Ford F-150 - 1997-2003 :: 1999 - Stuck In Second Gear - Shaking / Misfiring And Stall Out
May 8, 2017
I have a 99 f150 with 171xxx miles and the other day it suck in second gear and start shaking and misfiring and would stall out. I took the truck and got the codes read and it threw codes for the tcc solenoid and shift solenoid. I put both in the transmission and it kepy doing the same thing. I check fuse 24 under the hood and it was blown, I replaced it and everything worked fine for a day then it blew the fuse 2 more times and i cant figure out why it is blowing that fuse. I cant find any shorts maybe pcm??
View 5 Replies
Advertisement
I have a 99 F150 4x4 with the 4.6 Motor approx 150000miles. Transmission went out so I decided to try and replace it...
New/rebuilt tranny went in with no problem but something is not right. It will drive but seems like it is stuck in high gear and bogs the motor down. It is giving me error codes P1747, P0750, P0755, P0743, P0102. All the wiring harness is in good shape with no burns or other noticeable problems. Somehow the transmission isn't reading right?
When I bought this rebuilt transmission I was told it was set up for 2wd but he would convert it for 4wd. The only difference i noticed with the new tranny is the shaft coming out of the tranny, where the safety neutral switch is, has a diamond shape instead of the oval shape that connects the shifter cable. No big deal i think, just had to buy a new link for the shifter cable with the diamond.
Also on the passenger side of the tranny there is a nine pin plug. My wire harness from the truck has one pin hole that is opposite of the tranny. Not sure why. Do I need a new harness or wrong tranny?
View 1 Replies
I have a 98 F250LD, its a Lariat, so everything electric/auto. Shift on the Fly 4x4, 5.4, 188K, Factory rear air suspension. Typical Minnesota rust. Anyway, I just noticed in the last 75 miles or so, a drive-line vibration. There is nothing until 39 MPH. Then from 39-41 MPH there is a decent vibration. Stops until 50, then from 50 MPH up it is a steady vibration. I have already changed the u-joints in the rear shaft. I have pulled/wiggled on everything else I can think of with no luck of finding of anything loose.
One thing I did notice, is that the front axle is locked in all the time. How long it has been like this: years for all I know... I can flip the switch from 2wd to 4H and 4L. It all seems to work fine, I hear clicking, the 4x4 engages, the proper lights come on/off. The front axle will pull when supposed to. The transfer case seems to be working fine, but the front axle won't disengage. I am hoping this can be fixed cheaply/easily (DIYer), and also hoping this explains my low fuel mileage.
Front axle? Where to look or what to try and fix for the vibration?
View 2 Replies
I have a 2001 ford f150 4x4 xlt and it seems to be shaking violently in first gear when I try to release the clutch slowly. The person i bought it from said he had a new clutch put in this year So i don't think its the clutch. What could be the cause of it before I take it in to be checked.
View 2 Replies
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
View 7 Replies
I have just put in another transmission and the truck will not shift out of first gear, it will go in reverse and first and reverse. The guy who had it before me had the same problem when he put in a transmission with only about 40-60,000 miles he assumed it was a bad transmission. And that's how I ended up with the truck. We have so far installed yet another transmission and it is doing the same not shifting out of first that it did for him. There is no cel or blinking overdrive lights, checked fluid levels, checked selinoids, gonna purchase a used computer for diagnostics, I am stumped with limited knowledge. The dealership said the transmission should be the e40d I'm reading it should have the 4r100 is that correct? The truck is the 5.4L v8 with 74,000 original miles. Truck sounds amazing. I really want to fix it.
View 2 Replies
I have a '99 F150 w/ the 5.4 and 4R70W, with 226K miles. I am experiencing what I believe is a TC shudder after the tranny shifts into OD between approximately 40-50mph. This sounds like a pretty common problem with this particular tranny, but some of what I've read describes the shudder as feeling akin to driving over rumblestrips, but what I'm experiencing is a very sharp, bucking. Is this how the TC shudder feels, or am I actually dealing with a misfire. Btw, I did completely change the tranny fluid with Mercon V, and added a friction modifier, but no change. I also read that the TC unlocks when the brake lights come on, so I tried lightly hitting the brakes when the bucking was occuring, but it continued.
View 14 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 1 Replies
Ford F150 1999 5.4 XLT... I've had this truck since may 2013 from the 2nd owner who only drove it
occasionally to make sure it ran. For the last 5 weeks there have been two occasions where my service engine light appeared...once on 12/28/15 and again today. Both read cylinder 4 misfire. Upon searching this piece which I'm assuming is the boot that covers or houses the spark plug is very unsecure and causes a shaking feeling as I accelerate or idle. Being so far back I can't reach it with extensions on a ratchet and barely fit my hand back there. Having to consider taking it into a shop for further analysis and repair but I'm trying to save as much money as possible as I am in between jobs since mid January. I have a picture attached...
View 4 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
I have an 1999 f150 4.2l only 82,000 original miles.i have had truck since new .i just replaced the spark plugs for the first time.i used autolite plat. I also changed fuel filter the truck started to run like crap now shaking and sorta like missing.i pulled the plugs again rechecked the gp reinstalled them installed new wires still runs like crap.went out bought new motorcraft plat. plugs gapped at .054 still runs like crap..so i checked the gap on original plus that have been i the truck since new the gap on them are .074-.075. should i try and gapp the new ones to this the truck ran like a dream with the original plugs at this gap????
View 14 Replies
I have a 1999 F250 4-wheel drive with a 6-speed tranny. The tranny is several old but has only around 100k on a rebuild. Three times recently it has stuck in 6th gear (overdrive) and I had to get really rough with the stick to get to come out. Afterwards the stick felt "thick" for a while and eventually everything seems to go back to normal. Not for sure but it may have started after pulling a heavy load, around 16k, which is not unusual for the truck. Other than the times it stuck and shortly after, the tranny seems perfect.
View 5 Replies
Trucks throwing codes for cylinder 3 and 8 misfire. I pulled the plugs and both were covered in oil and cylinder 8s electrode was literally gone. so I replaced the plugs and within 5 miles it was missing again. so I replaced all plugs, all wires and coil packs. cylinder 8 plug had fouled out. Its a 4.6l 99. I have a mild exhaust leak where the manifold connects to the downpipe. but not bad enough I feel it should matter. it runs rough until about 3k rpm and then it kinda straightens out.
View 14 Replies
Need some input on miss firing on acceleration on a 2001 Ford SuperCrew F-150 Lariat, 5.4 engine. 200,290 miles.
Have replaced all spark plug boots covers (Sept 2012), number 1 plug (Sept 2012), 3 and 7 plugs replaced, 3 and 7 has heli-coil kits (2011) installed for blown out plugs. New in-take manifold (2010). New gas line filter, air and oil filters (Oct 2012) and oil changes every 3000 to 3500 miles. Have poured 12 oz. fuel injector cleaner in gas take two times with 6 to 7 gallons of fuel in gas tank (last 2 weeks).
Have No check engine light on for service engine but have had an diagnostic scanner analyzer plugged into driver side, in cab outlet, 4 different times to see if I have a bad coil on plug or other problems. No codes show up indicating any problems. The engine idles nicely when at stop lights but does have a slight intermittent miss at times when warmed up and stopped at lights. Engine misses when warmed up on acceleration (when it is under a load and on acceleration).
Had a mechanic tell me he could plug an analyzer into engine but couldn't guarantee he would find anything wrong. This sounded like a little snow in July to me and the mechanic didn't sound optimistic.
View 3 Replies
I have a 1999 f150 with a 4.6L 2wd 278k miles. I got this truck from my cousin about a year ago and it ran ok but not much power. It sat a few months and I tried to start it and nothing. I replaced the fuel filter and pump and battery. It starts but runs very rough. I then replaces both coil packs, plugs and wires. It idles rough but seems to run fine in park besides some popping and shuttering when I give it gas until the rpms are up around 3k, it smooths out.
I put it in gear and it completely looses power and barely wants to move. Only code that showed was the egr, I removed and cleaned and no change besides no codes at all now. it still will barely move. I have looked for any vacc lines that might have came off but do not see any out of place. the heater core has been bypassed and exhaust has leaks from someone welding on new exhaust and not being able to weld good. Also it smells like it is running rich.
View 3 Replies
I have a 97 F150 with a 4.2. It has started to surge or stall out when I slow down sometimes. It doesn't do this all the time. I replaced the fuel filter about 2 mths ago and replaced the fuel pressure regulator then also. Would the tps have anything to do with it? I haven't had a scan done yet. Thought I would try here first because at one time someone has removed the two cats and the check engine is on all the time.
View 4 Replies
Been awhile since I've been on here...guess that's a good thing! Current problem...about a week ago my car stalled after starting it. I had been running errands all day so the engine was warm. Started fine, and then slowly died. My husband replaced the IAC valve. (My truck had this same problem 3 1/2 years ago...it was the IAC).
After replacing this time, it seemed to be fine. However today, again after running errands, the engine stalled slowly after I had started the engine. It seemed like it was trying to stay running, but then just slowly died. I tried starting again and it stayed running, so I was able to get home. It seemed to run fine while driving home. Also, no engine light has come on. Wondering what could be causing this. Don't want to get stranded somewhere.
View 7 Replies
97 F150 4x4 XLT 5.4L... I had two cylinders misfiring, removed COP, injectors and plugs. Reinstalled all parts and reconnected all sensors. Now I am not getting fuel to the injectors. Double checked for disconnected wires and hoses, checked all fuses and relays, also the inertia switch. Fuel pump does not hum when key turned on. Tried hitting bottom of gas tank. My question is, before I pull the tank again, is there something under the hood I may be missing. It does get quite crowded at the rear of the motor.
View 6 Replies
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
View 14 Replies
I have a 1997 f150 lariat 4.6, at some point i started losing power, so of course I had my friend come by and check all the mechanics under neath the hood and besides needing caps and rotors all seemed well under there, so twice I've put it on a computer and it needs and o2 sensor, I've already checked my Cadillac coverter , and dropped and replaced my gas tank twice, I ended up having to replace a shock, it does run better when i put heat through it for a short time.
I've been checking my antifreeze and I am not losing none, I also did regular maintenance to it to figuring it was a fowled plug but still no good , so whats next ? coils ? I didn't replace my plug wires but I checked them all and they looked to be in good condition and I have a transmission filter kit to change that out I don't believe its been done ever ..
View 5 Replies
I have a '99 f150 singlecab xl sport 4.2 2wd 5spd with 139,xxx miles on her. Shes's a good truck, but second gear is shot, I can only get into it by double clutching, and that only sometimes works. I have a couple questions, the first one being what do yall think the problem is. To me and my friends it seems like the syncro mesh. Second, if it is something major, is it even worth saving the truck? I know she isn't worth a ton but I hate to go through the hassle of selling and buying a car.
View 1 Replies
