Ford Wiring/Electrical :: 2003 - Instrument Panel / Interior Lights / Windows / Radio All Not Working
May 10, 2013
For about 3 months, my wife's 2003 explorer has had a bad door sensor (I'm guessing). The car claims a door is ajar and the alarm would go off randomly if it's locked. Yesterday the battery died because apparently the alarm had been going off for so long while she was at work. After having a stranger jump it, she has had major problems:
-She claimed the headlights didn't work in any setting except in the on position with high beams on, but now they seem to work.
-The instrument panel is totally out including all gauges and all lights
-the power windows don't work
-the radio won't turn on or show any display
-the interior lights won't turn on
All of the fuses are fine and my mechanic checked them as well. He did say that a few key fuses aren't getting any power to them on either side. But the battery is charging and drawing just fine. The car doesn't seem to have any other issues and all of the flashers work just fine.
What the problem could be? I have wondered if one of the relays is busted.
View 3 Replies
Advertisement
03 F250 Instrument panel does not work. Have checked all fuses with a meter. Have already fixed broken wires from the OD button on shifter handle. and also the alternator is not charging. I need wiring diagram that shows the wires coming out the back of the fuse box so I can see if the fuse holder is burned out......
View 8 Replies
I have a 2008 Ford F-150 xlt with stock instrument cluster. I need a new instrument cluster due to my interior lights coming on while driving. I would like to make it look better and not go stock. Id like to have digital shift screen and good looking LED's. What all are my options?
View 2 Replies
My radio, all gauges and windows aren't working. Fuse 17 did not seem blown but I changed it anyway and still no luck.
View 2 Replies
I pumped gas at the local Chevron after noticing I was running just below a quarter tank this morning and immediately after turning the truck back on the instrument panel was dead. All other electric components worked fine (windows, headlights, signals, radio, etc.) Yukon GMC 2003 110k miles...
View 8 Replies
So I know these posts a a dime a dozen but unlike most i know what did to cause the lights to go out.
I unplugged the dimmer switch harness and headlight switch harness to clean the air vents. When i plugged everything back in, none of the red or blue backlighting turns on when i turn the headlight switch. The instrument cluster and all the trim remains dark.
At first my turn signals were not working but they have begun working again. headlights and break lights all work. and my interior dome lights work.
I checked every fuse i could think of that would relate to the interior lighting and everything looks fine there. is there something else i can check?
View 1 Replies
I was replacing the dome light in my 06 Ford F350. I tested the light and it worked then while screwing it back in, the lights when out and then the radio. I suspect it may be a fuse, but have yet to find the culprit.
View 2 Replies
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
View 6 Replies
I have a 2003 F550 6L diesel flatbed truck. Last week, the overdrive button would activate by itself. I'm assuming there was a loose wire so I taped the button to keep the overdrive off. Two days later, the overdrive came on while the button was pressed in and then smoke came out of the steering column/lever area. I pulled over and turned off the truck. The smoke stopped after 10 seconds and I restarted the truck. The overdrive light/functionality no longer worked and the instrument cluster also wasn't working.
The next day I was driving, and the truck died at a stoplight. I got it towed home, and opened the steering column and noticed that the overdrive button wire had burned. I removed the harness clip and charged the batteries. It started but the instrument cluster still didn't work. 2 minutes later the truck died. I replaced the alternator but still it won't charge the batteries. The truck dies 2 mins after getting a battery boost to start the truck. The instrument cluster also doesn't work. What could be causing this issue?
View 10 Replies
I have 2010 f350 and everything works while key is turned on. When you crank the truck I lose power to windows, radio, mirrors, blinkers and instrument panel. When I drive the truck and give it gas everything works. Let off the gas and I lose everything. Sometimes after about 20 minutes of hey driving it will stay on. Also when first starting the truck the gear selector won't let you out it in gear. After about 30 seconds it will go
View 1 Replies
Yesterday I ran my batteries down and had to have my 2003 F350 jump started. The truck started find, and the battery is retaining its charge, but after the jump i lost my power windows, instrument panel (speedometer, gauges, odometer), dome lights, radio, and power mirrors. I have checked all the blade fuses and they are all fine. I have noticed in the past that occasionally it takes a few seconds for these things to come on line after I start up, but this was very rare and the functions always came on line shortly. What the problem could be?
View 3 Replies
Are there any fuses or relays that I could look for besides what the owners manual calls out? Haynes manual is useless w/this problem also. Everything else seems to work fine. Haven't tried the AC or heat, but my gauges, pwr locks and mirrors are all fine. I'm stuck w/the windows down and no tunes.
View 3 Replies
My 2003 Dodge Caravan instrument and radio/heater lights stopped working. I don't see any bad fuses or fusible links. Odometer and other service lights work fine.
View 1 Replies
My hazard, reverse don't work. The over all instruments panel light doesn't light up (the small bulbs work). Gauges with needles work. I'm putting every thing back into the truck. I left the steering wheel resting on the floor while cleaning and also left the wiring in. Everything else came out because I had to clean out the smell of mice. After I installed the instrument panel I started the truck, there was no hazard lights. I checked all the fuses under the dash. I checked all the fuses under the hood.
I did have a bent brake plug blade to bend straight. I need to replace a bad key cylinder, you can turn it without a key. I believe there were three plugs I unplug to lower the steering wheel. Park brake, brake pedal and a plug under the steering wheel. Wipers, interior ceiling light work. I believe there's a switch on the column (?) that includes the wiper arm. Should it also operate the hazard lights ? The steering column is installed, I can drive it around. Outside cargo lights won't go off, even with the light switch pushed in. Everything worked before.
View 7 Replies
I have a 2000 F350 7.3. I started out with my batteries dying after a few days of sitting. I found the interior lights were coming on dimly, and the relay buzzing. great, got it. I pulled the fuse and ordered the dimmer/light switch. I came back next week and the batteries are dead again. Charged them, drove the truck, and then the radio starts coming on without the key on. Pulled the radio.
Next day the truck starts fine, but now the seatbelt noid is going off all the time and the tranny overdrive is blinking "off" but still shifts fine, and goes into overdrive. The speedometer also works erratically... I read a post about the marker lights leaking, I looked and that's a definite possibility. My question is are all these related back to the GEM or BCM? or more problems?
View 11 Replies
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 Replies
1997 Ford Expedition 4x4
When I push the switch for the drivers window I can hear the relay in the fuse block make a click but window doesn't move. If I push the switch for any other window (on the drivers door or any other door) no click at the relay and no window movement. I've swapped the relay with other relays in the fuse block but nothing changed.
I've tested the driver side window motor by running 12 volts directly and the motor works fine. When I press the PDL switch I hear a buzzing sound coming from the passenger floor area behind the glove box but the locks do not go up or down. I started the truck and when I put it in gear I can hear the PW relay in the fuse block clicking repeatedly. Put the truck in Park & the clicking stops.
I was told (on another forum) that the problem is most likely my GEM module. Bought a used 1 on eBay and installed it today but nothing changed.
View 7 Replies
I have a 2000 E150 (Glavel Conversion) van and the interior lights do not illuminate when the doors are opened, although they used to. They also no longer turn on from the headlight dimmer switch. They will turn on individually if the manual switch at each light is pressed while the engine is running, so the bulbs and wiring appear to be working. I replaced the headlight switch with no noticeable effect. Is there a timing circuit that switches these on for a short period of time to allow illuminated entry that could have failed? If so, where would I find the module and how would I test? Relays and fuses look good.
View 1 Replies
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
View 10 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
My instrument panel lights are out are they hard to change ? the truck is a 1997 f-150 4x4 /4.6 liter...
View 14 Replies
