Ford Ranger / B-Series :: 1992 - Truck Stopped Running While Driving / Started Again Then Died
Apr 19, 2012
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 Replies
Advertisement
I have a 2003 Ex 6.0 psd, 155k miles, and was on my way to work to a site 40 miles from nowhere. I was about 10 miles from my destination cruising around 65 when the Ex started losing power. I would say within a couple of miles power was gone and i had no choice but to pull over. I popped the hood, got out had a look around and saw no leaks or anything out of the ordinary. Let it sit for a few minutes and tried to restart it to no avail. There was no check eng light or any signs something was wrong.
I just so happened to have my OBD scanner with me and plugged it in and read for any extra codes. Three popped up on the screen: P0232, P0263, and P0278.
P0232 Fuel Pump Secondary (Feedback) Circuit High Voltage,
P0263 is described as a cylinder number 1 contribution/balance. In essence, this code is stating that the number one cylinder in the firing order is experiencing a fuel-related problem.
P0278 same as above for cyl 6.
Right away i thought the fuel/lift pump took a dump on me and was causing the fuel issues in the two cylinders.
View 12 Replies
So a couple days ago I started my truck and it fired up like normal, but then sputtered out and died after a few seconds. I tried starting it up again and it did the same thing. I tried once more and it started up fine and I drove away.
It sounds like my truck is running out of breath or something and just sputtering out. Runs fine once it turns over though. My issue is that it is happening almost every time I start it now. I have to turn it a couple times before it catches. What this might be?
View 11 Replies
My Dad has a 1992 Toyota Pick-up with a 22RE engine it is a 2 wheel drive automatic. The truck stopped running while idling, he did code tests on it and they came up clear. He can get it to run on propane but not on gas. He did change all the spark plugs, distributor cap and rotor, and spark plug wires.
View 13 Replies
I have a 1992 Ranger with 2.3L that suddenly lost power on freeway and stopped and couldn't restart. Towed it to Seattle, WA and need Ford Ranger 2.3L engine mechanic to double check the timing since new belt installed to make sure it was done right before cover and rest of engine reinstalled.
View 5 Replies
My truck will fire while the starter is engaged ,but stalls when the key is in the run position. This is my plow truck and I don't want to go through the winter without it.
View 14 Replies
Truck quit running yesterday suddenly and unexpectedly. It sputtered briefly and the motor total quit running. I pulled over and tried to start and it briefly fired but then totally quit. Got towed home. And now testing to see what all to repair..Thinking fuel.
I don't get any codes from the tester with KOEO..just the good to go etc..no codes or the good to go 111..etc. Guess this problem can't be identified without motor running.
My wiring diagram doesn't give me all for my Calif car..I don't see where the relay is but my fuses are all good, and I'm getting voltage when I crank the motor at that inside firewall switch on both its wires(incoming/outgoing)..forget what its called..Inertia Switch?..that will shut off fuel pump during accident or impact etc. And I've read that this switch is upstream of the relay(if I read that post correctly) so guessing it's the pump itself that is bad.
Does that sound right? Should I go ahead and pull the fuel tank etc and replace the pump? Or is there more testing I should do? When I turn the ignition key on..the pump makes zero sound. That's not the way it normally operates. Usually with the key on the fuel pump comes on momentarily and I can hear it. Forget how to drain the fuel tank etc..I don't see a drain plug? I did it once many years ago..but forget how?
View 7 Replies
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
View 14 Replies
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
View 8 Replies
I have a '96 Ranger XLT. Just recently the dome light stays on while the truck is running. I have checked both doors and door frames. For the life of me I do not see a switch. The light does go off eventually after the truck is shut off (without killing the battery). What or where is the switch for this light..
View 14 Replies
So I turned off my truck the other day, got out, and it started again on its own. Confused, I looked in my hand to see my key. I got back in, and tapped the brake thinking the command start had engaged, even though I did not have the remote with me. It continued to run. So I put the key back in the ignition, turned it to ON and back OFF. It still ran. I had to run inside for a half a minute so I left it running.
Came back and drove away with no issues. When I stopped again about 2 minutes later and shifted to PARK, the starter engaged making it's terrible 'hey stupid, I'm already running' sound. I tried shutting it OFF quickly but it still ran and made it's skinning crawling noise. So I quickly shifted back to DRIVE. All the gears worked fine but PARK and NEUTRAL had the starter engaging. I also could not shut the truck off from DRIVE as the key would not turn.
I drove over to a local garage and called them from the truck as I was effectively trapped in the truck with my foot on the brake, unable to shift to PARK or turn it OFF. No supporting staff. So I drove back to work where I had a co-worker remove the battery cable at which point I was able to shift to PARK and turn OFF the truck. I let it sit like that for about 10 minutes and haven't had a problem since.
What happened?? And for the record I can put gas in the tank and changed my own oil, but that is the extent of my vehicle knowledge.
View 14 Replies
I have noticed that my temperature gauge is indicating that usually my truck is running very cool. It seems that it is also somewhat erratic. At times it indicates what I would expect a reading in the middle of the gauge. Other times after running a while it will drop to the lower end (cool) of the gauge and stay there.
I am guessing that the thermostat is sticking open. Is there a way to test the sensors to see if they maybe bad? I have a 99 ranger with a 4cyl. It looks like I have two sensors. If one is bad, how can I determine which it is?
View 14 Replies
I was driving along as happy as could be, and suddenly lost power. 2000-2001 Ranger, 5 speed. After I got it home, I plugged in a charger, tried jumping it and all. I was getting a few turnovers, now I only get a click. Wipers, Lights and fans all work so there is some power at least.
I finally found my Ohm Multimeter and checked the current from battery to power box.
battery + to - 12.96
battery - to power - 0.00
battery - to power + 12.96
battery + to power - 0.00
battery + to power + 0.00
Now that just seems insanely odd to me.
View 1 Replies
I have a 99 ford ranger xlt 4.0 ohv basically it sputters so bad while driving it sounds like a dump truck but it all started when I changed my o2 sensors but in doing so I broke my heater control valve and when I was going down the road it started sputtering well it started sputtering so I checked the o2 sensors there good and I changed the heater control valve. But nothing so I changed my coil pack spark plugs and wires but still nothing. But on my reader it says cylinders 2,3, and 4 are misfiring and bank 1 and 2 are running lean plus it has a bad aroma of gas in the engine compartment but when it idles its somewhat smooth but when I'm driving it its horrible the sputtering is so bad it takes awhile to get up to speed plus I'm only getting 100 miles to a whole tank that's like 8 or 9 mpg I need to fix this soon. This is my only transportation...
View 11 Replies
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 Replies
2002 Ford Ranger edge 3.0 flex ... Truck was running fine and giving me no issues. I woke for work the other day and went to get coffee and truck wouldnt start. I could hear fuel pump running and knew it wasnt that, it was acting flooded. So today I pulled fuse from fuel pump relay, and got it to start. Put the fuse back in and ran to gas station. On the way to the gas station it started running really rough, very low and rough idle, trying to stall out. I noticed it had black smoke coming from exhaust. I got it home, and got it to start barely, and it has the same very low and rough idle, but my oil gauge was going crazy, flickering back and forth all crazy, and the idol is terribly rough and eventually stalls out. Earlier today I did put new spark plugs in it, but not sure that has anything to do with the issue. I also hooked it up to a computer and it isnt throwing any codes.
View 13 Replies
The problem : I bought a 2004 Ranger truck and after two days it started to hiccup, or stall or die while driving, then because the truck is manual, just start up and keep running. It was the strangest thing.
I gave it to a shop, and after checking the electrical, the ignition, the fuel system, the drive train, and ten hours of troubleshooting, they came up without an answer. So they gave me the truck back.
Answer, a few days after taking it back:
I had told the shop that it had been sitting for 6 months, May till January, but when I told a mechanic friend a bit later, he still suggested 2 bottles of gas line antifreeze in the tank, before the next tank fill. I did that, and there was some improvement.
Next, When I replaced the balding tires with new Nokian Winter tires, the tire shop, (Kal Tire), told me that the air cleaner was incredibly dirty, and asked me if I would like them to replace it. I said yes, thinking that it might just do the trick, as no one in the forums I read, had mentioned it.
Success! No hiccup or stalling and it has not died since.
View 6 Replies
I was driving up a hill an it started to loose power. i got up to the top of the highway an stopped an it just shut down. got towed home i thought it could of been the alternator but dose not seem to be. took the belt off to spin the motor an its not spinning. drained the oil an there is no metal in it to see if the motor was done. i try to start it an it just dose a click click an that's it. Is the motor done or is it a transmission problem?
View 3 Replies
My 2000 ranger, 5 speed, won't start. I was driving, and all of a sudden, the engine just stopped.
Electrical works, engine turns over once or thrice, but it never actually turns on. Wires and belts all appear fine.
View 8 Replies
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 Replies
On my '91 last week I was driving on the highway about 60-65 when all of a sudden the speedo dial started climbing to 70-75-80-85 and past. The odometer seems to be working ok? Still when I drive it still operates in the same manner. It never bounces around or falls back. The needle is sort of stable such if I maintain a speed the speedo will maintain even though it's incorrect. There is a slight wavering of the needle meaning it's not as stable as it use to be. With the odometer working I was wondering and don't know. Does the cable drive the needle or is it electrically controlled? I'm thinking of grabbing another instrument cluster it that is the problem, I'd like to know more about it and understand how it works so I don't just throw parts at it until it's fixed.
View 1 Replies
