Ford Super Duty (1999-2016) :: 2005 F250 - Cam Phaser Knock / Timing Chain Slap On Start Up And Noisy Lifter
Oct 30, 2015
I have 05 F250 SD with 150k on it. The engine has the typical cam phaser knock, timing chain slap on start up and occasionally have a noisy lifter. As long as I use fresh 20-40 oil the engine symptoms are less and the engine runs strong. The motor also doesn't leak or burn oil and the plugs were change out about 20k ago.
The truck is still good and is prefect for my needs so to me it's seems worth fixing the needed repairs. What I would like to figure out how far should I take the motor... just have the chains, guides and phasers replaced or buy a rebuilt motor and swap it? I'm thinking just doing the phases and etc would be 1/2 the cost but may not last as long as rebuilt motor. But realistically I might only put 5-7k miles are year on it anyways.
View 14 Replies
Advertisement
I have an 05 5.4 f250 that had a stuck injector. I changed plugs before I realized it was injector. After that the truck had a terrible rattling noise. I ended up changing timing tensioners and guides (guide was broken). Started it up and have the same noise, like timing chain is loose.
What I think happened is gas got into oil when injector was stuck. I had key on to pull codes. Then it lost oil pressure?
Could this cause can phases to go bad? Also can I just install lockouts or do I need to replace phasers as well?
Not sure if there's anything else I should check
View 2 Replies
Ok I bought this truck with a bad engine 5.4 3v had rod knocking. I rebuilt engine got it all back together and in truck. I did replace cam phasers and solenoids. After driving 20 mins or so it would start the phaser knock at idle in gear so I put a oil pressure gauge on it and cold had 55 psi after running 10 mins or so had 15 psi at idle then would drop to abought 9 psi. I am thinking I got bad cam bearings or something for some reason don't know why. I did it but I took oil cap off where you pour in the oil. Had to force it off it was pulling that much vaccum ones cap was off oil pressure jumped up to 25 psi. What could be causing this.
View 2 Replies
I drive a 2008 5.4L F-250. How long do the average cam phasers last. I run full synthetic at 5K intervals and run WIX filters.
View 2 Replies
Today I either broke timing chain or it fell off on the passenger side bank of my 08 F250 V10. Put a hole in valve cover. What to expect for repairs. Is this engine Zero tolerance.. unsure if I should expect bent valves or not and just how far I may have to go with this.. best way to test. I have a bore scope camera and mechanical abilities.
View 14 Replies
So, when trying to start my vehicle it doesn't even turn over. Just clicks continuously. Both of my batteries are putting out 12 Volts. I tried the old arcing my solenoid with a screw driver while key is in on position and I got a couple of turns, but it wouldn't completely turnover. My solenoid has power going to it. Checked all fuses that could coincide with this issue. Not sure where to go from here. I have an 05 Ford F-250 XLT.
View 7 Replies
I bought the wife a truck a few weeks ago and she said the heater wasn't working well and was noisy. So I hoped in it at lunch today and she was right, barely any heat output and its noisy coming from behind the passenger airbag.
View 1 Replies
My 2008 f 250 with 75k on it is making some unreal noises at 45 to 65 miles per hour. Almost sounds like someone is tapping on the top of the cab.
2008 standard cab with utility body
2 wheel drive
75,000 miles
View 4 Replies
I have a 2005 ford f250 super duty 5.4L the problem am having is the other day I took the truck out the yard an parked it across the street. 2 hours later I went back to move it it would not start the engine just kept rolling over I did this for about an hour it still refused to start. 2 days later I tried it again it started without any problems. I put a code reader on it it said P0453 fuel tank pressure sensor. If that is going bad would that cause that problem or would it be another cause.
View 2 Replies
I have a 05 f250 6.0 that currently will not start and no smoke. Replaced batteries and tested ficm. At initial injector buzz voltage drops to 18.8 then jumps back to 48.8 and drops again to 18.8 while cranking. My question is if the voltage is this low does the pcb still just need a resolder or are there components that will need to be replaced?
View 1 Replies
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
View 9 Replies
I have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 Replies
I have a "rattle/knock" that I think is coming from the doors on my 2000 F250 SD extended cab. The rattle is only there when the truck is going over bumps....especially closly spaced bumps. My buddy has the exact truck and it does not rattle.
View 14 Replies
2003 F-250 SD 4x4 w/5.4L engine and 4R100 trans (pic in sig) . Truck has 280K on it with about 40K on a partial rebuild on the top end.
Took the truck out offroading and got about 4" from the top of the 33" tire in water (not mud.. water) . Someone with 6' tractor tore through the puddle.....
Well the truck survived through it ... albeit dirty as all hell and developed some issues soon thereafter. Codes for misfires on cyl 1,3,6,7, general ignition coil, etc etc etc
Power washed the underbody , washed the mud off the engine bay (yeah... with water but given it was caked with mud and water to fill the plug wells... no additional harm) .
Replaced all 8 COP and 4 plugs ( easier ones to reach), oil change, oil filter, new paper cone filter. checked most all the harness connections and cleaned with alcohol also. Reset the PCM/ECU and drove the truck for about 100miles and finally just after putting a full tank of gas (92 Octane) I throw a P0325...
The engine runs very clean, no hesitation, smooth idle, smooth acceleration on both light and hard acceleration. Just the damn code. Is it the gas I just topped off? After 100+ miles with new COP and plugs it threw nothing until this and runs great. Dont hear any knock/ping/detonation by ear and feels silky smooth at idle.
I really dont want to have to tear the intake off to replace bank 1 knock...
View 6 Replies
Pulled into parking lot this morning, 05 F250 CC 4x4 V10, truck starts dinging at me, Park brake light comes on. Ease off of gas and idle around to parking place, no sign of brake drag. Release Park brake, no difference, set the brake and release, no difference, guess the microswitch went bad. Not raining, never hit a bump, MAY have had my foot on the brake, but that shouldn't effect the P Brake.
After setting for the 12 hour shift, all is good and well. Did not come back on.
Where this switch is? Is it under the cover by the foot set or under the truck along the cable? Would like to know where to look next time this comes up. Did have 2 new tires installed on the front a week ago, new tierod and aligned at the same time.
Just wondering and curious, my last F150 had all kinds of electrical germlins in the windshield wiper arm.
View 8 Replies
uper Duty 6.2L ... Alright, the loud cam phaser or fuel injector noise/tap..Is this just a cold weather issue or is this going to be like this all the time under start up? Mine was quiet until now (1200 miles) now under cold start loud knock/tap sound. Seemed to go away when truck warmed up and was idling. Was or Is there any fix to this noise.
View 14 Replies
I have a 06 F250 with a 5.4L truck has 50k on it. I have been reading many articles on the issues with can phaser/cam tensions/cam chain issues. I have noticed that when I start the truck a get a knocking noise that goes away with in 5 sec of the truck starting. I have been noticing lateley if I am sitting still at a light and go to give it gas for a short period I get a sound that sounds like a cam chain slap for a split second as the truck starts to move it goes away. I had a friend of mine stand outside the truck and put in gear and power brake it and as it decelerates you hear a quick cam chain slap. I use Catrol 5-20w standard oil and motor craft oil filter. I purchased the truck with #6k on it 3 years ago I have replaced the leaking exhaust manifold with Gibson stainless unit and have confirmed they are not leaking again. I have heard that the hydrolic cam tensioners sometimes get clogged and people have run a oil additive to clean out clog.
View 14 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
2005 F-250 King Ranch Diesel ... My truck when I got it the 4x4 wouldn't engage. I replace the front inner seals, and the lock outs. Still wouldn't work. Took the shift motor off and freed it up and it worked fin till today. Changed the shift motor and still nothing. This truck has been nothing but problems since I have had it and now this ... Truck is going on the market soon and would sell better if the 4x4 worked ...
View 13 Replies
F-250 2005 XLT 5.4L 4X4. Had ford for a few years now (Escape as a personal vehicle and econoline as business vehicle). Now I'm having a little problem with 4x4. It wont engage. Worked fine last week and now nothing! I did check all the fuses and when i switch to either 4Lo or 4Hi I can hear a clicking sound behind the switch but feel like it's getting blocked or something. Tries a few time then stop...
View 14 Replies
I have had the ABS light on for about a year now. I looked thru the forums and found that the typical reason if a faulty rear VSS (vehicle speed sensor). I found a replacement part online and got it ordered and replaced the original part. Simple 5 minute fix, but it didn't fix it!
Now when I get in and start the truck the ABS light is off, but after I drive off about 20 yards the light comes back on and stays on.
The other day someone stepped out in front of me at a cross walk and I hit the brakes pretty hard and although the truck stopped in time, the rear wheels locked up, so I'm thinking the issue is at the rear.
View 5 Replies
