Ford Super Duty (1999-2016) :: Shaking And Grinding From Front Driver Side Of Truck
Apr 10, 2017
My truck has an intermittent shake with a grinding/binding kind of noise. It seems to happen at lower speeds, generally when slowing down and turning. When I apply the brakes or speed up it seems to stop the noise.
The rubber/plastic seal on the back of the wheel hub is loose on both drivers and passenger side but I don't think that is the problem. I'm wondering if it is the u-joints or something.
The brakes look shiny and i don't see any scratches on them so I don't think there is a rock or something in there. I have the wheel hubs in the auto setting, and it is a 4x4. The truck is a early 99 7.3L with a leveling kit and 230k miles.
View 4 Replies
Advertisement
2001 f350 4x4 dually 7.3 powerstroke, I recently replaced the hub assembly, stub shaft and seal, u joint, ball joints on the front drivers side and now periodically the truck makes a grinding growling vibration coming from front drivers side and stops after hitting a bump...
View 3 Replies
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Replies
I have a 2013 f250 6.2, I bought the truck brand new only have about 3000 miles on it and the other day I noticed that the drivers side front is lower then the passengers side front, the drivers side is about one inch lower, this doesn't seem right, also my drivers side front wheel seems to be pushed forward about one inch to the bumper that also doesn't seem right.
View 3 Replies
Have a 02 v10 125xxx miles have had grinding noise on drivers side sounds like driving on rumble strip took out the unit hub everything looks good changed out the needle bearing because it was frozen still have sound after needle bearing replacement sound goes away if hubs are locked so question is it the unit bearing or stub shaft...
View 2 Replies
The used 2004 F-350 I bought has developed a driver's side front end howl between 45 and 60 mph over the last 1000 miles. I tried all the standard stuff, rebalanced tires, rotated tires, put on a set of tires from a friend's F-350, replaced wheel bearings, replaced ball joints and nothing has worked.
View 7 Replies
2011 f250 6.2. put it in the shop to have the rotors turned, and front brakes while they were under there. Now it pulls to the right whenever you apply the brakes. Can smell brakes on the left front after a short drive time. Replaced that caliper and it's still doing the same thing. I'm stumped at this point.
View 9 Replies
Truck is 2007 6.0L 4 door F-250 FX4
So this started after some High water encounters around my area. All freshwater. Went to the store and then i notice the truck pulling Left and got home and checked brake temps and the driver front and rear were over 400*F passenger side was 150* or less. No trailer no load in the bed. I decided to clean everything. Pads are worn but still have life.
Rotors showed some signs of where the pad is dragging Not bad though just a small area close to the top hat. I cleaned pads, carriage, and clips and reinstalled everything with some anti seize on the edges of the pads where the clips are and at the same spots on the carriage.
Thought it was ok but the after more water and a day or two sitting the same thing happened again. It is only the drivers side and it's both front and rear. I am stumped on this one. Two calipers going bad at once? I need to tow a boat on Monday So I have got to fix this.
View 1 Replies
What this might be? (see pic)....
View 14 Replies
I've got a 02 SD v10 4x4 with Warn hubs and 97k. Bought it a couple months ago and I've noticed a vibration coming from the front driver side. Symptoms are that of a bad wheel bearing; vibration that increases with speed and not RPM, seems to lessen on left handed turns (weight transfers from driver side to passenger side) and gets worse on right turns. Also the truck seems very twitchy and hard to keep straight on the highway.
Snowed the other day so I locked in my warns (just in case) and I instantly noticed the noise and vibration almost went away entirely except for on the freeway around 70+ mph. Also noticed it seems less "Twitchy" on the freeway. Mind you the hubs are locked in but still in 2wd. After doing a little bit of reading some were saying this is a sign of bad needle bearings and not the entire hub.
I haven't jacked up the tire and checked typical movement in a bad wheel bearing. I know my way around vehicles and 4x4's pretty well...
View 3 Replies
Is there a way to change the bulb without removing the grill and headlight? Seems like a lot of work to replace a bulb. 2013 F350....
View 3 Replies
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 Replies
Cat like noises coming from front driver side tire .. honestly sounds like a cat ..it gets louder the faster I go ... what it could be ?
View 7 Replies
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 Replies
here's the problem. The driver side front power window will only go down and not up. I checked the motor and the master switch with a multimeter and both work just fine. the motor is receiving power and the master switch is sending power. However when i plug the motor back in and re-install it, the window will not go up. Is there some sort of relay that might have gone bad that is not letting the motor raise the window up???
View 5 Replies
Had the death wobble a couple of months ago. Changed all shocks, steering stabilizer to bilsteins; new tires (stock), ready lift stabilizer(stock, no lift) had it digitally aligned. All was perfect. Until my new intermittent steering issues. It appears to happen when making a 90 degree turn, say a right or left onto a perpendicular roadway. As truck straightens out, you'd think the front drivers side wheel is going to fall off(you'd think the lugs are missing).
Pull int a parking lot, drive in a few circles, and all back to normal. Can't replicate every time, force for s few days with no issues, then it might happen again. Other intermittent issue is sometimes, again out of no where, truck will pull and track to the right or left. Pull the steering wheel the opposite direction, it'll track the other way. Again, pull int parking lot, do a few figure eight circles and back to normal. Alignment shop and regular mechanic say everything is tight, ball joint look fine.
View 3 Replies
09 F350 with 50,000 miles, just starting to hear a mild squeak from front drivers side hub I believe. Can hear it while in 4 wheel drive, my thoughts is that the original universal in the hub is beginning to give up. My question is how long would you think I have before I need to get this done? Would this be a warranty item? I am not sure anymore.
View 2 Replies
I replaced my my front hub assemblies on my 2003 F250, 4x4, about two years ago and my driver side hub is leaking. I first noticed it the other day when I tried to shift into 4 wheel drive and my hubs would not lock in the ESOF system.
I used a vacuum pump and it leaked down pretty fast so I assume the knuckle/axle seal is the culprit.
I plan on ordering these three seals:
Amazon.com: f81z-1s175-hca
I am also noticing another # for the axle seal. It is 3C3Z-3254-CA. Which is correct for my 2003?
Are my questions would I actually need to replace all three? The dust seal is not leaking at the moment. Should I go ahead and replace it anyway?
What type of grease do I need to use the seals? I have some disc brake bearing lithium grease in the cabinet. Will this work or do I need to get a specific type
Lastly, I've seen a post where members have made their seal seating tool out of the galvanized pipe, cap, and a flange. The flange is said to be too large and it would have to be ground down for the right diameter.
View 14 Replies
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 Replies
The doors on my 2005 crew cab are leaking water. Its happened once before, I fixed it by resetting the main seal around the doors. Now this tropical storm had them leaking again. The rear doors are leaking from the top and getting the head liner wet, and the front left door is leaking a little bit onto the middle pillar Guage and down onto my leg.
Is it time for new door seals? My 01 has never had this problem so im not entirely sure what to do.
View 3 Replies
My front driver side wheel is making a clunk noise when I hit a bump. I replaced the wheel bearing hub assembly and discovered both axle seals were bad.
View 10 Replies
