Ford Super Duty (1999-2016) :: 2004 - RPMs Will Stop Then Pick Up And Stop - No Codes?
Jul 30, 2013
i have an 04 f250 5.4 4x4 250k miles+ ...the truck has been acting weird lately. I has 0 power...i went to pass an 18 wheeler today at about 15 mph and gave it about half throttle...well it held first gear till about 5 grand then slammed into 2nd...It just has 0 umph ... it wont even consistanly pick up speed at half throttle or over..the rpms will stop ...then pick up...then stop...it always accelerated smoothly....it is bogging really bad...it was downshifting into 3rd today on little overpass hills that it NEVER does that on...something is telling me torque converter BTW no codes and no flashing overdrive light
View 14 Replies
Advertisement
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
I have a 2005 ford f250 6.0 I was driving back home from a interview and my truck died at a stop light it would crank but no start I tried replacing the stc fitting didn't work so the I replaced the ipr still didn't work bought a new hpop still didn't work I'm lost at this point I have low pressure oil pump is working new icp, what is going on?
View 8 Replies
I have a 2004 super duty diesel 6 with electrical trouble dash lights stopped working put in new fusses where needed still no dash lights but now truck starts and runs ok but will not shut off unless I pull ignition.
View 2 Replies
2004 F350 6.0 Diesel 2WD, Question is my trailor lights running lights work fine also the electric brake, but i have no stop or right or left turn signals the truck signals are all working perfect. The truck came with factory wiring i have checked it at the plug on the bumper with meter to make sure it was not the trailor. Looked for blown fuses and cant find anything what am i missing it should have seperate fuses for trailor lights ??
View 14 Replies
I have my 2004 f250 6.8L. Recently my truck has been having issue with the oil needle. When im stopped or coming to a stop my Check Gauge light comes on and my oil needle drops all the way down. As soon i step on gas it goes right back up. What could it be?
View 7 Replies
F250 5.4L have had a new fuel pump installed and new spark plugs (one blew out). When accelerating, or at a stop i get a kinda hesitation. It did it when I first bought the truck but put correct size tires on it and it went away. What it may be? I don't have a check engine light or anything and at cruise speed no problem--it's just when a slight load is put on the engine?
View 1 Replies
My 06 f350 power stroke has a viper 2way remote starter.
When I try to start it when the truck is cold it doesn't crank long enough for it to start the truck. It will try 3 times when I hit the start button and normally won't go. It almost starts most times but stops cranking right before it starts. This is driving me nuts.
I just tried 3 times to start the truck and it in ally went on the 8th time trying to crank.
View 12 Replies
I have a 2002 F-250 7.3 Powerstroke 4x4. My truck has developed a "clunk" for lack of a better term when accelerating from a dead stop. It is not a shudder as it only happens once within a few seconds of depressing the accelerator and then goes away until the next time I stop moving.
It feels like either something in the drivetrain is not engaging right away, or something is releasing, like a stuck caliper or something. From the way it feels and what I've read so far about the TC/Trans, I'm assuming it is something worn in the drive-shaft/rear diff.
But it needs brakes badly (already have all new rotors & pads ready to install) so maybe a caliper is sticking when depressed and then popping loose under initial acceleration? I think this is unlikely but possible.
View 12 Replies
1999 f250 7.3 diesel stalls and pushes while coming to stop. So when I am stopping my truck it will try to keep accelerating then it will die. It has almost push me into a other car in front of me. I can put it in neutral to keep it from dying but it is idling just fine. When I put it back in drive it acts just fine not trying to push the truck.
View 1 Replies
I have a 2000 ford f350 7.3l with a auto transmission(4r100) and I have had problems with it . It started a while back when the transmission is cold like in the morning when I put it in drive it acts like when you don't push the cluch in on a standard when coming to a stop kind like it's bucking and this only happens when it's cold when it's nice and warmed it's fine so I changed the whole transmission and put a billet torque converter and I'm still having the same problem can it be a sensor or something electrical ?
View 7 Replies
Driving into work this morning, I came up to the first stop sign before I get on the "freeway" and noticed a weird vibration. As I slowed to stop I could have sworn it felt like the engine was being lugged, the same feeling you get in a manual when you try to come to a stop without using the clutch. I thought for sure the engine was going to die. The engine RPMs dropped to about 800-900 RPM and once I got to a complete stop the RPMs went back to normal.
It seemed to do this every time I came to a stop. Could my torque converter be locking up and not releasing as it supposed to causing the lugging sensation I'm getting? The truck accelerates fine and idles fine once stopped, but when slowing I get that weird vibration and maybe the lugging sensation is just in my imagination and has nothing to do with the engine.
I do have a vibration from a missing wheel weight, but that's usually felt at about 34-35 mph. In addition, I also have a bit of a brake vibration when slowing down quickly, such as when slowing quickly from 65 to turn off the highway onto my local road, but this is a completely different vibration.
View 14 Replies
i just bought a 99 F250 4WD with the 5.4 in it i put a brand new starter in it. When i turn the key to try to start it, it just cranks the motor once and stops. The starter isn't grinding or clicking, the motor clicks once and move the belt and pulley a little but that's it. What would cause this?
View 13 Replies
Ok I ended up buying a 2011 F250 XLT. it has the reverse aid sensors. it worked great till i washed it after plowing. what should I look for or diagnose? also mt my dash says my tires need air. I filled them and reset but it comes back.
View 7 Replies
I have a 06 f350 6.0. I'm losing hear at times. My temp gauge is right in the middle like always. As soon as I let off he throttle or come to a stop the heat turns cold and blows out cold air!
View 2 Replies
I can't afford to replace it now and want to quiet the squealing that occurs only when I turn right. A mechanic sprayed something on there about a month ago that caused the squealing to stop for about a week, but don't remember what it was. It's a 2002 S.D....
View 14 Replies
My Superduty recently started clunking when I accelerate from a dead stop. The harder I hit the gas,the harder it clunks. I unbolted the driveshaft from the rear end and the yoke slides easily. Tranny mount looks tight. Could it be the front driveshaft? Sometimes when I brake hard and the truck comes to a complete stop it will do it too.
View 14 Replies
Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 Replies
I have a 99 f350 V10 gas dually dumper. Today while driving I stopped at a stop sign. When I went to continue the transmission seemed to be in neutral, then it caught and I drove through the intersection. It 2-3 seconds later disengaged again. I pulled over. When I attempted to put it in park it grinded. (Bad enough I just turned off the key). I checked the fluid. It was close to full and red. While in park I restarted. Truck started fine. I shifted into drive and nothing. It was like it was in neutral still. I attempted to put in park again and more grinding. Also while in park it does not hold the truck from rolling. After getting towed home I checked the tranny fluid again and it was still looking ok. I drained the transfer case also. The fluid in there was near black an appeared to have a metallic look. Does this problem seem to be just my tc or tranny issues also?
View 8 Replies
I have a 2001 F250 V10. It idles around 1k and when stopped at stop lights or when put in reverse it stalls. I have replaced IAC, fuel filter, tranny filter, oil filter, plugs, coil boots, tranny fluid, oil, air filter, and PVC along with the PVC hose. I'm totally stumped. It doesn't stall if I do a rolling stop.
View 14 Replies
So, don't know if this is normal or not, but after lifting the rig, I'm experiencing a whole lot of these types of sounds from the leafs or the springs or whatever, whenever I start, stop, or turn. Is there an easy way to silence the noise? I've tried all sorts of lubricants on the leafs and springs, but I only get (at best) a week of muted noises. While it's only an inconvenience, it sure would be nice to have the rig be quiet again.
View 6 Replies
