My tail lights parking lights and dash board lights stop working my turning signals work my brake lights work and my headlights work fine I checked all fuses are good I even switched out the headlight switch with a new one and nothing. What can this problem be?
View 14 RepliesI have a 2000 Ford F250 lariat 7.3 .... This vehicle has an aftermarket double din stereo pillar gauges for Pyro meter and transmission temp and has also had a snowplow attached but since re moved since I purchased it. It also has H ID headlights, which are run by the passenger side headlight connection.
The problem I'm having is that whenever I turn on the parking lights it is blowing the number eight fuse under the hood. Which is giving me no dash lights running lights parking lights or taillights. Initially the fuse would last for a few minutes and then burn out. I should also add that the trailer wiring harness doesn't work either and the driver side headlight will work sporadically.
I just bought my first Ford its an 1996 f250 powerstroke, and I am having issues with it. Every time I push in the brake both blinkers come on and tail lights and upper parking lights on cab, and when I turn on a blinker everything flashes.
View 8 RepliesI have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesI have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 RepliesMy car is a 1992 Buick Century with a 3.3 liter V6. My tail lights, parking lights and dashboard lights are out. I checked the fuse in the fuse panel and it's good. The light switch is good, I confirmed it by inserting a voltmeter in the empty fuse socket and turning the switch on and off. The wiring diagrams in my manual are not useful. The diagrams don't include the lighting circuits. Is there another hidden fuse someplace? Could it be a bad relay? If so, where the lamp relays are located?
View 4 RepliesI have a 1990 F-350 7.3 lariat crew cab. The tail lights fail to work but all the turn signal and brake lights work. I changed the light switch located to the left of the steering wheel but that didn't solve the problem. all the fuses under the dash appear to be ok to. Is there another fuse for just the tail lights.
View 6 RepliesFirst off my driver side brake light with stop working. I took it apart to try and find the short. In the process I shorted out all my running lights tail lights and brake lights and turn signals I think also. While I was looking for the short, turn signal wire from my tail light touched the frame and grounded out and that's when all the lights died . My tail lights are some cheap trailer lights without reverse lights. I pulled headlight switch from another Ford truck I have. On the harness connector that connects to the switch which wires should read what when I test with a voltmeter?I checked the fuses in the power distribution box under the hood and they were good. Truck has a flat bed so I don't know if that matters with the wiring, I suspect it's different then a normal bed truck. Wiring on the bed is old, maybe from 94. I am unexperienced with electrical.
View 3 RepliesLooking for a schematic on this truck,standard cab diesel. I have a dead short on exterior lamp fuse. I have no tail lights, running lights, door ajar light is also on.
View 4 RepliesThe front running lights come on immediately, but the tail and side running lights take their time coming on (usually 10 to 20 seconds later. 95 Ford E-350. Is their a relay that could cause this issue?
View 1 RepliesI have a 1997 F150. I installed a trailer towing kit round 7 pin. I followed the instruction and replaced three different fuses after installation. The passenger side turn signal will not work. I replaced the bulb. The brake light works and the bulb is on when the lights are on it just will not blink. When the turnsignal is on it clicks very quickly.
View 4 RepliesJust bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesI am beginning to think that I need a whole forum dedicated to my trucks wiring issues ... I finally got my reverse lights to work but my newest issue Is that while driving tonight i lost power to my parking lights, my instrument cluster lights, and my heat control lights... everything still works inside (gauges all act properly but they won't light up) and i still have turn signals and brake lights, and headlights. I really don't know where to start with this one. I don't have an owners manual so i can't figure out what fuses to check or what relays to look at. It is a 2007 f350 diesel....
View 9 RepliesI just bought a 99 Explorer v8 2wd to replace my aging aerostar and to tow my boat. I already knew it had this problem and a destroyed rear diff when I bought it, I figured this would be the easiest problem with just a new switch. I was wrong.
pulled the fuze
pulled the headlight switch
pulled the relays at: power dist. box, keyless entery/alarm?, the box under the dash
disconnected the harness from the GEM behind the dash and from the keyless entery/alarm
Lights only go out when I pull the park lamp relay. I know what you may be thinking. But no. Its still not gonna be that easy. The relay is not bad or being activated. Its just acting as a jumper from pin 4 to 3. So out comes the test light.
At the park lamp relay (without the relay in)on the relay module I get power at 1, 5, and 4. When I ground 2 with the test light, the headlight relay kickes on. Which seems normal to me by my assumption of how the system works. Which is that these relays are only for the RAP module to flash the lights by grounding the 2 pin. Anyway... I think I've narrowed it down.
According to the wiring diagrams, the 4 pin should only get power from the headlight switch and the GEM from a white/black stripe wire. With the relay in (only to jump the power)I have unplugged both the headlight switch and GEM, and the lights stay on and there is power at 4. I figured the white/black wire may have a short to 12v and I would just bypass it. Then today I can disconnect the battery, then reconnect it and the lights will stay off. Keep in mind all other relays are out and everything is unplugged. If I plug the headlight switch back in, cycle the switch, the lights will go on and off correctly, but will eventually stay on. Even after removing the head light switch.
Does the white/black wire go to anything other than the switch, GEM, or relay. It doesn't say so in the diagram but I can't figure out why its getting power intermittently. Still thinking it could be a short I did a wiggle test on the dash harness to try to get them to come on if off or off if on. Nothing.
2005 Super Duty 350. Getting ready to get my truck DOT-ed and I noticed the front amber side marker and parking lamps are not working (both in the headlight assembly). There is a fuse called "exterior lamps" that I believe these are on, the fuse is fine and all the rest of the exterior lamps on the truck work fine (all other markers, clearance lights and I.D. lamps on that same all inclusive circuit). Is there a special relay or something else I'm missing for these four front bulbs?
View 1 RepliesThe truck is parked in the drive. I noticed when the truck had been parked in the drive I noticed that the tail lights came on and then about 20 seconds later turned off. I checked that the ignition was off, doors were completely closed, etc. It has happened several times. I'm worried the there is an electrical problem that might drain the battery.
View 10 RepliesI have an early 99 F250. The a/c compressor stopped working. Have checked pressures, switches, freon etc. Found the switch in the dash is not getting power to send to the compressor. Where the feed for this switch is? I have checked all fuses, all good. The manual does not show a relay as being an a/c relay, so I am stumped without taking it somewhere now but I would like to avoid that.
View 7 RepliesTurn signals quit working on my 2006 E-150. Swapped out the relay under the dash and it did nothing. Also noticed the brake lights aren't working. The headlights and taillight a are working. I pulled the fuses under dash for the lights and they tested ok. I did notice the flasher relay was making clicking sounds intermittently even when not touching anything.
View 3 RepliesWe have a 1999 F-350 V10 super duty. The alt was over charging and the gauges stopped working. Replacing the alt, the guages still don't work, and the new thing is the charge light and selt belt light comes on. The fuses 29 (5amp)and 30(30Amp) which are supposed to be key on hot only are hot at the same time. With these on, it causes a drain killing the battery. Also if the truck is started, the lights go out, but when you try to turn the vehicle off, it stays running, one with the battery disconnected. The only way to shut it down is pull the fuse box power fuse, 50(amp)Some one had been in the dash before we got this vehicle and busted, burned out or removed the check engine light. I can read codes and their vehicle runs fair and does operate. Could this be a dash board? Also this problem appears when the truck is sitting, and the key removed nothing on. No fuses are blown either.
View 3 RepliesSo I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesTruck is in signature. All of a sudden my oem fogs don't work. I took a volt meter to the connection where the bulb plugs in and no juice. Checked the fuse and its good.I get 12 volts or so at fuse for fogs.. The fog light illuminator lights at the switch when I pull the switch. Is there a relay somewhere under the hood. All the relays in the fuse box checked out good and none of them in my truck guide were labeled for the fogs anyways. Looked for 3 hours and cant find a thing. If all else fails how do I cut the wires at the fog lights and run wire to cab with toggle switch? I know I need a relay right? I am not familiar with hooking up relays..
View 14 Replies