Ford Ranger / B-Series :: 1996 Truck Idles From 500 RPM And Randomly Jumps Up To 2 - 3000 RPM Then Back Down
Sep 7, 2015
I have a 96 ranger with the l4. Right before I bought my newish truck last December, it's started miss firing and running really bad. I replaced the spark plug wires, most of the spark plugs, and both coil packs. Didn't work at all. Then I bought my new truck and parked. Fast forward to now. Fired it up, ran REALLY bad. We changed the wiring order from the 96 order to the 99 order.
But the truck idles from 500rpm (barely running) and randomly jumps up to 2-3000rpm and then back down. Driving it has NO power, rev it and it stays at 2-3000 for quite awhile. Sometimes it randomly dies. REALLY need to get it running quick and cheap. Getting ready to sell my daily driver to find something else and I need something to drive while I hunt for another truck.
View 1 Replies
Advertisement
My truck jumps or runs roughly... I don't know how to describe it. It's like if someone dumped the clutch. It's a manual, it does it through all gears, so I don't think it's the transmission. I was thinking it might be the fuel pump, but I don't know how to diagnose it. I've got an 83 with the cologne v6. I think it's just got the engine driven fuel pump, no electric, but I'm not sure. Either way, I think it could either be the fuel pump or maybe a vacuum leak.
View 2 Replies
I was driving around town and I kept noticing my aftermarket radio would shut down and turn back on when I put my foot to the floor, then I noticed that my voltage gauge would shoot to the H when I hit around 3000 rpm and all the dash light's and head lights get brighter but once I let off the throttle it goes right back down. I've been taking it easy lately and now around 4000 rpm it will shoot up now. But I just replaced the voltage regulator I checked the battery and cables they don't seem to be damaged and I already replaced the belt. What could cause this?
View 3 Replies
My son just purchased a 1996 Ford Ranger 2.3l 5 speed it is a nice little truck. But I have a question when you press in the clutch it acts like the choke has come on it idles way to high. When you come to a complete stop it is a few minutes before it goes back to its regular idle. Is it suppose to do that?
View 9 Replies
Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 Replies
96 Ranger x cab 4.0 ltr automatic... Starts fine, runs fine until I stop.
When I stop, the engine idles oddly - it slows and speeds back up, tachometer and the battery gauges both lower just a bit and immediately return to normal. When the headlights are on, they dim in rhythm when the gauges dip. It does not do this in park or neutral.
Sometimes it does it right away. Sometimes it doesn't do this at all. Of course it did not do this when I took it to the shop. The battery is nearly new. Cables are fine. Alternator checked out ok.
View 4 Replies
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 Replies
1999 Ranger 4.0. I have an issue with my ranger. Sometimes the truck runs awesome.While driving along the truck will miss and sputter and buck, when this happens, I almost can't maintain my speed. Sometimes when this happens if I put the truck in neutral and shut it off and restart it. The problem will temporarily go away. Occasionally it will go away on its own. When it goes away on its own it's like someone flipped a switch and all power is returned and running smooth. When the truck is at idle it depends on the mood of the truck, sometimes it's fine and other times it wants to die. I got to make this truck last awhile longer.
View 7 Replies
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 Replies
I just bought this Ranger a really bad steering issue. When at low speeds, when I go to turn the steering "jumps/kicks." Then after I straighten out at the end of the turn it jumps in the direction that the steering wheel is being turned. This goes away at higher speeds (40+mph).
I was told by the seller that it needs a new steering pump, but my mechanic said that it was operating well. He noticed that the bearings were loose on the driver side and tightened them up. The problem went away. I just finished driving it for about 20 miles and the problem is back.
What do you think? Is there a way to easily shut off the p-steering to see if that is the problem? Is this a good idea?
View 4 Replies
2002 Ranger 2.3 duratec ... My Oil Needle jumps around from center to zero. (I am aware this could be/is a dummy light style). There is a Pressure switch attached to oil filter housing, I thought this was oil pressure sender. The pressure switch I was sold is cylinder with single prong connector. Not matching the sensor on oil filter housing. What sensor is on my oil filter housing? Also where is my oil pressure sender?
View 2 Replies
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
View 14 Replies
Driving a 2008 Ranger XLT 3.0. Starts runs and drives fine, how ever it seems to have a tinny ruff idle.
What I noticed is when in park or neutral when I idle it up @ 3000 RPMs it seems like it runs on 3 cylinders and sort of cuts in and out very quickly. Is this a protection thing on the ranger.
Running on the road it kicks down and runs thru all the gears normally from idle all the way up to 5000 RPMs. Just would like to make sure this is normal.
View 2 Replies
In a matter of weeks, my truck destroyed two sets of flywheels and starters. When the ignition key engages, the engine "jumps back?. Apparently, this causes the starter and flywheel teeth to grind. My mechanic cannot determine the cause of the "jump back". He thought that it might be the timing. His examination and testing, however, proved the engine properly timed.
View 6 Replies
I recently purchased a 1996 Ford Ranger with the 4 cyl. engine. The first 10 days I owned it it ran just fine. I then took a an hour drive to another city. After the first few stops there, as the temperature outside reached about 90, It started to sputter and idle very badly. After I got rolling it would would run fine. I decided to try to make it home. It ran fine at freeway speeds of about 70 mph. I had to stop once; it stalled out and would not start again. After waiting about ten minutes I tried again. It was still running rough, but I was able to get rolling and drove the rest of the way home without any problems until I was in town and had difficulty keeping it running at idle.
The next morning it ran fine again. A local mechanic changed the fuel filter, but the problem came back as soon as the temp neared 90 degrees. A mechanic friend who witnessed the problem said that it definitely sounded like a lack of fuel and not an electrical problem. Is there a way to troubleshoot without swapping parts? If the fuel pump is failing in warm weather, how is it possible that it runs fine at 70 mph, but not at idle? Engine temp gauge looks good. I did get one code after it died the first time (lean mixture, I think he said).
View 5 Replies
Ranger often wants to idle at 2,500 to 3,000 rpm. I'm glad its got a clutch! This is a long term intermittent problem that is getting worse. I have replaced the the IAC twice. I have unplugged the IAC when the engine is in high idle and the engine idles normally. But, starting the car with the IAC unplugged makes car run rough. That makes me think the IAC is not getting the right voltage input from the pmc (eec). Mine is a 2002 with the 3.0 engine. Throttle plate seems to be closed.
What sense inputs does PMC use to determine idle air position? Also replaced TPS sometime ago but that didn't work either. Sometimes turning off the a/c will knock the idle back to normal but not always. Turning the car off completely usually resets idle. But the high idle comes right back after accelerating. Drove the car today and idle would stick and stay high when clutch pushed in coming to a light. However. as the car slowed to a stop the idle would come down when rolling 1-2 mph. ??
View 13 Replies
So that's what if feels like, in park at idle it sounds great, starts great no codes. IF you floor it it will not go over 3000 rpms in park, it feels like it has hit a rev limiter. I have 60psi fuel pressure at idle and at 3000 rpm.
When driving down the road I won't go over 55 mph and drives normal if you keep it under 3000 rpm, if you give it more gas it falls on its face?
AC is not working (clutch not engaging)I don't know if that's related or not.
We did just swap the motor the truck is a 2003 2wd drive. motor came out of an 2002 4wd. we are running the 2wd harness, computer egr delete etc.
View 6 Replies
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
View 3 Replies
96 Ranger 2.3 5 speed, 2wd. 212k on the clock.
Bought this from my BIL last week. CEL was on so I ran the codes. replaced the air filter, cleaned the MAF (with CRC MAS cleaner), replaced the EGR solenoid (physically broken). The first code showed this was throwing the code. That code (p1409) went away but p0402 showed it's head. replaced the DPFE sensor, disconnected the battery for an hour and am now code free.
Now it idles like crap, up and down with A/C on or off to nearly dying and does eventually die. Disconnected the MAS and no change. Cleaned the AIC no change, replaced the AIC with no luck. Checked for any obvious vacuum leaks around items I messed with. Found nothing. With engine running I disconnected the vacuum to the EGR valve and idle smooths out. Feel a small vacuum tug from the hose, nothing at the valve.
Haven't changed the PCV or cleaned the throttle body. Could it be the EGR valve since removing the vacuum seemed to work?
Side note, BIL's mechanic told him THREE YEARS AGO the CEL was 'probably a O2 sensor' and that is doesn't do anything and no need to fix.
Still no codes and still no power. Can't hear any vacuum leaks. Bought new plugs and wires but haven't installed them yet. EGR? TPS?
View 14 Replies
My ranger has a 3.0 v6 engine it idles high and accelerates on its own sometimes. Sometimes its more often then others. I turn my key about three times thinkin its reseting the computer and stop it and it does. But I keep hitting a dead end and don't know what to do about it.
View 10 Replies
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
View 3 Replies
