Wanted to get feedback if it is a good idea to change the oil the very first time in a new truck sooner to ensure no engine breakin contaminates get in the engine?
I have a new F250 6.2 that I have put 1300 miles on in the last month. First 1k break in, last 300 miles towing 8k. Was thinking of doing the first change at 1500 miles and then every 5000 miles after at that point.
My 2007 f250 power stroke 6.0. My A/C comp went out. After replacing it I was told that my fan clutch is bad and will cause the new ac to go out. My engine is not running hot. The fan still spins for a while after engine is turned off.
1) Could it have not been re installed correctly?
2) How do I know my Fan Clutch is bad?
3) How do I replace it myself?
Its a 2001 f250 with a 5,4. I just recently put a new shot block in it, the short block is a svt short block for an 01 lightning. every thing off old motor went on new svt block just fine, and it drop in just fine. only it will not warm up i let it run for 45 min the other day and on the gauge it would not come past the c. and i do believe the gauge to be accurate because the heat in the cab sucks and the top rad hose is just warm, not as hot as it should be. I've already put 2 new thermostats in it so I don't believe that to be the issue either.
View 14 Replies2001 f250 5.4L v8. Engine temp seems really low. The gauge is reading barely above the cold in normal range. The heater is only blowing out 75 degree air at the warmest. It gets to its normal temperature with in 15 minutes even when its real cold out. I live in Minnesota and its been a really cold winter so having hot heat would be nice. I just bought this truck at the beginning of the winter. Whats going on?
View 14 RepliesWhat are my options for increasing the engine power in my truck? I'd like to see somewhere between 350-450 hp on the rear wheels. Unlike you guys in USA I can't just drop my truck of at any garage and pay them to do this for me as i live in northern Norway and there ar as good as none who work or knows much about american trucks here. I also wonder what power levels can the original transmission handle whiteout reinforcement?
View 14 RepliesOk I rebuilt the engine in my f250 5.4 3v. Timing set cam phasers and oil control valves are new. The problem I'm having that just started after 5k miles on a new engine is all of a sudden i will start getting misfires 1st time it happened said #6 i changed coil same problem came back this time said multiple misfires now I'm just getting #4. When the misfires happen if i hold throttle where it is it will misfire as long as i hold it there if I let off gas then apply right back misfires stop for several miles then will happen again. I have changed fuel pump and fuel pump driver module same problem exist.
View 3 RepliesI have a 2005 F250 with a5.4 engine. When the engine is cold runs fine. When engine gets hot the vehicle shuts down.
View 1 RepliesIs it possible to put a 7.3 ltr from a 1997 van in my 2004 f250.....6.0 has cost me my fair share and would like to swap, 7.3 was giving to me because body is smashed i know engine is good , runs and drives
View 3 RepliesMy question is pretty simple: on my 2016 F250 psd 6.7 I am towing my trailer, using tow/haul mode and I have the engine exhaust brake button pushed.
Suppose I begin going down a long, downhill grade and I want to hold, say 55 mph. How do I actually activate the engine exhaust brake (like they show in this Ford video) to hold me at that speed all the way down?
I tried working slowly up to my desired speed and then tapping the brakes a few times for it to kick in, but it didn't hold me. I also tried tapping and then riding the brakes for 2-4 secs to see if it would kick in, but it did not. To be clear: I *am* in Tow/Haul mode and the engine exhaust brake icons are both lit up in the dash.
Why does my engine fan run when truck is cold? I hate it, anoying winding sound. It will run that way for up to ten miles sometimes. My other trucks never did this. This is the 6.2 gas.
View 7 RepliesI have a 2001 f250 with the 5.4 I replaced the belt because of belt squeal and after replacing it the squeal is gone. now after the truck gets to its normal temp and I stop at a gas station for dip I will leave it running and when I come out it has this loud chirping noise it kinda sounds mechanical but it very well could be something on the belt drive. I am stumped it goes away after I start driving but I am kind of nervous about what it could be.
And the only time I hear it is while the truck is at normal temp and in park I have rolled the windows down and can not hear it while driving or at traffic lights. a part of me says it could be the fan clutch and now that it has a good belt on it I am hearing a sound of maybe the clutch going out or a pulley bearing starting to go out. Where I should go from here?
I have a ford f250 1997 with a 5. 4 triton engine in I bought a 02. 5.4. Out if a ford expedition he said it would fit but my mechanic is not sure . Would the engine out if the 02 fit in the 1997 and what would need to be done.
View 7 RepliesI have a 2006 f-250 powerstroke with 97000 on it egr delete exhaust and a h and s xrt pro on it. The pickup will always start when the engine and oil is cool, but once i run it for a while it and the oil gets warm it wont start back up again. I then have to leave it sit for a while and it will start. The engine just cranks but does not fire. I have replaced the dummy plugs on both sides and all the injector o rings on the passenger side. Some mechanic friends of min have had same problemed 6.0 liters and replaced these and it has fixed the problems I do not think it my high pressure pump.
View 2 RepliesI've got a 2004 f250 4x4 crew cab that is driving me nuts. It runs great, but sporadically it will just quit running. Tach drops to zero. Engine is still turning, because it usually restarts by itself as long as I am moving over about 45. If not I can pull over, put it in park and restart it. Sometimes it sets codes, never the same ones and usually not something even related to the problem (transfer case solenoid for example). Most times it doesn't set any codes. I have changed the plugs and coil packs on all cylinders. Right now it is showing the P1000 code so I am suspicious of the pcm or the wiring to it. I think the tach is the only thing dropping out on the instruments and all the instruments are powered through the pcm.
View 3 RepliesI have a 2005 ford f250 super duty 5.4L the problem am having is the other day I took the truck out the yard an parked it across the street. 2 hours later I went back to move it it would not start the engine just kept rolling over I did this for about an hour it still refused to start. 2 days later I tried it again it started without any problems. I put a code reader on it it said P0453 fuel tank pressure sensor. If that is going bad would that cause that problem or would it be another cause.
View 2 RepliesI have an 2001 F-250 5.4L.
It has the Triton engine and the problem with spark plugs blowing out. I have a kit with thick inserts that I'm going to install. I need to drill and tap the heads, but first I need to get the piston in the cylinder I'm working on to get close to the bottom and have all the valves shut. But I can't manually turn the engine over. I tried using a long ratchet with a socket that fits the nut on the crankshaft pully, but the nut just seems to tighten more, instead of turning the engine over.
And trying to turn the fan pulley doesn't do it either. Also, using the electric start for a split second at a time still seems to turn the engine over too quickly for me to get the piston where I need it. Do I need to pull all the spark plugs to do this? I really just wanted to work on one cylinder for now, instead of opening up a can of worms.
Bolts breaking on the exhaust manifold. If so why isn't ford doing a recall on this problem I have a F350 V10 90K miles and 3 on the top drivers side are missing not sure on the passenger side. Is this a problem with all the ford engines I have never had this problem with any other truck or car I have owned.
View 5 Replies2014 F250 SuperDuty 6.2L gasser, x-cab long bed work truck. 105k miles, original owner, 1 driver, mostly highway miles, well maintained and super clean truck.
First issue occurred at 83k miles, Aug 2016. Warm summer day climbing I-70 in CO, slightly loaded, and just entered the Eisenhower tunnel (11,150' altitude). Lost power, no RPMs - not running, I put it in N and rolled as far as I could. Hazards on and no-where to pull over, hugging the wall and blocking one lane. Power OK - will crank, no fire. 1/3 tank on the fuel gauge and >100 miles distance to empty on the trip computer. Tunnel rescue shut down traffic and pushed me out into the daylight.
After waiting an hour to fill our paper work for disabling the interstate tunnel I returned to the truck which quickly started. No symptoms, no lights, no codes. Topped off the fuel tank after a easy 15 mile drive downhill. Drove another 800 miles symptom free to my destination and checked it in at the dealer. At this time a check engine light had finally illuminated - PO420. I shared the story of stalling out at highway speeds with the Service Writer. Dealer replaced the cats, confirmed fuel pressure OK, computer condition OK, serviced the trans (at my request).
No symptoms reoccurred during the next 20k miles until last weekend. 105k on the OD now. Heading to Flagstaff, AZ on I-40 in similar conditions. Hot, AC running, climbing in elevation, slightly loaded, running on the bottom 1/3 of the fuel tank... Died while cruising at 79 mph. Well, at least this time I wasn't in a tunnel and had a shoulder to pull off on. Deja-Vu - full power, radio on, no engine lights, gauges normal, fuel reads over 1/4 tank, >100 miles till empty on the trip computer - won't start. Cranks, but no fire. Some sputtering during start attempts must have triggered the next trouble code.
Opened the hood, removed the gas cap, let it vent and cool for about 30-40 mins while I took a walk. Returned to the truck which easily started and let me drive to the next fuel station, 30 miles away. This time the check engine light stayed illuminated. It took 24 gals of fuel. Drove 3 more hours and almost 200 miles without symptoms - check engine light still illuminated keeping me curious and fully alert along the way.
Got the codes pulled at a parts store that was open on Sunday. PO300 & PO301. Random misfires and cylinder 1 misfires. Sounds consistent with poor fuel supply? Spent the rest of the day searching forums for any clue to this highway stalling. All I came up with was to clear the computer - disconnect battery, turn lights on, wait 15 mins, reconnect battery, start engine, apply brake, drive, etc. This and another full tank of gas gave me enough courage to set out on my trip home.
Next occurrence was just outside of Santa Fe, NM. Similar conditions again: Hot day, AC kicking, Interstate travelling about 80mph, slightly loaded, climbing in elevation, fuel tank just below half - stalled out. Repeat previous learned routine. Open hood, vent gas cap, walk it off for 30 mins, return to truck, start it up. Drive to next town and top off with fuel about 30 miles away - only took 16 gals! Made it home 4 hours later without stopping. No repeat symptoms, no check engine lights.
The next day a code - PO420. Catalytic efficiency below threshold.
Quick recap:
6.2L gas engine stalling at hwy speeds.
Cruising between 65-80mph
-Interstate travel - no stops between last fillup and stall.
-Warm weather, AC on
-Running on bottom ~1/2 tank
-climbing in elevation, slightly loaded
To clarify: slightly loaded - no trailer, maybe 1,500 lbs bed cargo, mostly wind drag. The most I have pumped into the fuel tank is 29-30 gals or so. I assume I have the 34 or 35 gal tank. Never seen the calculated "distance to empty" below 40 miles.
I replaced the head gaskets on a 2006 F250 6.0 Diesel, put it all back together and started it up. It ran great for a lil bit, then it started cutting out. It did this for about an hour then I killed it and it took a little bit to restart it, spinning over and over to get it to run, this took place several times. The engine died and now it will not start. I keep getting codes P2284 and P2290. What could be causing this problem??
View 9 RepliesI drive a 2000 F250 5.4L. Currently has about 168,000 miles on it. I changed the oil the other day and cleaned the air filter. I used what I usually use on the oil change which has never been a problem. But this is first time to clean the K&N filter. A day or so later my engine is making a loud air rushing noise. Under throttle the engine compartment sounds like a wind tunnel. At 3500ish rpms it makes a harsh whistle noise. The air rushing noise doesn't go away once its warmed up or after the engine has been cool. Noise didn't go away with the filter being taken off either.
Could all of this be caused by cleaning and not using k&n air filter oil (but rather WD40 upon Dad's suggestion)? Or is there something else going on?
Just noticed a ticking sound coming from my engine... just turned 160,000. Hoping nothing serious...
View 11 Replies