Replies
I just recently bought a 96 XLT 4WD Aerostar. It's got about 158,000 miles on it. It's got a few problems I wanted to ask about.
1. When I'm on the highway, once I reach about 82 or 83mph the transmission seems to slip into neutral. Does fine around the city and every other speed on the highway but once I pass 82mph it slips and revs really high. Could it be the torque converter?
2. Clicking while turning sharp and reversing while turning. I figure it probably needs new cv joints?
3. The gas mileage seems terrible. I still have my Ford Econoline 250 and that seems to be getting better gas mileage. What might cause the mpg to be as bad as 12mpg on the highway?
4. The speedometer goes nuts after about 40mph. Is that an easy fix?
View 14 Replies
1996 F150 4x4 with 300/6 and M5OD mazda tranny. 145k miles on it and looking really clean, and just the truck we wanted. It used to be well cared for, but has been a bit neglected since the owner passed away.
I spent a few hours searching the forums here and didn't find anything matching my symptoms exactly so I thought I would just jump in a post, but if I missed a thread feel free to redirect me.
I've got a bit of a rattling noise as the clutch engages when taking off in first. Once the clutch is fully engaged it's quiet and it shifts well and smooth. Noise also occurs (but less so) if I don't match RPM's and ride the clutch into second or third. I don't think its engine noise from lugging or anything because it goes away as soon as the clutch is fully engaged or disengaged.
Changed the trans fluid last night and no different, Clutch fluid reservoir is full, clutch travel feels good, master cylinder looks good, (slave is hidden, but looks dry though dust cover) a little play in the white bushing that holds the clutch pedal bar in place, and the plastic pushrod that goes into the firewall, thinking about replacing this linkage.
I work on big diesels for a living so i'm not scared of getting greasy. I'm almost inclined to think someone did a clutch job without resurfacing the flywheel. Is there an improved replacement for the pedal bracket and linkage? I don't mind just doing the clutch, but I don't want to be throwing my money away.
View 4 Replies
My wifes 04 explorer 4.0 4x4 slips in between second and third gear and you cannot manually shift the gearshift below 3rd gear. I assumed tranny was going out but was told that it could be the transmission control solenoid or the transmission control switch (i think they are the same thing). I read that the most common symptom of this going bad is a slip between second and third gear. Haven't checked codes but will when i get home to see what it comes up with. This is the messed up model where you have to add fluid underneath through the drain plug. Was going to change fluid and add lucas to it to see if it remedies the problem.
View 1 Replies
I have a 2002 Ford Escape 4x4Automatic with 97K on it. It has just started slipping in Drive. It will go in reverse just fine. If i put it into 2 or 1 it will take right off then I can move it into D but only with the OD off. If it is on the engine revs and you don't go anywhere. I have no lights flashing or bells going off. The fluid is clean and doesn't smell burned. Is my transmission toast? Is there a chance I can have it fixed cheaply or even do it myself?
Here are the symptoms once again.
Moves in Reverse.
Revs in D with OD on or off
Moves in 1 or 2 with OD on or off
When you get it moving you can put it into D with OD off and get 3rd gear. If OD is on It just revs.
When you come to a stop in D with the OD off and try to take off again it just revs. You have to use 1 or 2 to get moving again.
Will the car make it 300miles home so i can have it looked at?
View 5 Replies
I have a '96 Dodge Ram 1500. The only way I can describe the problem is when I go around 75, it feels like it loses power for a split second, then recovers. It will do this repeatedly, until I slow down a bit, then it won't do it at all. But once I speed up it will do it again. My first thought was the distributor/cap.
View 7 Replies
In a matter of weeks, my truck destroyed two sets of flywheels and starters. When the ignition key engages, the engine "jumps back?. Apparently, this causes the starter and flywheel teeth to grind. My mechanic cannot determine the cause of the "jump back". He thought that it might be the timing. His examination and testing, however, proved the engine properly timed.
View 6 Replies
When my Excursion sits for a while, the transmission slips a lot at first till it builds up pressure. Is this a problem? It seem fine other than this.
View 12 Replies
Looking for a pic or diagram or able to explain it well, of how the valve body engages the shift linkage/kickdown on a c6. I need a pic of the actual valve body itself and how it engages INSIDE the pan NOT externally.
View 14 Replies
I have a 2008 Ford Lariat F150 with 53k miles. The transmission seems like it slips at times. Here's the scenario. When I take off from a standstill and going through the gears at a normal acceleration pace, say I momentarily lighten the acceleration pace then try to resume. At that point, the transmission seems to slip momentarily, then bumps back into the pull mode. It feels like there is slack in the drivetrain until it re-engages, or like the lockup torque converter momentarily releases until the computer has time to react to the accelerator positioner calling for more. One guy said the transmission is, at that point, between two gears... either trying to decide to downshift or to upshift, but you can feel the surge in rpm momentarily until it decides ... then bump and your off and running again. If I push the O/D button, it stops doing it. What I can do? Because the dealer can't seem to get it to act up when they test drive it. It does it fairly regularly on me though.
View 4 Replies
My 94 e4od does a few things. It doesn't seem to engage positively all the time. It doesn't grab well in manual 1st, but does in D. I had the FIPL reset at the dealership and he said he never saw a FIPL needing to be set so far one way. Also it has overheated a few times. Either the TC doesn't lock up correctly or its just not all the way in gear (if thats possible) I changed the fluid but it did it again recently.
Also the speedometer is jumping around like a nut case, the abs light is on...sometimes, when I have the headlights on and put my right turn signal on it feels like the TC locks up. Oh, yeah the lights are all jacked up in the back. The left turn signal light also has a small amount of voltage when I put the headlamps on (my test light lights up dimly) I thought it might be the multi function switch so I removed that and cleaned the connections. Nothing changed but I dont think that was it. I have troubleshoot this all day and I don't have too much of a clue to whats going on.
View 4 Replies
My 2005 4.2 L transmission slips in overdrive but I turn off overdrive and it stops slipping instantly. What could be the reason for this does this require an entire trans rebuild or is it an easy fix.
View 1 Replies
i have a 97 mountaineer v8 aod,for the last 2 winters transmission slips when cold out on the highway, only when temp outside gets 30 or colder, pull over let it run 5-10 min runs great at 65 for about 8-10 miles then same thing, I put new filters twice and new fluid,i have put over 40,000 miles on it since it started doing this, it doesn't do this in the summer...
View 6 Replies
I have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 Replies
I have a 2004 XLT supercrew 4x4 with about 150,000 miles with the 5.4 motor. I noticed that when entering an interstate at around 50-55 mph it feels like the tranny slips. There is a jerk, jerk, jerk than it stops, it doesn't do it at any other speeds and only getting on interstates. Runs fine in town. No lights on the dash or codes, fluid level is normal and clean. I did have a caliper sticking but it was replaced and it's still doing the jerk, jerk, jerk. Could it be U joints?
View 6 Replies
finding out what is wrong with my Taurus. I have searched all over the internet not finding any posts about a similar problem. When driving after I turn past a certain point only to the left not to the right. The car slips into neutral revving, then once Ive straitened out somewhere along the wheel turning radius it re-engages in gear and lurches forward. The car drives fine and shifts smoothly except this.
View 3 Replies
I have a 78 f100 2wd, 300 inline 6 and I've put 2 c6 transmissions in it. The transmission shakes real bad in reverse. When you put it in drive and try to take off it wants to quit pulling but when you put it in first gear and shift up to 2nd it works perfect. My plan was to just junk the C6 and switch to a manual trans but I don't know what trans I would swap it with.
View 8 Replies
The C6 in my truck is acting odd.. its into drive by 17 to 21mph under light throttle and under moderate throttle it slips occasionally when shifting, the 460 had a fuel spurting motorcraft on it, had to swap that for an edelbrock 1406 to drive it. The kickdown is there but setup for another truck. I don't know if the c6 has a vacume modulator or if its all controlled through the kickdown rod.. it does need a fluid an filter change that's gonna happen this week.. this trans just has me leery with the soft shifts.. its in 2nd almost immediately after takeoff....
View 6 Replies
2000 Ranger XLT 4x4 3.0L Auto
So a couple months ago I had a transmission problem. It shifts high and hard all times and after the "od" light gets going (after it gets warm), the transmission slips (like riding clutch) when starting from a stop. If I went from drive to 1st gear with the selector and back, it cleared the slipping problem for a bit. I did an oil/filter change and about 50 miles later the truck is running fine, no issues. One day I hopped in it to go to work and it was like nothing ever happened. Fast forward 1,500 miles later. I start to notice the transmission is subtly shifting weird, like a small jerk when shifting. It gets worse over 50 miles and now I am back to the above problem. Is there a way this could be a sensor or solenoid problem? I never heard of a transmission correcting an issue then starting at it again so much later.
I don't like fixing or working on an issue unless I am at least 95% sure what the problem is. I also don't have $2k to plop down on a repair at the moment. Would it be worth it to take this to a dealership and see what trouble codes I am getting? I would try a transmission shop but it's not guaranteed they will have the test equipment to check a ford transmission. Also a friend said that AutoZone and other stores can't check transmission codes. So what's the best option here?
View 14 Replies
2006 f150 4x4 4R75E trans slipping in forward gears, reverse is ok. I dropped pan and it was clean. I dropped valve body and found OD servo shaft clip broken, the large snapring was I fine and in place. It allowed the inner shaft to float up and down. Would this cause my forward gears to slip or do I have a bigger problem?
View 14 Replies
