Ford F-150 (2004-2008) :: 2006 - Vibration In The Steering
Nov 20, 2012
I have an 06 4x4 lariat 4dr. 5.4L.... bought it used about 6 months ago with 107 K on it, and put a few thousand miles on it. haven't really had any problems with it, but I have noticed that when I break about 45 mph, my steering wheel gets shaky, I've tried reading on some forums but haven't really found anything very useful, and I alot of the information is on the '04 models. And honestly I"m just not really sure what to make of it all, and I don't wanna start replacing random stuff just taking a guess. I live in south texas at the moment and the air here it's salty, so I'm hoping that something just corroded and is warn...My guess is a front bearing.
View 8 Replies
Advertisement
I have a 04 stx f-150 4x4, had the front springs changed, shocks and struts! now when I am driving at either 43mph or 53 mph, I get vibration in steering wheel.....
View 6 Replies
It feels like I am having a front bearing issue, when turning the steering wheel to the right I feel a slight vibration in the steering, need to know which one is going out,??? I have already replaced the passenger side twice It just seems to not tighten completely as I can still move the tire slightly while up on a jack...
View 12 Replies
My truck had a slight vibration at idle today and what i noticed the most was i was looking at the top of the motor and i noticed that the fluid in the power steering reservoir was shaking back and forth like i was shaking the container. Is this from the vibration or is the power steering system vibrating. I have had this truck for two weeks and it has 135k on it. It is the 5.4 motor...
View 1 Replies
Today I caught a deal on a 06 F-150 with the 5.4l. I noticed a slight vibration that comes and goes at highway speed (65-75), when I got home I jacked the front end up and checked everything out. The right front CV axle is still engaged with the tire when it is out of 4 wheel drive, I can engage the 4wd and everything locks in and works as it should. My understanding is that the axle should spin free and independent of the wheels when in 2wd? How would I go about troubleshooting this?
View 4 Replies
So I have a 2006 f150 a wile back the steering started going stiff when I would come off the highway. so after some forum searching, I decided to buy a new steering shaft to repace the universals that see up. then the pump started squealing when we turned befor I could install the new shaft. so I replaced the pump and didn't put the new steering shaft in yet. now when I rev the motor past 2000 RPM the pump wines like when you turn the weeks to far to one side on an old truck and it is still stiff when I come off the highway. Could this be the rack
View 14 Replies
I have an 2006 Super Cab that has 72,000 miles on it. Stock everything except for Magnaflow exhaust and Hankook Dyna Pro tires. Last month I noticed some weird "hang" ups with the steering when turning and it just seemed to be a bump or something while turning. I was gone on vacation last week and started the truck after a week of sitting and the steering acted like it was binding or hesitating. It almost felt like a tire was down, got out and check pressures, everything was good (high if anything and got it to the right pressures).
After driving it got no better potentially worse. I start a turn and it is fine but at a certain degree it starts to bind and seems like the power steering is not there. It does not return to normal position easily either. I have checked the fluid and it is fine, the belt is normal (and original) with no tears, or rips in it. Not sure where to start, but have a couple thoughts of power steering pump going or front end has issues? Best description of the problem is that it is a binding feel and happens both left or right turns. Have to force it like the power steering is out.
View 7 Replies
I've got an '06 F150 and the steering isn't right with it. It has had a heavy feel and is almost like the power assist is only working half as good as it should. It's been like this for a couple months. I 've had all four ball joints and the steering rack replaced in the last month. It had the heavy steering feel before and after everything was replaced. It also doesn't recover itself on sharp turns, I have to turn the wheel back as I complete the turn. Could it be the power steering pump? I thought it was a mechanical device and it either worked or it didn't, maybe they get weak?
View 14 Replies
I purchased a 2006 Lariat crew cab 4x4 back in early feb... since then, I've been on the Interstates a little more than usual ( traveling back home.. dad had a surgery 3 hours away) . . . anyway, the truck gets kinda loose feeling when coming onto bridges and off of them, almost like the back end is swaying and the tires are leaving the ground in the front.. my steering wheel gets loose for a split sec. When I bought the truck I wrote this off as bad tires.. it had some over inflated BFG stock looking tires and where too small.
now, I have new wheels and new tires one size up on the tire. While the ride is great off any bumps.. the second I hit a bump it gets squirmy... I had a guy look at the shocks, he said the seemed ok.. could it be possible to have the wrong shocks on ?
My 2004 crew 4x4 did not do this.. so I know its not a characteristic of the truck. Tired of feeling like I am driving on ice... which is how I lost my 04. My first guess was the Shocks... I bought a level kit for my 04 and never got to put it on... so, it may work out to replace them while I am at it.
View 12 Replies
Replaced the Intermediate Steering Shaft at 114,000 miles. Symptoms felt like power steering going out but no pump noise or low fluid. Steering became hard to turn and it sometimes felt like a tie rod was letting go.
Temporary resolution was to spray the two steering shaft joints with penetrating oil (PB Blaster). That freed them up pretty well. Then I ordered Dorman part 425361 (425-361) from Rock Auto. Simple enough job. Lots of good vids on YouTube.
I don't recommend spraying the steering shaft joints as preventative maintenance. Penetrating oil will get into the needle bearings and break down the bearing grease. That will cause the joints to fail over time.
Two side benefits, the truck steering is much smoother and small road bumps and potholes are much less noticeable. Feels like it was when new.
View 3 Replies
I have been having this problem with Gf's car for a few months it is a 06 3.0 escape with 141K on the clock the car seems to run ok except at red lights and when in drive it seems to idle like its just about 100 rpms low when I give it a little gas just a touch it smoothes out. if I put it in neutral the car smooth's out but in drive when you come to a stop light or stop sign you can feel the rough or low idle in the steering wheel. She is nagging me and it has been very cold here in Pa and I'm trying to wrap my head around if it is a cold thing or just a coincidence. I'm fairly good at wrenching and I just need some things to look for as when you start the car up cold it idles fast like 12 to 1300 rpms and then drops to about 900 and in drive it seems like maybe it's about 600 to 700 rpms. but where to start to look Is it a sensor, vacuum leak ?
View 6 Replies
I recently had new rims and winter tires installed on my 2007 Hyundai Sonata 4Cyl from Walmart. When I left I noticed I had a vibration in the steering wheel at around 50-70 km/h so I took it back the next day and got them rebalanced. After the rebalancing I asked the tech. if it was off and he did say they were just a little bit off.
I took it out for a drive and the vibration is gone from 50-70km/h, now it is vibrating from 70-120km/h. I was about to take it back for another balancing, but as I was driving home today and had the car on cruise control and cruising at about 110-120km/h I noticed the vibration would go away sometimes to virtually nothing, then come back with very noticeable vibration.
So now I am beginning to think it has nothing to do with the balancing of the wheels but maybe something in my suspension. I am getting some clunking sounds when I hit bumps and you can feel it through the drivers floor, pedals and steering wheel. I had friends tell me that it may be a tie rod end or strut mounts.
View 3 Replies
I have a 2008 Pontiac G6 GT. I loved my card until I had to replace the rotors and changed to an all-weather tire. Now, I can feel a vibration in the steering column; a vibration in the seat and floor; there is a noise in the front of the engine when I am going over bumpy or icy roads; and the car pulls to the left when I have been stopped at a light or an intersection. Oh - When re-starting on a slightly icy or gravel-y road, I also get a sound that sounds like gears grinding -- not like the traction control is kicking in.Frustratingly enough -- the car can go from feeling like it is driving "tight" -- like the power steering is out -- to driving "loose" like the steering wheel is ready to fall off the car and vibrates like it never has before. No one notices the vibration but me (which is frustrating because I have driven my car over 30,000 miles, and what seems "normal" to others, is not "normal" to me).
View 13 Replies
I recently had u joints and left front wheel hub assembly replaced at a local mechanic. Ever since I have a vibration between 40-45 and 52-62, the vibration can be felt in the steering wheel, the seat and the floor. The mechanic claims I need a new driveshaft as some of the counter weights were starting to rust. I indexed and removed the drive shaft and had it rebalanced at a local machine shop. This did not solve the vibration problem. There is also a transmission leak starting from the extension housing. How I can start to trouble shoot the problem. 04 F150..
View 2 Replies
Recently got in to a 2008 F150 STX.
I started noticing a vibration in the truck when reaching 55-60mph. Anything under that is a smooth ride but like clockwork, once I reach around 55, a vibration I feel in the cabin kicks in.
I just took it to a Ford service dealer around my way and they inspected everything about the tires, including alignment and all was good. That was my first guess and what I heard is most common with this issue.
What would be the next possible culprit? A belt maybe? Kinda lost on where to move forward without spending all kinds of dough on testing.
View 10 Replies
I have had a 2004 Extended Cab F150 5.4L for a few months now. It just started vibrating at speeds between 15 and 30mph on accelerating or deceleration. Doesn't matter if I'm turning or going straight, just those speeds. It's fine otherwise. I put it in gear and held the brake down and brought the rpms up to 3000 to see if it would shake with a load, thinking a possible misfire, but nothing abnormal.
It's an automatic transmission. I started off in 1 and 2 and it seems to lack power until it shifts to 3rd gear - which is about 30mph. It also seems to lack power in reverse ... no slipping, but seems to have to give a lot of gas in order to go over the slightest incline backing up.
View 1 Replies
I have a 2007 ford f150 supercrew. I have a vibration in the front end at around 55mph. Doesn't vibrate at lower speeds or when you get above 60 mph. I have replaced the struts and just put new Michelin tires on it. Wheel bearings feel fine and front end bushings, tie rods and control arms look fine to me. It feels like the vibration is coming from the left side. I read somewhere that a possible cause is an upper control arm.
View 5 Replies
I have a 2006 Camry with a steering vibration at 60-65 miles per hour. I have looked at all of the Threads for similar problems but everyone is guessing at the cause....stating "Check the alignment, check tire pressures, check the wheel balance, check the wheel bearings."
I have checked all of these things to the best of my ability and there does not seem to be a problem there. I bought new tires and had the front end aligned. Vibration still there. Had tires balanced 3 different times. VIBRATION STILL THERE. Removed wheels and inspected all suspension parts. No obvious problem seen. Switched tires front to back then left to right then front to back again. VIBRATION STILL THERE.
Forgot to mention that the right front is wearing on the inside but the alignment checks out. I had the alignment re-checked at the tire dealer and then checked it myself later in the month using toe plates that we have in the shop for our SCCA ITB Club Racer. Is there a Recall that I am not aware of ?????
View 2 Replies
I have a 2006 Camry 4 cylinder that I turned the rotors on all four wheels and replaced all the brake pads on all four wheels with ceramic pads. I did this a year or two ago.
Now this doesn't happen every time you brake but sometimes you will get a vibration in the steering wheel when braking.
When I had the rotors turned at O'Reillys they said they were too thin. So I had them bring out a new one and that one was too thin as well according to whatever specs they were using. So they turned my old ones.
And the car doesn't pull to either side when braking. There are not grooves in the rotors and it doesn't make any screeching when braking. I did notice that there is a ridge on the edge of the rotor when you run your finger across it from the inside to the outside of the rim of it. My guess the rotors are warped.
And if the rotors need to be replaced is this rotor better than the stock ones and thicker? [URL] ....
View 7 Replies
I'm having an issue with my 2005 f150 xlt. Its been happening for almost near a month and still cant locate the issue .
It has a vibration at 75km throughout the whole truck. Ive tried multiple things done to it by a mechanic, such as having the tires balanced and the ujoints replaced. The problem still persisted and after attempting to test out to see if press/releasing the parking break (my mechani suggested trying that out), my driveshaft fell off.
Apparently the center bearing snapped and cant simply be replaced on the 05's. So i had to get a new driveshaft installed (used, both the 3 mechanics I've gone to say its in good condition).
Even after replacing the driveshaft the issue persists - however it seems a bit softer than it was (I am guessing the old driveshaft was worn from the vibration causing it to be worse). After that I took it to another shop to see if they could locate the issue. They did a driveline inspection and engine inspection too see if a misfire could be the cause.
Again, nothing was found. The only thing they were able to find was that the issue only happens under load and slightly occurs at 40 and 100km as well (although alot softer then the one at 75) and they say they cant find anything physically and it was a mystery to them.
View 2 Replies
I purchased a used 2008 F150 with 62,000 miles. The truck is in excellent condition and is a crew cab with the short bed and the 4.6 v8 engine. I changed the 17 inch wheels to a set of Ford 18 inch wheels with Goodyear tires that came off another 2008 F150( XLT model). The tires had less than 15,000 miles on them. Since that time I have replaced 3 of the 4 tires because I could not get the tires to balance out properly. I have had all the tires and wheels balanced with the road pressure balance and the front and rear end have both been aligned.
I cannot get the RIGHT REAR of the truck to keep from bouncing and hopping at almost any speed. It changes from day to day a little bit but while slowing down I get the hop vibration( when I apply my brakes) and while at speed ( mostly 45-55) and above 65 I can constantly feel the truck vibrating. It is apparent it is the right rear. I took it back to the dealership where I bought it used , they could not find any issue. At some time, the rear cover to the rear end has been taken off but I cannot find any information through normal channels as to why.
I was by the shop that balanced the tires it is a Goodyear problem. All I know is that I cannot enjoy my ride due to this very apparent hop/bounce from the rear end. The alignment shop said they could not do anything more to make it better. Is there a FIX to this? Is it a problem with this model truck? The truck has 69,000 miles on it now.
View 3 Replies
