Ford Super Duty (1999-2016) :: 2008 F250 - Gauges Stopped Working / No Crank / Security Light Flashing
Oct 31, 2013
My father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
View 10 Replies
Advertisement
I have a 2001 F250, 5.4, 4X4. My ignition key stuck in the start position and when I pulled it back to the run position, everything seemed ok. As I started down the road, my speedometer stopped working and my overdrive light was flashing. Also my turn signals had stopped working and my A/C clutch didn't engage. Figured I burnt a fuse. I looked in both the under dash and power distribution box and all seemed well. I checked the fuse for the turn signals/flasher and it was fine. The flashers worked. Thought I might have fried something so I replaced the ignition lock and switch. Also my service engine light came on throwing a code for the vehicle speed sensor.
Looking for solutions on this forum and the internet, I learned that the turn signal switch could have gone bad and the VSS sensor is on the top of the rear dif and an easy fix. Well replaced the sensor but nothing changed. So I went back to the fuse box. Examined every fuse, big and small and I found a 10a with a small space. This was #24 under the dash. From the manual, "#24, 10A, A/C clutch, Blend Door Actuator, Trailer Tow Battery Charge Relay Coil, Four Wheel Anti-Lock Brake System (4WABS), Turn Signal." Replaced it and everything went back to normal. Turn signals work, A/C clutch works, no flashing overdrive light and speedometer works. All from a 10A fuse. If you have any of these symptoms examine all the fuses carefully. There's a 20A fuse for turn/hazard lamps and this other one buried that's only 10A.
View 1 Replies
I have a 1999 f250 7.3 ... l extended cab 4x4 super duty ... ABS light on, over drive light flashing and speedometer has stopped working .. I have replaced abs senor on the rear of transmission and on the rear end.both new and just replaced abs module just the computer not the pump that was used . And abs light, overdrive light are still on and the speedometer is still not working ..
View 14 Replies
I have a 2000 F350 4x4 with 7.3L diesel and a manual transmission. While driving home yesterday my gauges (fuel, temp, volts, oil pres) stopped working. Within a couple min the speedometer and the tach also stopped working, but the truck was still running fine. Within a couple miles the engine stopped running, just like I had turned the engine off.
After having it towed home I checked all the fuses, none are blown, but there is no power to fuse #16 (15A, instrument cluster, high beam head lamp). Also in the fuse box under the hood, again, no fuses are blown, but fuse #9 (left head lamp low beam) and #11 (right head lamp low beam) have no power to them.
View 3 Replies
2002 F-350SD V10 Automatic. Running down the road with no load or with load. First gauges bottom out, next overspeed light starts flashing, engine goes to 3000 RPM on it's own. Stays that way until I shut off then restart. Sometimes it does this several times in one mile.
Second trick, again driving along, all gauges stay up but engine just stops. Got to set dead for 5 minutes before it will start. The shop says on the first problem this happens: Voltage goes way low then goes way high then everything starts failing. We changed battery but no luck. Got to be down line from battery.
View 6 Replies
So I'll be driving down the road and the gauges will randomly start jumping around then the truck will just shut off, this just started a couple days ago, it seems to be gaining in frequency, when i try and restart the engine all my warning lights flash on and nothing happens, try again and it starts back up, now the last time it happened all of the above happened but it was followed by a fast clicking noise from under the steering column, it has to be a electrical issue as i have full tanks and motor is in tip top shape. Also no codes pop up with my code reader.
View 1 Replies
I have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 Replies
03 f 250 super duty, my battery light came on and when I accelerate my dash gauges shut down and radio turns off, if I idle or stay under twenty MPH, everything works fine. Battery and alternator test good, lights never dim, any thoughts
View 4 Replies
The factory remote start is not working on my 2009 F 250. The red light is lit when I push the button, the doors lock and you can hear something engage in the engine but it does not crank it. If I keep holding the button the alarm starts to go off. When I walk up to truck the radio is on and I need to hit the remote start button to shut everything down before manually staring.
View 4 Replies
2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 Replies
This is a 6.4L powerstroke, but this is not an engine specific problem. I have a no crank condition that appeared overnight while parked in the driveway. I CAN start it by using the solenoid connector wire near the air filter box and supplying 12v from + battery post. I THINK that eliminates batteries, solenoid and starter.
Now that leaves Trans range sensor or (NSS) and the ignition switch. I can test and get 12V (light) on the Blu/Wh wire from ign sw when turned to start, so that seems good. And as far as I can tell the trans range sensor is internal to the tranny, and I really don't want to go there if possible....
Also there are no codes on the Solus scanner I borrowed. And the voltage is showing as 11.7 on the scanner....is that low enough to prevent voltage from being sent to the solenoid thru the SJB and/or PCM even though engine will start as described?
View 14 Replies
I have an F-250 diesel 2004 and about six months ago it started acting really crazy. Basically most all of the dashboard electronics stopped working like the speedometer , odometer, gauges, etc. additionally all of the interior lights, and the radio stopped working. Now it looks a lot like the attached picture when I'm driving the truck. All of the lights are lit up on the dash panel but nothing actually works. I thought at first that a bunch of fuses might be blown but I have replaced nearly every fuse that has anything to do with any of the affected systems. What the issue might be.
View 11 Replies
I have a 2003 F250, 4x4, 5.4L and today my fuel gauge stopped working. I don't know if it had anything to do with a stall, I was on an exit ramp and the truck cut off, I quickly restarted and no issues after that. Other than the fuel gauge not working at this point.
I looked at the fuse panel diagram and there is no fuse for just the fuel gauge. The only thing I see is #35, instrument cluster. The rest of my instruments are working, so what else would cause the fuel gauge to stop working? It had a little over a half of a tank before the stall, after the stall it went down to less than half. I filled up shortly later and it's just stuck at less than half.
View 1 Replies
A buddy of mine has a 99 F250, and the 4WD stopped working. The 4wd light in the dash does not turn on with the key with the rest of the lights. There is a Low Range light that does turn on. He took it to a shop/dealership and they said the vacuum was good. They also swapped in a different GEM module, which didn't change anything.
I swapped the relays under the hood - no change. I keep reading that there is a two wire plug on the transfer case I can test for voltage or to manually power the motor. Where is it? I see two plugs - the blue one on the left has 4 wires, the black one has more. Or is that not the shift motor I need to be looking for?
View 6 Replies
My door locks stopped working new battery in fob, I can hear them trying to work. 2000 f250 crew cab .....
View 3 Replies
All my door locks stopped working in my 2008 F250 Crew Fx4. Locks do not work from a driver or pass. door, key fob, or door keyless pad. When you hit any of the switches you can hear a relay type sound in the SJB.
There was some sort of failure because we could smell it. But I am not sure if it was the SJB that failed or a wire between the SJB and the lock motors.
Looking for a wiring diagram of the door lock circuit? And/or know how to troubleshoot to find the bad wire or if it is the SJB that failed.
View 6 Replies
1998 F-250 LD 4x4 463,000 km.
My truck begins to flash the OD light after driving about 10 km. So I borrowed a friend's scan tool and got a P0503, and P1500. So having been pointed to the vehicle speed sensor, I connected TORQUE and watched closely vehicle speed. Driving at a steady 80 kph it will jump rapidly up and down, from about 72-92, while the gauge in the instrument cluster reads a calm and steady 80.
Which sensor and wiring do I need to inspect? Rear diff or on the back of transfer case? Oh, and the ABS light is NOT on.
Sent from Nexus 4. IB AutoGroup
View 14 Replies
I have an issue with my 2008 f250 6.4 where the gauge cluster is dark and truck won't crank. The only light on the dash is the airbag light. I have tried reprogamming with my Spartan tuner, checked fuses, removed aftermarket alarm, charged batteries. I scanned and got two codes. P1260 theft detected and a u code no comm with cluster.
View 7 Replies
So one day my 4 wheel drive just stopped working, when I put in 4hi nothing same with low, the light on the dash doesn't even pop up and it doesn't engage. I've done about everything I could think of doing besides replacing the motor for it and the wiring, I hate getting stuck...
View 4 Replies
My drivers window will not work at all but when I push the button I get a clicking in the fuse box. The other 3 windows partially work but will only go up or down in small increments. I have tried holding the button and slamming the door and this allows the other 3 windows to work. I thought it was the switch so I replaced it and that was not the problem. Fuse and relay seem to be fine. If it was just the driver window I would think it was the lift motor but with the other 3 windows on the fritz I have no clue.
View 1 Replies
I'm hoping this might be a "quick fix". Got in the truck the other day and my power driver's seat had no function what so ever. Not a big deal for me as I drive with the seat all the way back but the complaints are starting from my wife so it's time to find a fix.
This is the first F250 I've had so the wiring is a little new to me. I checked the fuse panel and the fuse seemed okay I swapped #9 out for #22 as they are both 30A and I don't need the trailer at this time but still no luck.
Are there any other systems tied into the driver's power seat, any wiring harnesses I should check or perhaps a fuse that is not shown in the owner's manual? My truck is the 2013 Gas F250.
View 2 Replies
