I have an 86 F150 that is idling rough. It used to cut out on me until I replaced the fuel pressure regulator. I have read in other posts that the problem for my rough idle could be leaking injectors. When I replaced the regulator I found a bad injector. My question is that if I check my fuel pressure, with the new regulator, would the only way I would lose pressure be that my injectors are leaking?
View 5 RepliesI've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 RepliesI have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 RepliesWhat to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.
My engine is running rich, flooding? My truck is a 1986 F-150 302 EFI. The engine idles rough, black smoke and soot comes out the exhaust pipes, and black soot on spark plugs. Symptoms seem to disappear if I throttle the engine and hold it, but as soon as I release the throttle the symptoms reappear and in most case causes the engine to die. These symptoms have just started a week ago. What the problem is.
Fuel injectors are cleaned and rebuilt. New plugs and wires. All new fuel pumps and filters. New air filters. New fuel pressure regulator. New dual function reservoir. New 3-piece timing set. New O2 sensor. New EGR Valve and sensor. New idle air control valve. New distributor, cap, and rotor. New ignition coil. New high volume oil pump. New alternator. New pcv valve. New knock sensor and air charge temp. sensor.
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
I have an 87 f150 inline 6 efi. The truck will not rev over 2000 rpm even when idling. It has a new fuel filter. What this could be?
View 2 Replies1987 f150 302 4spd 4x4. When I bought the truck 4 years and 12K miles ago the orig owner had just installed a new front pump (in tank) and new switch thing on the frame rail. He said shortly after that the rear pump stopped working so he just ran off of the front tank. That's what I've been doing also except as of the last few months it has started to leak from the rear tank (I don't ever put gas in it and was empty when I bought it) and dies periodically from time to time? Where the leak could be coming from. I do suspect the dying has to do with the leak though.
View 3 RepliesI have a f53 motorhome and 4 out of the 8 injectors pulse. The front 2 and the back 2 don't pulse. The middle 2 on both sides work perfect. Why would they not pulse and only give out positive on the two wires to the injector on the one that don't work. The ones that work they pulse.
View 8 RepliesI have a 1988 f-250 with a 460 motor. I have fuel and I have fire. And the truck starts with I prime it. I tried looking for the crank sensor but can't find it. I looked behind the balancer and I didn't feel any wires or anything. I checked on the sides of the motor nothing. It has a new coil pack and ignition mod. Fuel pump and starter. What else can it be?
View 4 RepliesAfter changing a head gasket, I went to fire up and noticed three injectors are leaking where they meet the fuel rail. They weren't leaking before tearing everything apart and nothing was done to the rail other than moving it. From what I've searched, it sounds like O-rings. 2002 2.0 Jetta.
View 3 RepliesI have a 1986 27ft Class C RV on a E350 chassis, 460 ci with about 140,000 miles on it. I inherited it when my Dad passed. I live in the southwest and I am have trouble with it, it seems to be a fuel supply problem, I think?
It runs fine on level ground, but we tried to go to the white mountains this weekend and could not do it. On an incline the engine would start to starve for power. At times we could only drive at 25 mph! It kind of seemed like it was running out of gas, if I tried to give it more throttle it would just die or fall on its face, if I let off the pedal and gave it gas again, it would run for a bit and then do the same again. We were lucky to get it back home. I replaced the electric fuel pump (on the side of the road) during the trip, but that made no difference.
The engine ran cool the whole time! it has only one 40 gallon tank. I can find any other fuel pump on it. but don't understand all the lines going to and from the gas tank either?
I noticed there are these silver metal tubes that feed off the exhaust manifold up to a cylinder looking thing on both sides of the block. One of the tubes is broken from the ex manifold and the manifold is plugged. Not sure how this got damaged or what this parts function is but was wondering if this could be a problem ..
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
Looking for the wiring diagrams for 86 ranger fuel system. I replaced the fuel pump relay after testing and finding that it was bad, still not getting fuel. I want to test any fusible links or anything else that could have gone wrong before I throw another part at it.
View 1 RepliesMy vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 Repliescant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 RepliesWhy the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 Repliesfor the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies1994 150 300 6. parked truck after lunch finished work and it wont start no fuel comes out of the valve. Can't get the pump to work even when jumping the 6 pin. heard the relay click still nothing. Checked the inertia switch it wasn't popped. Took the pump out jumped it straight from the battery pump works . I know there has to be something i am missing...
View 7 Replies