Ford F-150 - 1997-2003 :: 1998 V8 - Check Engine Light Began To Flash
Mar 12, 2013
I own a 1998 ford f150 4.6l triton v8. I was leaving my house to go on a snowboarding trip about three weeks ago it was a rather warm wet day and all of the sudden my check engine light began to flash. I immediately pulled over and restarted my truck, once it was started again it was solid.
I turned around and started driving towards home. I get a small amount of feedback from my speakers and usually it's a smooth whizzing sound but as i accelerated the sound began to stutter rather than remain smooth. after about 5 minutes of driving this went away and the check engine light remained on.
so today I went out it's also a wet day and it's raining quite a lot. on my way into town everything seemed okay. then on my way home the check engine light began to flash again and the feedback from the speakers became choppy again.
I would also like to mention my battery light is on but it was on prior to the first time this happened. I'm just wondering if the belt could be loose or slipping due to the wet weather?
View 2 Replies
Advertisement
My 1998 Toyota Corolla has 180 K miles. Two days ago I was putting the pedal down to get to work on time and it bucked, began chugging like a motorcycle and the check engine light (which was already on because of an emissions issue) began to flash. A mechanic looked at it and saw that cylinder 3 wasn't sparking. He changed the plugs and wires but the engine was still chugging, especially when idling. The mechanic decided it was a stuck or burnt valve because he said he could hear/feel a lack of compression in the cylinder. I'm looking for a second opinion on the issue, and a first opinion on the mechanic!
View 5 Replies
'98 F-150 4X4 XLT began squeaking recently. Have 1/2 mile long sand & limerock driveway thru mature North Florida jungle & every root'n'bump makes it squeak.
Was certain it had to be the J.C.Whitney/Owen's running board I left on passenger side. Upon close inspection, wrestling with it & popping it with big rubber mallet was surprised to find it tight & silent.
Checked bumper & associated bolts, then exhaust & everything else I could see/touch sliding under on a moving quilt.
Does not sound like bushing or ball joint. High pitch squeak, up near the annoying frequency of nails on chalk board.
View 11 Replies
It is a 1997 Ford f150 5.4 4x4 extended cab 175k miles. Took a 600 mile trip, first 300 no problems, then the "od" light began flashing, the truck shifted fine so I kept going, drove for about a 100 miles then stopped for fuel and read the code, (p1728) cleared the code and drove another 200 miles, no light no problem. The whole time there was no drivability issues. Yesterday I drove all over town, stop and go traffic, locking the TC and it would also unlock, no problems all day, drivability was fine. What to do?
1. Just keep driving it?
2. Does changing fluid fix this problem?
3. Rebuild the trans, because this was just the first notice.
4. Sell it quick no light and drives fine.?
View 6 Replies
My 1999 Passat 1.8T (AEB engine) with 120,000 miles has run very well lately.............except for a recent problem. I drove 150 miles on southern California freeways, parked the car for an hour, then started it again. There was a distinct miss and the check engine light began flashing. I turned it off, let it sit for a couple hours, then plugged in a code reader. There were two codes, both the same - P-0302, "Cylinder #2 misfire". I pulled the cover off the engine, wiggled the wiring to the #2 coil, cleared the codes and started it up. There was no miss, maybe there was a little corrosion on the electrical connection?? I know there was a recall on the coils, but my car was too old to participate in the recall. Which it is - bad connection, bad coil, or something else? Or a way to diagnose it further?
View 2 Replies
Wifes car began to idle very rough and check engine light began to blink and beep, I took it to the mechanic today and he informed me that my control module was no good and it was a $400 dollar piece. I said go ahead get it done, cuz she needs the car and i couldn't afford to not have it done immediately. Question I have is does this small-ass piece really go for that much on average and what control module is it?
View 4 Replies
I have a little more detail on when the truck starts and does not . I have gone out the past two days and put the key in the ignition and turn it to the on position and all the lights come on except Service Engine Soon light and truck will not start. I bought a ceramic electric heater and placed it on the floor directing the heat under the dash. after ten to fifteen minutes I go out and put the key in the ignition turn the key to the on position and the service engine soon light is on and the truck starts right up. I let it warm up for about a half hour and then shut it off. I then try to start it right back up and the service engine soon light comes on momentarily then goes off and the truck does not start?
View 5 Replies
My 01 f150 keeps blowing a fuse. It makes the O.D. light flash, only have 2nd gear, motor runs real bad. I forget how many codes it had but it was a bunch. It doesn't blow the fuse rite away. Sometimes its days between sometimes its hours. Where to start looking for the short?
View 8 Replies
Need to identify this part? I believe this part is causing my check engine light to continually come on, due to worn out connectors (I.e. Vacuum leak)!
View 8 Replies
I have a 1997 ford f 150 with a 4.2 ltr v6 the check engine light came on so i took it to autozone and had the code pulled. They told me that the o2 sensor bank2 sensor 1 which is before the converter had a slow response so i checked the wiring and bought the o2 sensor. They told me bank 2 is the passenger side but well i changed the1st sensor on the passenger side and reset the code and drove the truck about 130 miles . and the light came back on. After reading a few posts. I think they told me wrong is the drivers side bank 2 or is the passenger side bank 2 ...
View 14 Replies
My 2001 F-150 4.6L was hesitating around 1500 RPM and the check engine light was on, dealer said the oxygen sensors needed to be cleaned. Had the work done and the problem still exists, the check engine light intermittently came on. I tried 89 octane fuel and the check engine light is off and the engine runs smoothly. I'm just a weekend mechanic and can do mostly basic stuff but the only time I've come across something like this is when I accidentally put 87 octane in my bike.
View 4 Replies
99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 Replies
I bought my 2003 F-150 XL (4.2L V6, 2WD, had 165k miles when purchased, 170k now, battery is a Napa brand manufactured in April 2012) in June 2012. A few weeks after I got it, I started having some weird issues. The check engine light came on and I went and had the codes read at Advance Auto. They were P0171 and P0174, lean bank one and lean bank two. The vacuum leak causing these codes isn't the issue I'm dealing with, it is the electrical problem.
The truck will occasionally flash every light on the dash (service engine soon, low fuel, oil, coolant temperature, seat belt, door ajar, and a couple others if I remember correctly) when I turn the key to power on the electronics. The first time I turn the key all the way to crank the truck up, it cranks fine, starts up, and dies within 3-4 seconds. The second time, it does the same thing. Third time, it just cranks and cranks, but will not start. After cranking and not starting a few times, the truck basically just clicks because the battery is run down.
This problem has happened randomly since June. It might be six weeks, one week, or only a few days between occurrences. The last two times it did it, I took the battery out of the truck, put it on a 6 amp charger overnight (about 8 hours), put it back in the truck, and it still wouldn't start, lights still flashing, etc. I gave it about 2-3 hours and both times the truck would start strongly and without incident, and the service engine soon light was off.
It rained here a LOT this summer, so I figured it might have something to do with driving through standing water at various speeds. The problem seems loosely associated with rainy weather (it rained last Saturday and I had to drive approximately 10-12 miles in it), but now it has started something new.
Yesterday afternoon, I tried to start the truck and it did the above described problem. I took the battery off and put it on a 10 amp charger for about six hours yesterday and left it disconnected overnight. Reconnected it this morning, gave it a couple of hours, still nothing. I remembered one time a while back that hitting the odometer reset button made the dash lights stop flashing. I held down the reset button and everything stayed lit up, but stopped flashing. Turned the key with the reset button held down and the truck started right up, but the dash kept flashing.
Turned it off, tried starting it without holding down the odometer reset, would crank, but not start. Tried starting it while holding down the odometer reset again, started right up. When I turned it off and tried it a third time, it just cranked for about six seconds before I gave up. This time, the oil, coolant temperature, battery, and service engine soon lights stayed lit (not flashing, they were solid) and the truck refused to start anymore.
Before it did the odometer reset BS I thought maybe I could figure it out because while it was a ghost of a problem that randomly came and went, it was always the same issue. Now I'm COMPLETELY lost.
View 4 Replies
I got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
Ive got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
2010 GTI 6 speed. Bought used in Jan '11 w/ `6k miles on it
The past few mornings, from a cold start, my car has been running weird. There has been sort of a grinding noise when the rev's get above maybe 3k rpm and the Check Engine will flash, but then turn off once I shift and the revs are back down. The problem seems to go away once the engine is warm, and it seems to be worse the colder it is outside. It seems to have started last week after I hit a really bad pothole (the kind that makes you shed a tear for your poor car).
What the problem might be? I'm planning to take it to the dealer later this week (the problem seems to go away when the car is warm).
View 11 Replies
I have a problem nobody can figure out. My check engine light is on. Took it to Advance to have it scanned; came backwith Code 1226, Brake warning light ground short ( not concerned that at this time); Code P1285, cylinder head over temperature; and P1299, engine overheating (this repeated 4 times).
Now for the symptoms: Truck start and runs good, except with engine light on, runs about 4 miles, then the temperature gauge goes all way up, oil light come on (But oil pressure gauge is OK), Have loss power, and heater has no heat. I shut key off, restart, runs perfect, gauges OK, heater OK.
View 5 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
