Ford Fuel System :: Running Rough - Skipping / Surging And Die
Feb 3, 2016
I built the 400 in my 79 a couple years ago and it runs very well...until yesterday. I'm about 80 miles into this tank, and on my way home from work, I thought I felt a vibration (not in the steering wheel, but in the front oc the truck). Then the engine became evident it was running rough and was skipping and surging. I stopped.
It idled pretty rough, then died. Fired right back up, ran rough, and died. Sometimes it would idle smooth for several seconds (20-30) then start surging and skipping and die. I could hold a little throttle and it would run about the same, except some backfiring in the exhaust (more like a big hiccup).
The carb is a 670 Street Avenger with nothing really done to it. The bores are really black (not sooty, more damp or so). I have always used the air filter, so that's odd. I took the carb off and removed the bowls. Nothing inside has a dirty or clogged appearance at all. Not sure if I should completely rebuild it.
View 6 Replies
Advertisement
I just completed a successful second spark plug change, using Motorcraft SP515 plugs just like last time. After reconnecting battery and starting engine, it ran poorly throughout a short road test. Felt like it was skipping. Checked under the hood and found that the #2 fuel injector was disconnected, so I reconnected the injector.
I took another short road trip and it still ran poorly as if skipping. So, this time I disconnected the battery for several minutes while removing the #2 plug thinking I may possibly have fouled the plug by the injector not being connected. I also checked all of the other injector and coil connections. Reconnected battery and took another short trip. It still runs poorly. No codes yet.
View 14 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 Replies
Our 2007 Avalon with 65xxx miles on it was skipping and running rough this morning. Running a scan with my VAG-COM gave me these codes.
Mode 07: Pending emission related fault codes Address 7E8: 2 Faults Found: P0305 - Cylinder 5: Misfire Detected P0355 - Ignition Control Circuit for Cylinder 5: Malfunction
Would you say it is time to replace the Coil for this cylinder, or should I do more troubleshooting first?
From what I've read on this forum, it appears cylinders 1, 3 & 5 are at the rear of the engine and are a PITA to change. Is there a good write-up or video on how to change these at the rear of the engine?
View 2 Replies
I have a 99 f-250 with about 250k miles. Truck is completely stock. It recently has developed a problem where when I start it in the mornings it surges at idle, 200 rpm or so. Sometimes it tries to die and did once but started back up. When driving it continues to rev itself up and is jerky. It runs rough and sounds like it could be missing on a cylinder. At other times it runs fine just like normal. Yesterday morning it started with these symptoms so I put in a new ford CPS. It ran great for about 100 miles that afternoon. This morning it started back with the same symptoms. The SES light stayed on longer than normal when I started it, but it went off. I don't have a scanner.
I thought it might be water in the fuel because this started the day after I filled it from my transfer tank. But the water in fuel light has never came on. I put a new fuel filter on it but it made no difference. Have pulled filter three times looking for water but never found a drop. Also pulled several buckets from the bottom of my transfer tank but found no water there either. Where to look next?
View 5 Replies
I have a 1994 gmc sierra 4x4 5.7 with a rebuilt engine 2 yrs ago and it has started having a rough idle(surging/dies) I have replaced fuel pump, fuel filter, maf sensor, iac sensor, tps sensor, top half of the tb and injectors, distributor, ignition module, plugs and plug wires and still no change. Yesterday I cleaned the iac and seemed to straighten up a little but then got in it to go to work today and it was back to running rough again and seemed worse. I am at a loss.
View 4 Replies
Had the oil changed yesterday and changed the air filter myself. Car is now running rough, surging, when in drive and stopped. Runs cleanly when moving and surge is significantly less in park and neutral.
View 3 Replies
I have a 99 f250 that seems like it has a bad coil, under a load it starts surging or bumping ( like it has in the past and I found a bad coil), I went through and unplugged each coil one by one while idling, couldn't find a bad one, so I bought a new coil and went through and rotated the coils, nothing worked, no check engine lights on.
View 9 Replies
I have a 2000 hyundai accent and when i fill with fuel it surges like its running out of fuel and stalls when fuel is gets low it runs fine.
View 2 Replies
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
View 2 Replies
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 Replies
The pumps at times will function what appears to be normal. At other times the pumps will not stop running and it is at those times when the engine does not like to run.
I do not know if the engine will not run due to too much pressure or not enough fuel pressure. The problem is with both tanks and pumps so I do not believe the problem is inside either of the tanks.
One problem is that I just got the truck and the prior owner had at times done a little work and you know how that can be a problem. He could have done some damage to some hoses or who knows what. He had replaced the radiator and the left side exhaust manifold recently, though at different times. He thinks the problem started around the time he did the radiator. I know it doesn't make sense but things can get bumped or damaged.
What would the problem be that it could come and go? I drove it for a few miles and I thought that maybe the problem had gone away after I replaced what appeared to be a short vacuum line by the throttle body. But the problem still comes and goes. Now the truck is stuck till I figure the problem out.
View 2 Replies
My mechanic tells me I need the intake manifold gasket replaced (check engine light on, engine surging, running very rough). How much damage can I do to the car by doing this repair myself and screwing it up? I've done lots of repairs on my car before -- brake pads, rotors, replace oil pan. I also have a copy of the manufacturer's shop manual.
View 2 Replies
The carb on my 460 in my truck is acting funny. It almost sounds like a dragster It Idles really rough. I tried setting the Idle mixture screws on the side of the metering block. I bottomed them out and them turned them out 1 1/4 turns. I started turning them in till I got the highest reading on my vacuum gauge, about 13 hg. The screws are only about 1/4 turn from being bottomed out. It was running smoother, then it stalled when I restarted it, it started running really rough again.
The exhaust smells of gas. I turned the screws all the way in just to see what would happen, I thought it should stall but it didn't. I had my timing light hooked up and checked it now and then during all of this and it didn't change at all. The screws had almost no resistance to turning, shouldn't they have some resistance?
View 6 Replies
Have a 1977 ford f150 with 351m with a motorcraft 2150. Had ( who I believe was a reliable source ) rebuild carburetor for me and after putting back on I can only keep engine running with foot on pedal. I turn idle mixture screws all way in and then proceeded to back out equally. This does not appear to be doing anything. I did turn the choke 2 notches to lean and was able to get it to idle but it wasloping so bad i shut it down and put the choke back to the middle setting.
View 13 Replies
What to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.
View 2 Replies
I have a 1994 f 150 5.8l 4x4 with 215000. Cold starting is fine runs well. After running it will not start after shut down. Wait till motor cools back down will start up and run fine ....
View 2 Replies
How many O2 sensors does a 2.3 fi 4 cyl. have. I think just one on the manifold, but I'm not completely sure. Engine is running very rough and seems to miss at low RPMs, has no power and drinks gas like crazy!!! Emissions light is on on the dash. I'm thinking O2 sensor......tried replacing, but couldn't get enough torque on the sensor socket wrench to loosen, may be rusted.
View 6 Replies
My engine is running rich, flooding? My truck is a 1986 F-150 302 EFI. The engine idles rough, black smoke and soot comes out the exhaust pipes, and black soot on spark plugs. Symptoms seem to disappear if I throttle the engine and hold it, but as soon as I release the throttle the symptoms reappear and in most case causes the engine to die. These symptoms have just started a week ago. What the problem is.
Fuel injectors are cleaned and rebuilt. New plugs and wires. All new fuel pumps and filters. New air filters. New fuel pressure regulator. New dual function reservoir. New 3-piece timing set. New O2 sensor. New EGR Valve and sensor. New idle air control valve. New distributor, cap, and rotor. New ignition coil. New high volume oil pump. New alternator. New pcv valve. New knock sensor and air charge temp. sensor.
View 14 Replies
I just had a former Ford tech rebuild my motorcraft 2150 2v on my '77 F250. I took it home, put it back on the truck and it ran kind of rough. I then went ahead and screwed both idle mix screws in untill seated, then back out two turns. The truck ran great, turned off truck then when it the house for dinner. Half an hour later I come back out...truck will not start, just sits and cranks. Finally got it started and it ran good, but crapped out after it warmed up. I have made sure there were no vac leaks when truck was running the first time. Did I adjust the mixture right?
The truck is a '77 F250 400/C6
View 2 Replies
