just bought this f250 seems to walk on the road alot, had it looked at has new balljoints, he says everything seems tight except there is lots of play at the gearbox, is it recommended to have it rebuilt or buy a reman, was told that even the reman seems to be the same way
View 14 RepliesMy 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
I replaced my steering gearbox with a remanufactured oem gearbox (no, not the redhead. I wish I'd had the extra money but I didn't.) I replaced the factory sway bar (1.25" diameter) with the Excursion sway bar that came on my axle (1.4" diameter) along with polyurethane bushings and greaseable end links. I replaced wheel bearings, ball joints, track bar bushings, tierods (ends, sleeves, the whole nine yards). Literally everything from the gearbox down, besides the pitman arm, is brand new.
The next day I took it in and got it aligned at Goodyear. The steering is noticeably more responsive, but I still have 1-2" of play either way before I get a response. I'm skeptical about tightening the gearbox. I did that on the old one and it improved steering for a couple years, but this new one shouldn't require any tightening.
I have yet to install new steering stabilizers, but I can recognize bump steer versus this problem on a straight, smooth road. I'm sure the stabilizers won't change the 2 inches of play.
My 2010 6.4 F250 seems has a loose steering wheel. The steering of the truck hasn't changed nor has there been uneven wear on the tires. It doesn't drift if I let the steering wheel go. Had the front end inspected and was told it's all good under there.
YET, my actual steering wheel is loose. I can grab the wheel and wiggle it front to back and side to side. It FEELS like the bolts that hold the steering wheel to the column are loose. What was the cause/repair? Is this something I can repair myself or a local shop? Or is this a dealer fix?
I have a F250 SD with a 6.0 diesel. My steering wheel is loose. I tested and know for sure is not a problem inside the cabin. Fallow the line thru the linkage to the steering box by the left front wheel. I found an adjustable switch there. Just on top of the steering box. It has a lock nut that must be loosen to adjust what it looks like a hex. Very hard to reach. I have watch some Youtube videos but on different vehicles.
View 1 RepliesI've got an 04 f250 4x4 crew cab. I just replaced the upper and lower ball joints on both sides and also the drag link. My alignment was off from the bad ball joints so I had it aligned after I did all of this. Now the steering is really weird. Its like something is to tight. I can barely keep the truck straight because every time I barely move the wheel I seem to be going one way or another and getting it straight is nearly impossible to the point I look like a drunk driver. I can turn the wheel to go around a curve and let go of it and it will stay that way until I turn it back. It won't return itself. I'm kind of lost.
View 3 RepliesI have a 2004 superduty 250 4x4 with the 6.0. I am having a violent shake in the steering wheel mostly and can feel it in throttle at about 45 to 60 and at 72 there is s growel. Have changed tires, wheels checked all ball joints tie rods wheel bearings ujoints. Don't matter brakes on or off, od on or off nothing changes it. I really don't know what else to check.
View 10 RepliesI had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
So I have a 2005 f250 Super Duty 6.0 diesel it is the xlt with leather. So I don't much care for the steering wheels on this truck so i purchase a 05 f150 steering wheel. The splines and everything match up but the plug for the cruise control does not, need a wiring diagram or have done the swap and can tell me what wires connect where.
View 1 Replies2004 F250 SuperDuty 6.0L Diesel. The turn signal (left or right), it would make a buzzing noise, so I located the relay under the steering wheel (by putting my hand on it and seeing which one was buzzing) and replaced it, I bought a replacement at Schucks, then the buzzing noise went away, and the clicking noise is back.
But.... I don't see the turn signal lights in the dashboard and the turn lights are not working, I checked, what could be the problem ? I read the owners manual, in the fuse box under the steering wheel, fuze #18 is used for turn lights, but it is not blown.
I found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 RepliesI have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 RepliesBought a new touchscreen head unit to put in my 06 lariat f250. I have all the controls on my steering wheel for heat and radio and I don't want to lose them with a new radio. This head unit does not have the 3.5mm jack for the axxes unit but has 3 wires labeled swc1 swc2 and swc ground. It supposedly has the converter built in. any views on using a headunit with these wires?
View 3 RepliesIs there a steering stabilizer for a 92 Ford F-250 custom 2wd? and what's the difference between a f250 custom and a f250 heavy duty?
View 2 RepliesI just purchased a 99 F250 Superduty 4x4. Very low mileage (63000). Everything on this truck is great except the steering. I flat towed a 73 VW Bug about 100 miles and it was the most white knuckle drive of my life. Couldn't take both hands off the wheel without the whole truck starting to wander all over the road.
Before I take it in to have the alignment checked and get told that every single part under the front of the truck needs to be replaced, I'm wondering if this is a "common" problem with this truck that others have encountered. One person has already told me to just replace the front hub assemblies, the tie rods, and the steering gear box and all will be well.
I'm hoping all those parts don't actually need to be replaced - especially since there are only 63K miles on the truck. Tie rods seem solid with no play. Not sure about steering gear or unit bearings.
the mechanism that locks the steering wheel is stuck. not the ignition key cylinder (already removed that). how do I release that mechanism to free the steering wheel.
View 3 RepliesI have a 01 f250, owned it for about 8 months now. Have done a ton of work to it, replacing all worn out parts. It's a v10, replaced so far is ball joints, all tie rods, steering dampener, front sway bar links and bushings and Monroe gas Magnum shocks all around. My biggest problem is the wandering in steering. I put a 2.5" add leaf spring pack to front when I first bought it. It has stock bullet whole wheels and new Firestone's destination a/ts. Also. Tires have been rebalanced and are smooth until I get to 60+mph, its a swirling ride after 60mph. Could I have bad wheel hubs or do I have an alignment issue? Planning to replace hubs with Napa hubs since I did everything else and I'm sure there bad with 236k miles on truck.
View 8 RepliesI have a few F-250's that have been having steering problems. and they all have the same symptoms.
When taking a long slow curve, the steering wheel will jump back like 6 inches, as if the pressure is going out. like say you had the vehicle turned to about 10 oclock, the wheel would go back and forth between 10 and 11. However, you do not loose much of your turning. It just has more pressure against your hand as if the power steering goes out.
You can also do it a standing stop. Only when you turn your wheel like say to 9, you can just use a finger to hold it there and it will bounce up and down? I have asked the local Dealership, and their answer was "there is something wrong with the power steering." couldn't get much more vague than that I guess.
I have looked for leaks, none. Checked struts, not bent. Checked tires, all brand new and balanced. Checked steering wheel mounts, all good to go... ???? Just lost...
My 2001 F250 2WD does not have the steering damper that my 2004 F250 2WD has. Is that normal or is my 2001 missing it?
View 1 Replies05 F250 4x4 6.0... Lately, I have noticed a little stiffness in my steering. Mainly when I turn left - it just feels like the truck doesn't want to come back to center like it should...almost like a tire is low on air (they're not - I checked) or a tire has laid over.
I have checked power steering fluid and looked at all bushings underneath. Any chance that the steering stabilizer could be causing this issue? Also...do these trucks not have any grease fittings in the front end? I have looked twice and still haven't found any (in my defense, I haven't had the truck very long)...
My 2002 250 just got ball joints, bushings, sway arms, 4 wheel alignment and new tires to top it all off. Did All this to correct the shakes, shimmies, popping and grinding in the front end. Now they say I need a steering stabilizer up front. Does any other than ford make a bolt on one and haw much and where can I get one.
View 10 Replies