Ford Ranger / B-Series :: 2003 - Spark Knock / Idle Slightly Higher
Feb 29, 2012
03, 2.3 duratec, 163k, new timing chain, plugs (AP104), wires and intake. cleaned MAF, air filter, and ran two cans of sea foam through the intake and its still pinging. its driving me up the wall. truck runs perfect but seems to idle slightly higher and take longer to come down to idle after I got the timing chain and plugs/wires done. I've sprayed starting fluid around on top of the engine looking for vacuum leaks but found nothing. What should I try next?
View 14 Replies
Advertisement
I recently replaced the plugs & wires on my '97 3.0L XLT automatic, and now I'm hearing some pre-ignition (spark knock). Only happens under light load, as in climbing a slight grade on the highway. No CEL, no codes on my code reader. Was not happening before I did the work.
The plugs & wires I removed were the factory originals (AWSF32P & PG, 3 of each), truck only has ~85,000KM (~50,000 Miles) on it. Well maintained, & only used occasionally. The only mod from stock are the wheels & tires, I'm running 215/70 R15 instead of the stock 225/70 R14, the difference in the tire circumference is minimal.
The gap on the old plugs was just over .050", no evidence of any fouling or other problems. The new plugs are Autolite XP104 Iridium, which is what the Autolite catalog calls for. Plug gap was checked & set to .044", midway in the range called for by Ford (.042-.046).
I realize that the narrower gap on the new plugs will cause a slight advance in timing, and I have done a computer reset/relearn as per Paw Paw's instructions. I'm stumped.
View 8 Replies
So we finally found a travel trailer and picked it up yesterday. It is a 2008 Jayco 29A. Fiberglass with aluminum frame. 5345 dry weight, so shouldn't be too taxing on the Ex, but we towed it through parts of the NC mountains to get home and on steep grades it would downshift to 2nd gear and I would hear what sounded to me like pinging from the engine.
As far as I know the plugs are original, so should I just go ahead and replace them, or there also a possibility that this is just the notorious exhaust manifold leak? If all exhaust manifold bolts are still intact, is there a good test to know if it is the exhaust? No engine codes were thrown. The truck has 72k miles on it now.
View 11 Replies
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 Replies
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
View 6 Replies
I noticed a slightly higher RPM at idle (1100-1200) with outside temps in the mid 50's after a 15 mile trip. I dont recall what it usually is, it just seemed to revving higher. What would say normal RPM's are on a warm engine.
View 8 Replies
My 2003 ranger xlt 4.0 has a stalling problem. The engine light came on in aug and I had it coded at AutoZ and there was a code for the oxy sensor, changed that and didn't work so I took it back. In oct I had it coded and it said the air int temp sensor which i was informed was part of the mas airflow sensor, changed that the beginning of nov, got the computer to reset and it still didn't fix it.
Took that part back and had it coded again a few days later and several codes came up AutoZ code 1732 and the the OEM number to cross for them were: P2195 , P0300 , P0316 , P0174 , P0171 , P2197 . Reset the comp yesterday and as soon as the light came on had them code it again and it came up AutoZ code 1732 OEM # to cross P2195. I guess my next step will be to take it to the dealers to get diagnosed..
View 4 Replies
I have a 2003 Ranger edge 3.0 flex fuel 183,000 miles. I have been having a misfire problem, only at idle, always cylinder 3. Replaced the fuel filter. Just replaced fuel pump assembly. With the old pump my fuel pressure was 49psi key on engine off, and running at idle it was 59psi with a shaky needle. With the new pump, when I turn the key on it jumps to 60psi then imedietly drops to 49psi, when the pump shuts off. Running it is at 60psi with steady needle. Koeo the pressure holds good at 49psi but does slowy decrease, about 5psi in 15 minutes. What would be causing the pressure to drop to 49psi? I am checking pressure at the fuel rail. Pressure according to the haynes manual should be 60-65psi koeo and the same while running at idle.
View 14 Replies
My 2002 4.0L V6 Ranger, 4x4 overheated *slightly* this past weekend. I added some water and limped it home with a couple stops, trying not to let it get too hot. I since noticed there is oil in the coolant, so jumped to the first non mechanic's assumption the head gasket was bad. I have had (auto) tranny troubles with this truck in the past and started looking inside today and noticed some red fluid under the truck. I think the tranny fluid cools through the main radiator on this one, yes? If so, do I likely have a bad radiator, or is there another likely possibility?
The only wet areas I can find look like where the hard lines come into the right side (looking from the front) back of the rad. If we can determine that, would I need to replace the radiator, or is there any way to plug the tranny lines and run through a separate cooler? I think this also has a tranny, or oil cooler in front of the main radiator but not sure if that is correct, or what exactly that is. This is my daily driver work truck and will bring work to a stop until I can figure it out.
View 5 Replies
I have a '94 Mazda B3000 3.0L V6. The engine finally gave out at 244,000 miles. I had a used motor installed with approx. 110,000 miles on it. I now hear a knocking sound only when the engine is under load (in gear and accelerating). The knocking is not present while revving the engine while in park or neutral. The transmission was rebuilt last year about this time. I have described this problem to several respected mechanics and they don't know what it could be. What could cause this condition?
View 12 Replies
I too had this problem and tried different gas, gas additives, meticulously inspecting the cooling system to make sure overheating was impossible, found the jumper that allows me to back off timing 2 degrees, checked the computer for error codes, and cleaning the MAF sensor. Nothing really worked.
The solution is to decarbon the engine. It is all described in TSB 01-19-7, dated OCT 01. I did this and END of the problem. Pay attention to the part about not ingesting the PM-3 cleaner too fast to make sure you don't liquid lock your engine. The only important step they forgot was that you will need to replace spark plugs when you're done. You may also want to lay some newspaper under your tailpipe too, as the crud is gonna flow.
The TSB notes that the driver should have "periods of daily operation over 3500RPM to break carbon from cyl heads". They also note that you should NOT use mid-grade or super duper unleaded, as these increase the probability of carbon buildup.
This repair will cost about $30 if you do it yourself; if you can change a flat tire you can do this.
View 14 Replies
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
View 14 Replies
Had it before, code p1401. Changed out dpfe and it worked for 6 months. Now spark knock again. Now though I have no codes though. No vacuum leaks that I can find. New egr from before I had the problem. I applied vacuum to the green hose and it stumbled so the ports should be ok. Snytime I go above 3000 rpm i get the pinging. I replaced the dpfe again and no difference.
View 3 Replies
I had a friend do an alignment on my truck yesterday. Afterward, we tried to center the wheel the best we could in the shop. But when I drove it home I noticed that when going straight, the steering wheel is ever-so-slightly turned to the right. Is there and easy way to adjust this without me going back to the guys' shop and bugging him again? I know the alignment is dead nuts, but the wheel is just a tad off.
View 4 Replies
My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 Replies
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
View 1 Replies
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
View 7 Replies
I've got a '94 Ranger with the 4.0L OHV and an Automatic trans. When I start, hot or cold, it has quick lifter knock for only a fraction of a second. This same knock comes back if I hold the throttle over 3K with NO LOAD on the engine. With any load, I cannot make it knock. With no load, though, it becomes very loud, especially with more RPMs. at idle and slightly above, there is a slight tick that can only be heard with the bonnet up, and then it is only slightly noticeable. I think that this tick is unrelated, but I figured I should share that information. For oil, I run Pennzoil high mileage 10W-30, changed 3000 miles religiously. Purolator filter, PL30001. I can understand the startup knock, but I can't see why it seems to produce the same knock at high RPMs under NO load.
View 4 Replies
I have a 2010 Ford Ranger Sport. RWD with the 4.0L. Currently Sitting at 46,000 Miles.
Where I am located, it is very cold. Downwards of 5 Degrees F. I just started noticing a strange sound in my truck. When accelerating from a stop light I hear a single knock, and to my ear it sound as if it was coming from the rear. First thing I did was check the U-Joint, but there is zero play and it is very tight.
After driving quite a lot and unable to diagnose the problem, I part and got out of my truck, only to hear that same noise when I stepped out of the truck. (I am not fat 195b lol). So I sat back down and I heard it again. Did this a few times and consistently heard it. I got into the bed of my truck and started to jump around and got the same knock.
I shook the exhaust pipe to see if it was making the noise, but it wasn't, which makes sense considering while driving over bumps I could not hear anything. I am totally lost as to what this could be....I want to add that I CANNOT feel any difference driving. Feels great.
My ideas on problems are as follows;
-Spare tire
-bushing
-loose bold
-leaf spring (maybe a hanger)
-The cold creating noise like always.
View 3 Replies
Truck has no spark except when you first turn key on it sparks or right when you let off from cranking it will give one spark. You can be cranking it and nothing and when you let off it kinda acts like it wants to start for a millisecond.
View 11 Replies
1990 ranger 2.9 ... I have put about everything new on this ranger. It has no spark, ran fine til i went across a set of railroad tracks, it died 6 months ago and never started again .. Many dollars and many hrs has gone into this thing and still no spark. It will spark when you turn the key on. Crank it and 3 more sparks and thats it. Every electrical piece has been replaced. I've checked and bought relays ,fuel shut off, new distributor pickup coil, rotor, cap, wires, plugs, coil and still no start?
View 6 Replies
