Ford Super Duty (1999-2016) :: 2006 F250 Auto - Trans Won't Shift Into Overdrive?
Jun 30, 2016
I have a 2006 F250 with the 6.0 PowerStroke and automatic transmission. I just purchased this truck at an auction about a month ago.
Today I notice the transmission is not shifting into overdrive. No warning lights. If I press the tow/haul button in no change but the tow/haul light does come on. If I press it again (to turn it off) the tow/haul light goes out but still the transmission will not shift into overdrive.
This leaves me at about 2000 RPM at 68 MPH. I just had a Ford dealer perform Transmission service last week. (20,000 miles after the last recorded service.)
I am already not happy with the service I received at the dealer so I am really hesitant to take it back to them if it is something not related to the transmission service they performed.
View 5 Replies
Advertisement
I have a '99 F250 SuperDuty Diesel with an Automatic Transmission. There is a button on the end of the gear shift which allows you to turn off overdrive -- in other words the transmission won't shift into overdrive once you press the button.
Here's my problem. I start off driving normally. I've not done nothing to the overdrive button and the truck shifts normally into overdrive. 10-15 minutes down the road, the overdrive light (which indicates the state of the overdrive button) is FLASHING. Pressing the button doesn't stop the flashing. Once this flashing starts, the only thing I notice is a much more abrupt shift from 1 -> 2 gear.
View 14 Replies
I have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 Replies
I have a 2008 for 250 6.4 powerstroke. Issue I am having is occasionally when I shift from drive to reserve it will slam when I shift to reverse. It is an intermittent issue. What causes this and what to do?
View 1 Replies
Only got a click when turning key, in Park or Neutral. Made sure I had >12.4V from battery. Jumped starter solenoid with a remote start switch across main power line to starter and the 's' post, crank pulley almost moved, but didn't rotate. Removed belt, all pulleys rotate, but could not budge the crank pulley with a short breaker bar/socket, rotating clockwise from front. Removed starter, that upper bolt is a super pain! Not even sure I'll get it back in. Jumped starter solenoid again on the bench using a battery and jumpers, not the best connections, starter hesitated little bit, but opened up fully a few times, so I'm thinking it's ok (even though the power line from the solenoid to starter motor needs re-taping). Tried rotating flywheel from starter hole, no good leverage point, but no movement. Before I re-install the starter, how much torque should I be putting on the front crank pulley? Some say it should move easy enough cause the starter isn't that powerful. Others say remove the spark plugs to reduce compression? This truck is new to me, so I unfortunately have no history.
View 1 Replies
My dad has a 2006 F-250 5.4 3v that spun a rod bearing at 107,383 miles. He's never been thrilled with the performance of it (told him he should have gotten the 6.0 when he bought the truck new, but why listen to a 15 yr old ). We've been throwing around a couple different ideas for engine swaps since the 5.4 is dead. We scored a 5.4 2V Lightning engine, but after trying to figure out transmission controllers or if we'd be able to tune the stock PCM for the 2v, we've put the project on hold.
Recently, I've been trying to convince him to do a diesel swap over the L-motor. I have a friend selling a cheap 99 7.3 with trans, PCM, harness, intercooler, piping and other misc stuff. Would that harness generally be plug and play with the body of the 06? Would it be more worthwhile to try to find a 6.0 from 05-07 and swap everything over?
I've also been considering a Cummins swap, although I haven't gone much past looking at complete engines on eBay and Craigslist. Would this be the better route, and just get a standalone controller for the 5R110?
So I'm looking for other's opinions. Should we go 7.3, 6.0 or Cummins? Should we stick with gas over diesel? Try to make the Lightning motor work? Or just go back with a stock 5.4 3V? I should say, he won't sell the truck for whatever reason, so he's not worried about resale or anything. We're in Michigan, so we don't have to worry about emissions. And we're fairly mechanically inclined, so I'm not too worried about doing the swaps, however my knowledge on diesels is limited.
View 4 Replies
1999 5.4 ... I was just driving down road and truck suddenly wouldnt shift into overdrive/higher gear. pulled to side of road and the motor was revving very high at 2500 rpm. shut truck off and on a few times...kept doing it until finally after a while it went back to normal....
View 1 Replies
Tonight i noticed overdrive flashing. No changes in shifting, truck shifted fine. I shut it off when i got home, started back up, light was not blinking, not sure if its like the check engine light and stays on or not. Where light blinks but shifts fine?
View 10 Replies
I recently purchased an 02 F250 v10 4x4 with 150k from a local auto auction. The transmission, for lack of a better term, will "grunt" when going into third and in and out of overdrive. It doesn't seem to slip at all and the fluid looks slightly discolored, but it does not smell burnt. No Torque Converter whine either. A friend of mine who has owned 10+ SDs for his business said I may need to replace the TCM. Not too sure about that, because other than the strange noise, the truck seems to shift normally.
View 5 Replies
I have an '01 F350 super duty dually, 7.3L, auto trans. Over the past weeks my overdrive light on the gearshift would flash intermittently, maybe once every couple weeks. I chalked it up to a prior theft attempt where the steering column was damaged, and had turn signal/hazards issues after that.
Over the past few days my reverse gear has taken longer to engage, and is hard getting into the higher gears at speed. As of yesterday, reverse is out and won't shift out of second. Fluid level is good and clear. Could this be a PCM issue, or some sensor or relay?
View 1 Replies
2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
View 14 Replies
So when I try to kick into 'passing gear' in this '01 f250 5.4l, i get no tranny shift. Whether I'm in tow/haul mode or not.
View 10 Replies
I have a 2007f550 auto trans with a flashing tow/haul light and a code of po791 coming up. Flashing light will clear in k/o position and remain off until placing selector in drive,after two feet or so of travel,an audible clunk and the trans acts like it is in third gear. Reverse is no change and highway will not shift into o.d. The iss "A" is listed as the culprit but ford doesn't list a iss a.
View 2 Replies
Iv got a 2003 6.0 stroke with 212k miles on it. Runs like a top. Done a slew of work from injectors to hpop, 2 alternators, intake, exhaust. NO tuner! Stock. Anyway recently I started the old girl up, warmed up a bit and shifted into reverse and truck did nothing. Went to drive and same thing. Held brake and revved it up and it dropped in gear. Shifts fine after that. No issues other than the occasional NO shift from park problem. Iv dropped pan and replaced all filters recently.
View 2 Replies
The kid at body shop called, he has the cab ready to swap onto the 04 gas job except for the shifter cable at the trans. I have never done one either, and do not know how to take it off. I thought it was like the old trans where it was in a plastic grommet, but the cable almost looks like it is grafted to the trans. How to get the cable off the trans shift arm?
View 2 Replies
After reading the book, I'm afraid I still don't understand. When the hubs are in AUTO, & the shift on the fly selector is turned to 4X4 high, or 4X4 low, is the truck in 4 wheel drive. What happened to free or lock.
View 3 Replies
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
I am changing my 99 f250 4x4 from auto to manual tranny. I am just looking for pics of where the hydro line runs. I don't want line rubbing something and ruining line. Like does line run under the cab wiring harness? Like between wiring and firewall? Where on firewall does reservior get mounted usually? Are the holes all ready there for it that I am not seeing?
View 1 Replies
I just bought a 95 f250 4x4 with the 460. The guy i bought it from had a trans slipping towed it to the shop when the shop went to pull it in they started it put in gear and engine died. The motor is now tight w no movement either direction with a bar obo it. Is it possible the trans is holding the motor tight? What can I do?
View 10 Replies
I recently purchased a 04 f250 with the 6.0l powerstroke. I drove it for about 3 weeks now, Ive put my trailer behind it with small loads and just today tried to use the tow/haul button. When you go to pull out the tranny never shifts from first gear?? Its pulls and runs fine until you push the buttan and no shifting........
View 6 Replies
2009 F250 Super Duty 4X4 auto lock hubs not working. Indicator lights on dash come on but will only go into 4 wheel drive when hubs are locked manually. Vacuum is present at lower of the two vacuum lines when engine is running. I attach the lower line to the module, rotate switch to 4X4 high or low and module doesn't allow vacuum to reach upper nipple. Which fuse operates this module?
View 3 Replies
