Ford Ranger / B-Series :: 1993 - Cruise Will Not Disengage With Brake Pedal
Sep 24, 2013
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
View 6 Replies
Advertisement
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 Replies
I have a 93 Ranger xlt and after checking wheel cylinders and calipers first I have found a leak that is coming from the brake line or maybe the RABS module. The leak is up along the inside of the frame and I can't get in there because of the gas tank. Has to change line or RABS in that area and am I correct in thinking the gas tank has to come out to do anything in there.
Also, in the manual it says to plug the line as soon as you remove it(at wheel cylinders etc) so the fluid does not leak out of the RABS because it can't be bled without an expensive piece of equipment. I am pretty sure it probably emptied due to the leak location.
View 3 Replies
I have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 Replies
I have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Replies
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies
So, a few day i bought an 84 Ranger and even since have not been able to figure out what the hell is wrong with the brakes. I know it's not the brake booster for starters. Because, i went to Auto Zone and picked up a new one and when i took the old one off (before i had put the new one on as well) i tried to see if the brake pedal would now move freely and it won't. It is still very stiff and squeaks when you push it down. i then to get it to return have to pull it up with my foot... What it might be? the WD-40 failed here as well.
View 3 Replies
What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 Replies
I have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
View 14 Replies
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 Replies
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 Replies
I recently acquired a 1989 Ford Ranger midsize pickup with an electronic shift button/console between the visors. I put it in 4WD and the manual does not indicate the procedure to take it out of 4WD. What is the procedure?
View 3 Replies
Its and 03 ranger with a 4.0 auto and it grinds after starting and it doesn't always start smoothly, like it hops around till it finally starts, kind of like the starter wont disengage. Do I start with a new starter or is more than likely a flexplate issue? I hope its just a starter.
YouTube video : 2012-02-16_15-35-45_211 - YouTube
2nd problem is it hesitates a second or so before it goes into gear and clicks in hard, kind of like when you are low on oil, but its not low on oil. It also shifts hard. When I got it the column bolts were loose so the shifter was floppy, I am wondering is someone tried to fix it the wrong way. Also now its pretty stiff to move the shifter selector.
Also what tranny is in it, it may be some sort of heavy duty unit, it was an x electrical municipality vehicle, it appears to have an 8.8 and heavy duty rear springs. Door tag reads axle rd, tr D, and spr 2c...
View 9 Replies
I recently bought a 2006 Ranger with supposedly 110000 miles... I don't think I made a good deal... because I found the stabilizer end link in terrible shape which seems suspicious for this mileage in my personal opinion!? But this isn't the reason I am posting today... I have a serious breaking issue and I couldn't find explanation yet.
My ABS Light is on. When I slowly brake at low speed and when the brake is almost completely depressed... I hear a low humming sound, and the brake pedal seems to momentarily drop back just slightly. This also happens when I'm going down hill and breaking. For the most part, the car breaks, and it's only every 8th or 10th time braking that I experience this issue.
My guess is this is linked to the ABS... but I can't afford expensive service and need to resolve this on my own.
View 2 Replies
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
View 3 Replies
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
View 1 Replies
My clutch went out on my 98 Dodge Ram 2500 4WD the other day. I limped it home shifting like a big truck timing the shifts w/out the clutch. I replaced the slave cylinder w/ an aftermarket that had a bleeder. Bled it and got the pedal back up and it still wouldn't disengage the clutch. I replaced the master cylinder and started getting pedal back until I let the reservoir get too low and now after plenty of tries, I can't get any pressure built. I get a stream of fluid, but no air. Bench bleed the master and start over? I'm at a loss.
View 5 Replies
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 Replies
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 Replies
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Replies
