Ford Ranger / B-Series :: Constant Thud Coming From Front Driver Side While Driving
Dec 29, 2012
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 Replies
Advertisement
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 Replies
I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.
I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.
1996 Ford Ranger XLT 2.3 ......
View 11 Replies
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
View 5 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
View 4 Replies
I have a 2000 Ranger 3.0 4x4 with over drive. When backing out of my driveway there was a harsh "thud" (for lack of a better word) and I lost reverse. The forward gears are still working. We pushed it out on to the road and I drove to my place of business. At that time reverse worked again. It only lasted a couple more times. Still have the forward gears. Could it be a band or clutch?
View 9 Replies
I've got an 08' Ranger FX4. Recently I had the drivers-side headlight go out. Today I replaced the light, and while I was there, I decided to check every bulb on the truck. Everything else works, but I noticed the 2 factory "foglights" will not come on. This is a fairly recent development, because I use those lights quite often.
Even thought they don't cast a huge amount of light, here in the Vancouver area, winters are dark & rainy, so I think 4 points of light as opposed to 2 points is a benefit. To activate those lights, you pull on the headlight selector switch. Do those lights have their own dedicated circuit with fuse? Or does this sound like a switch problem?
View 14 Replies
Just installed raxle on my driver side. All clicking sounds are fixed but I noticed if I take right turns sometimes you can hear a constant clunking sound coming from the driver side wheel. It doesn't happen all the time, you kinda have to turn and hit a certain angle of the steering wheel. Also, only happens when driving low, if I raise the car just a little bit its gone. Never had issues with my oem axle binding so Im not sure how exactly does the binding sound?
View 24 Replies
I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.
Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.
View 10 Replies
I have a 4 door 2005 Accent with ABS. I mainly drive in the city, and lately I noticed a squeaking noise that sounds like it's coming from the front right side (from inside the car); it is a constant noise. I pulled the brakes off both sides, the pads are fine, the rotors were a little rough (normal). Before I reinstalled everything I took some 80 grit emery cloth and roughed the pads and the rotors with it just in case there was some glazing.
The noise is still there and what concerns me more than the noise is the fact that the longer I drive the car the more gas I seem to need to apply to get the car to move.... not a huge amount but enough. Also, once I stop the car, there is a slight brake smell and the passenger side front tire area (brake) is crazy hot. Long story short; I would like to check to see if I have a stuck piston in the caliper, But I'm not 100% sure how to. Do I pull the pads off, push the piston in , watch how fast it goes in, and then compare it to the drivers' side? Or do I need to pull the caliper apart?
View 1 Replies
I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
View 9 Replies
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 Replies
1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
Changed my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 Replies
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
View 1 Replies
I have an 03 ranger and my driver side window will not roll down... My pass side rolls down just fine...when I push the down button all I get is a clicking noise out of what seems to be a little black box underneath the driver side dash and I can actually physically feel the clicking along with hearing it... When I push up on the button I get no noise or anything... this might be the motor...the regulator...or the actual switch?
View 1 Replies
I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.
Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.
View 4 Replies
New motorcraft plugs, wires, and coil packs. I'm running havoline 5w30 with a motorcraft filter now. I didn't notice the tick when I got it only a few months ago, but it could have been there and not as noisy, I'm not really sure.
I've got some parts to put on when I get time. Probably be a month or 2. I have a timing belt and tensioner, water pump, block heater, drive belt, tensioner, and idler.
It's a constant tick. Worse when cold, but still there warm. Sounds like under the valve cover. I'm not afraid to get in there and fix it, just would like to hear some opinions on what it could be for sure. I've read about the lucas and high mileage oil combo maybe reducing the noise, but if its fixable, I'd like to do it when I have it torn down for the timing belt, which is original I'm sure by looking at it. I really don't like abnormal noises from my engine compartment. Bugs the crap out of me.
View 7 Replies
I bought a 1990 ranger with only 38000 miles on it from a online auction from boing aircraft. it never left the flight line and never even had a title. I picked it up from the airport and found out that it didn't have AC like they said, I was a little ticked but that isn't the main problem. When I drive it and it gets warmed up it leaks Tranny fluid from the front of the transmission. The engine does not overheat. It is a 4 cyl AOD automatic with a real thin radiator and a transmission cooler. Without AC the truck isn't the good deal I thought I was getting, and with a bad tranny this is becoming a big OOPS. Why this is happening?
View 3 Replies
