Have a 2001 F150 FX4x4 and since the weather changed and started having days below 40 the truck has started running rough for about the first 15-20 miles. When you first start it starts like normal for first 3-5 min and then it starts loping real bad like it has a cam in it!
View 5 RepliesI have a 1999 Ford F-150 XLT, with the 5.4 and a 4spd auto. 172,XXX miles on the clock and i have owned it starting on April of 2014.
Tonight driving home from work, it took some time on the highway (4 miles) to shift into top gear. When you lift off the gas pedal after reaching the speed limit, normally the truck will shift from 3rd to 4th no problem. When I let off the pedal, there was no gear change.
It took sometime for it to shift up. When downshifting on the exit ramp, there was nothing abnormal. Where I live it is 19 Degrees Fahrenheit and this is the beginning of the cold snap that will last well into mid-January of next year.
So I recently acquired a 2002 F-150 4x4 super crew with the 5.4 V-8. It idles rough (surging from 400 - 700 rpm) when cold, and sometimes dies, but more often then not it stays running. It runs and drives fine when the accelerator is pressed and when going down the road. When it gets up to operating temperature, and has been there for a while, it seems to idle fine 95% of the time. The codes I have are P0136 (bad circuit to O2 sensor), P1151 (HO2S detects lean mixture or something like that), and the infamous P0171 and P0174, which is lean exhaust/mixture on both banks. Now I have read extensively on the internet about these symptoms and have done the following:
Sprayed every vacuum hose with carb cleaner, and even around the intake manifold and injectors.
Considered the IAC (its new, the guy I bought it from replaced it a couple months ago) Torque app for android phone says vacuum is good. Cleaned the MAF and air temp. sensor with electrical cleaner Checked all of the vacuum hoses on the engine by pulling them off
Put grease around the fitting where the PVC valve attaches to the valve cover. Seemed to make it idle a lot better after messing with it, but I don't know if it was a result of the engine being fully warmed up, or my messing with the PVC.
What to try next? I'm close to just dissecting the top part of this engine and seeing what the intake manifold gasket looks like..or could it really be an 02 sensor?
Sunday my truck began to sputter at idol while at a light and continued when parked. My first assumption was another coil pack has gone out. Went to autoparts store to get a new one and run the codes to tell me which cylinder it was. Code P0357 came up referring to cylinder G which seemed odd to me as it usually gives me a number rather than a letter. Bought the coil pack and went home to swap it out. Replaced the coil and with no change in the idol I googled the code. I have now replaced the coil, inspected the plug and wires around the plug and now I am at a loss of what to do next.
There is only a rough idol, no hesitation when driving or accelerating. Along with that, I've notice that if I'm going between 30-50 and take my foot off the gas it doesn't slow down, it's as though the cruise control is on... After a few miles on the highway and come to a stop, the RPMs are around 1k for about 30 seconds then drops to almost stall before catching itself and begins to sputter.
2000 Sierra 1500, 5.3L engine. When he starts it in the cold (below 40 degrees) at first hits 1000rpm, then immediately drops to 400-500rpm. The idle is rough and wants to die if he tries to drive it. However after 10-15 minutes and the eng warms up, its fine no problems at all. There is no codes, so the scanner we had didn't tell us anything. He had cleaned the TB and intake system with cleaner, no dice. He also disconnected the IAC while it was idling rough, that didn't change the way it ran at all. We would like to toubleshoot it more before we start throwing parts at it.
View 1 RepliesMy idle seems to always be somewhat rough whenever I put the heat on in cold weather. While in drive I'll come to a red light, heat will be on and I'll stop. The. my idle will bounce down then back up. I shut heat off to test and it only does it while heats on.
View 5 Replies2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
I have a 2001 Ford Escape, and since the colder weather set in it is tacking below 1 and 'jumping' when idle. When accelerating and/or once the heat gauge has reach midway, the car is fine. I added a bottle of gas additive to the tank 3 weeks back, but the problem persists. The engine light is on but no code is registering.
View 2 RepliesA problem with having a 12 volt battery maintainer hooked up to your truck when not being used for a few weeks? In this cold weather the new battery keeps drawing down while not in use and is slow to turn over after 1 1/2 weeks or so? I think the maintainers charge at about 1.5 amps. I wonder if that can keep up with all the parasitic draws: PCM, radio presets & clock, remote door lock system, and factory security system and keep the battery topped off as well?
Also, is there any problem with putting a charge on a battery when the cables are still hooked up to the trucks electrical system with either a maintainer or a full size charger, Example: screwing up the PCM?
I have a 2001 Toyota Sienna xle that started running rough when the weather turned cold. When started, the car idles very high and will not shift properly until it was been running for around 5 minutes. After that it will run well for about 10-15 minutes and then begin to run rough or poorly. The problem is very noticeable at low speeds and when stopped. It never actually kills, but it feels like it is going to. At high speeds it is less noticeable but occasionally you will feel it jerk or chug like the transmission is slipping or a belt or something.
I took it to a mechanic who checked the codes and found that the ignition coils were supposedly bad. I say supposedly because they replace three of the ignition coils and the problem still persists. I then took it back to the mechanic who then told me it was the oxygen sensor. The o2 sensor was replaced and the problem is still there with no noticeable improvement. I again to it back to the mechanic who tells me that they scratching their heads.
I have done some looking around on the internet and have found some discussions that seem to have some promising leeds and actually last weeks car talk show had a caller who described a similar problem. The guys told him it could be a oxygen sensor but they thought a better possibility would be EGR valve or a vacuum leak. Not sure if this sienna has an EGR, but I plan to suggest looking into it to the mechanic. Also, I found some discussions talking about the idle control valve and the engine control module.
Does the 2002 7.3 have an automatic high idle in cold weather?When you start it after it runs for a few moments it goes into high idle until you hit the accelerator. I had a 96 powerstroke before this one,it didn't do this. Just wondering?
View 4 Replies2001 F150! It does this weird little surge, burping and farting away...but only in ambient heat. The engine never gets hot, it never over heats. What have we done? A full tuneup with new plugs and boots, oil change, new air filter, gas filter. It did it again...took it back in and had the fuel pressure checked, fuel injectors are fine...it can't be the fuel pump, it runs great unless it is hot weather. It has twice blown the P0171 system lean bank 1 code and has gone away after the tuneup and again after the new o2 sensor. It runs great, except in hot weather, starts surging and losing power...
View 9 RepliesI just acquired a 2003 with 5.4 L. Did all new plugs and coils, cleaned MAF sensor, changed air filter, oil, transfluid and filter (obviously not related).
Upon start up and idle the truck has is rough, enough that it will vibrate the whole truck SLIGHTLY. Once in gear and warm, it smooths out and is fine. Unit the next stop and start.
I got a 97 f150 4.2l from my neighbor. he takes good care of his vehicles. he sold it to me cuz it started to idle very rough like a misfire. it is hard to start when cold spits sputters and pops. once started idles like it wants to stall, then will idle normally then back to rough. back and forth like that. runs like a champ when going down the road . check engine light was on took it to auto store they checked codes . said bad o2 sensors so i changed them. still same issue. neighbor changed coil packs checked spark plugs and wire. every thing fires good. i changed iac. still didn't fix problem. could this be a bad egr valve or sensor? if so how can i diagnose this? he also thought was a clogged cat and bored it out. tight budget can't afford to take it to a mechanic. Was told spray carb cleaner spray around engine to check for leaks that did nothing at all...
View 14 RepliesI bought this truck used and when it's in drive the engine idles rough and seems about to stall when the ac is on at a stop sign or red light.. I've tried it w/o the ac on and it seems a little better but not as smooth. Idle in park is fine.
When I should start looking? Spark-plugs? spark plugs wires, disturber cap, fuel filter etc...
When it's cold outside my car will start up, but not stay running. The only way I can get it to stay running is to keep my food on the gas for up to five minutes. Once the vehicle is warmed up, it stays running. If I start it every hour or so, it will run fine. It's just when it's been sitting out in around zero degree weather overnight for example.
View 4 Replies2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
I have a 2000 F-150 5.4 L. I was driving from home and seconds after the engine went into a rough idle that wouldn't let me accelerate. I scanned it and gave me multiple transmission trouble codes, about 15. I checked the wiring, the transmission fluid and it all looked good. So, what could be the problem?
View 3 RepliesBought the truck knowing it needed a little work because it sounded like a diesel when running. So I had the timing chain, tensioners, water pump, etc. replaced and that fixed that problem. Then, a couple days later, a spark plug blew out of the engine. So, I go to do a full tune-up to find out that 3 of the 8 cylinders already had heli-coils in them.
I pulled those three and bored out and re-tapped the cylinders using the Cal-Van inserts. This has worked beautifully so far. I also replaced all of the other plugs as well with double platinum plugs. I also replaced all COPs. This got the truck running again and it drives great. No loss of power whatsoever. It just runs like a dog at idle. As soon as I give it throttle it smooths out completely.
It seems like the problem gets worse as the engine starts to get up to normal operating temp. Basically, if I am idling, in gear or in park, the truck shakes pretty bad. It kind of feels like it's starved for fuel or barely missing. I do not have any codes though and if it is a miss, it is completely gone under throttle.
Other things I have replaced within the past couple of weeks:
EGR
EGR vacuum solenoid
DPFE
Both PCV elbows
PCV valve
Air filter
Harmonic balancer
Other things I have done:
Cleaned IAC
Cleaned throttle body butterfly (including EGR ports)
Checked TPS voltage
I'm sure there are other things that I am forgetting.
The idle seems low to me but I'm not sure what is considered standard for the 5.4l. Mine idles around 600 in park once engine is warm and the needle doesn't move despite the roughness felt. Just going by the tach, you would think that the idle was smooth as silk.
Truck info:
2000 Ford F-150 XLT
5.4L V8 2V
150k miles
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
I bought a 99 f150 lariat 4x4 with the 5.4 from a guy who said that it needed an oil pump. He said it lost pressure coming into work, he turned it off and coasted in. I towed it home and replaced the battery and bought a new oil pressure sending unit just to be sure it wasn't that.
Those things are so hard to get to. Finally I got an oxygen sensor tool on it and it was only hand tight. Rather than take it off I just tightened it up and started the truck. The dash guage read normal but the truck was idling so badly. Steady at about 1000 rpm and tooth rattling. 1500 with the foot on the pedal it evens out but still rough. Not sure if this was a good idea but I took it around the block. No power under 2500 rpm. Barely moving even. Just felt like there was no throttle response at all and again very rough.
Got it home and parked it. Now I'm wondering what to do to fix the Idle and power problem. Where to start would be great. And input on the oil pressure sending unit too. I suppose I'll have to get under there and replace it at some point anyways.