Ford Ranger / B-Series :: 1996 - Ignition Coil B Went Bad?
Apr 24, 2012
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 Replies
Apr 24, 2012
Advertisement
Ford Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
Ford Ranger / B-Series :: 1996 B2300 - Ignition Stuck In On Position
Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.
It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.
Ford Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Ford Ranger / B-Series :: 1988 - Power Loss Like Coil Getting Bad
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
Ford Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
Ford Ranger / B-Series :: 2000 - Running Rough And Code For Misfire On Cylinder 3 / 2nd Coil Pack
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesFord Ranger / B-Series :: 1985 - Truck Simply Quit / No Spark At The Coil / Cranks Just Fine
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
Ford Ranger / B-Series :: 1996 XLT - ABS Not Communicating
My 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
Ford Ranger / B-Series :: 1996 - Won't Start And Crank Even?
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
Ford Ranger / B-Series :: 1996 - Putting SB In Place Of The V6?
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesFord Ranger / B-Series :: 1996 - No Heater Control
I seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesFord Ranger / B-Series :: 1994 - No Spark At Ignition Module
I have a 94 ranger with the 2.3l engine there is no spark at the ignition module (the front one both on the drivers side) that controls the plugs on the drivers side of the engine. I swapped with the module for the exhaust side but the problem stays at the same two plus and doesn't move with the module .. What can be the source of this problem? ECU?
View 6 RepliesFord Ranger / B-Series :: 1997 XLT 3.0 - Pre-Ignition Spark Knock
I recently replaced the plugs & wires on my '97 3.0L XLT automatic, and now I'm hearing some pre-ignition (spark knock). Only happens under light load, as in climbing a slight grade on the highway. No CEL, no codes on my code reader. Was not happening before I did the work.
The plugs & wires I removed were the factory originals (AWSF32P & PG, 3 of each), truck only has ~85,000KM (~50,000 Miles) on it. Well maintained, & only used occasionally. The only mod from stock are the wheels & tires, I'm running 215/70 R15 instead of the stock 225/70 R14, the difference in the tire circumference is minimal.
The gap on the old plugs was just over .050", no evidence of any fouling or other problems. The new plugs are Autolite XP104 Iridium, which is what the Autolite catalog calls for. Plug gap was checked & set to .044", midway in the range called for by Ford (.042-.046).
I realize that the narrower gap on the new plugs will cause a slight advance in timing, and I have done a computer reset/relearn as per Paw Paw's instructions. I'm stumped.
Ford Ranger / B-Series :: 1996 - Power Steering Replacement
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesFord Ranger / B-Series :: 1996 - Squeaky Rear Wheels
I am working on a 96 ranger 2wd the front brakes were shot or nearly so,about 1/8 in left and cracked. Changed them this morning at 5am because that is the cool of the day (104 today) everything up front works fine but the howling and nails across the chalk board from the back was still there. Took it to my freindly les schwab and they told me it needed axle seals on one side and the noise is from the gear lube on the shoes. they wanted 800 bucks to fix everything, went and bought new shoes,new seals,gear oil,and gasket for rear end cover it is an easy half hour job. As I was driving home tonight from the parts store the noise stopped so now i am worried either it was a rock stuck between the drum and backing plate or something broke. everything sounds and works fine....
View 2 RepliesFord Ranger / B-Series :: 1996 - Oil Leak Coming Out Above And Behind The Filter
I have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 RepliesFord Ranger / B-Series :: 1996 - Codes P1131 And P0401
Originally started with a p0302 code, and it cleared. CEL came back on with codes p1131 and P0401. First time with an 8 plug 4 cylinder. Truck has 263000 miles, and still original (metal) DPFE sensor. 1996 ranger 2.3L.....
View 1 RepliesFord Ranger / B-Series :: 1996 XLT - Radio Controls Don't Light Up
My 1996 Ranger Supercab XLT has the stock radio with 6-cd changer. The unit works fine but only the frequency/clock display lights up. I'm not sure where to start to fix it.
When a problem first occurred, the frequency/clock display flickered/dimmed randomly (and I think the other lights were fine). It was in the shop a few times for a fuel pump problem (the after market pump was actually not compatible and it took a bit to figure that out), and at some point after I got it back I noticed the display was fine but the remainder of lights didn't work.
I don't know if the shop did something or the failure behavior changed. What to look at? I can open the radio and fix that if needed (or replace it).
Ford Ranger / B-Series :: 1996 - Growling Noise From Differential?
I have been hauling a lot of garbage with my 96 ranger this last week. The differential has been making a little more than usual noise like growling, but it has always been smooth, now all of a sudden it shakes like a tire out of balance up to about 55 then it is like a switch is thrown and everything quiets down and the shaking goes away, until i get around 55. I haven't climbed under the truck yet just checked the tires and grabbed the drive line they are all ok,i don't see any leaks so it is a head scratcher. Hopefully it will be something easy, but it hardly ever is.
View 7 RepliesFord Ranger / B-Series :: 1996 - Transmission Slipping When Cold
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 Replies