I think I have a clamp or something loose as i am dripping coolant from a black and silver hose/pipe on teh drivers side of the motor.
I can't see any clamps, well clamps i can recognize. how is this black pipe connected to the aluminum pipe? at that seam is where it's leaking.
I have a early 99 7.3, I have parked it for the winter an I had moved the truck the other day an have noticed it had leaked some oil, after looking for the source I found that it is leaking out of the #7 cylinder exhaust port. I know the oil is forsure in the manifolds usually burns off but now that it is not getting to operating temp it is staying a liquid. Where is this oil coming from?!!
View 4 RepliesWhats the best way to get at the driver side exhaust manifold? I have a leak and its tough to get at. Should I remove the tire and inner wheel well?
View 1 RepliesThe doors on my 2005 crew cab are leaking water. Its happened once before, I fixed it by resetting the main seal around the doors. Now this tropical storm had them leaking again. The rear doors are leaking from the top and getting the head liner wet, and the front left door is leaking a little bit onto the middle pillar Guage and down onto my leg.
Is it time for new door seals? My 01 has never had this problem so im not entirely sure what to do.
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
My grandfathers 99 F350, started suddenly, do not know if it was while sitting or while driving. Its more of a stream than anything else. Coming from the rear, cannot see where, appears to be toward the vee of the engine, not inside the bellhousing. The firewall insulation is damp from coolant. Doesnt start until engine starts warming up.
Is there something commonly replaced back there? Didnt want to yank the intake in 20* weather for exploratory surgery. Is not the heater hoses. Idk if the EGRs are cooled on these, thats about my only idea other than freeze plug, coolant tests good down to -20ish, hasnt been below zero in weeks (prior to leak). Not familiar with any of the modular engines.
I'm a total beginner and am slowly nursing an '87 F350 7.5L back to running condition as a plow/farm truck. It regularly loses coolant, even on very short trips around the farm and I figured that radiator needed to be replaced. Today I was hooking a snow plow up and had it running for about 15 minutes when light grey smoke started to come out of the vents in the cab. Looking at the engine, I noticed a lot of coolant leaking out from below the heater housing. The coolant was dripping out of what looks like a protruding bit of pipe a where a hose should be attached. What am I looking at here?
View 4 RepliesI recently did the water pump and hoses due to seeping around the water pump gasket. While there, I decided to replace the overflow reservoir as well - old and slightly discolored. I'm now on my 3rd overflow reservoir - they are all leaking at the front seam. I don't think I have a blown headgasket or injector issues - no signs of white smoke ever, and there isn't any oil or fuel in the coolant. I've also tried a new cap, but it's starting to leak before I build any noticeable pressure - I can back off on the cap and don't get much pressure released. So - just bad luck on parts from Ford? All were OEM from different Ford dealers.
Pics - hard to see on here but go to Imgur to zoom in. [URL] ...
1999 F350 7.3 CCLB Dually. Stock except for DP Tuner and Gauges.
Having some coolant leaking from the EGR unit in my 2011 super duty.. Dealer says it's a 14 dollar part, but labor is a few hours to replace.. Not sure I see how that can be, but I wanted to ask on Here to see how long this should take..
View 1 RepliesI just bought a 2000 F250 SD 6.8 v10 and its mixing coolant in the block and leaking oil. I'm debating on just dropping a newer v10 in it but im just not 100% sure that this engine is shot. It runs great when there's oil in it and I can't even tell there's any problems going on for well over a couple hours after i fill it up with oil.
View 8 RepliesMy truck is a 2005 6.0 with no after mods and has 73000 miles on it. It began to blow white smoke out exhaust. I changed out the egr valve and cooler. After putting back together it then blew white smoke ran it to clear out. This worked however once it warmed up it began to blow thick white smoke at 20 mph and clears up by the time it reached 30mph and white smoke shoots out at rapid acceleration. As well there is coolant leaking out under the truck from somewhere in the motor about in the center. I am looking to work on this myself as I have heard of owners taking it to shops and paying a lot of money for the prob to not get fixed.
View 7 RepliesI have a 2013 f250 6.2, I bought the truck brand new only have about 3000 miles on it and the other day I noticed that the drivers side front is lower then the passengers side front, the drivers side is about one inch lower, this doesn't seem right, also my drivers side front wheel seems to be pushed forward about one inch to the bumper that also doesn't seem right.
View 3 RepliesHave my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
Alright, after finally fixing my 4X4 issues, now I have a coolant leak. It's on the passenger side, just above the exhaust downpipe. I can't find any leaks in the hoses, and as far as I can see it looks like it's coming out of the back of the head and running down the back of the block. The odd thing is there's no oil in it, and no coolant in my oil (which obviously is a good thing), but I don't want it to get to that point of it is getting worse. Heat works fine, and it isn't overheating, only losing maybe a gallon a month. At some point the ford gold stuff was flushed and it has the compatible green, that is the only thing I can tell is not stock. I don't want to tear it down if I don't absolutely have to.
View 7 RepliesOn the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 RepliesI have a 2005 f250 5.4 no mods. its got 120k and needs a wake up. the passengers side exhaust manifold is leaking to the point of fixing and would like to get some input before the big purchase. my question is, headers or new manifold, and what brands is preferred for both I really don't prefer one or the other i just want the best fix really. Changing coil pack and getting more performance out of them and if so what brand. I would like a boost in lower end acceleration and throttle response, like a programmer or such. and if so what brand once again.
View 10 RepliesHere's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
My 2000 f350 is leaking oil from a bolt on the passengers side valve cover. it is one of the bolts on top of the valve cover. Can I just remove the bolt and put a rubber washer under it or do I need a new valve cover?
View 2 RepliesI have a 2005 F350 XL Heavy Duty 6.0L truck that has 68,XXX miles. I recently changed the rear brake pads and about a week later the rear passenger side is leaking brake fluid. The fluid is slowly dripping from the bottom caliper bolt but i am not sure if there are seals in this area. the driver side is fine and the fluid is only leaking from the bottom caliper bolt not the top.
View 2 Replies