GTI 337/20th Anniversary :: Misfire With Engine Code
Feb 11, 2013
So i have a 2004.5 gli 6spd that had two of the coils go bad and had a serious misfire with engine code and all car didnt want to even move. So i got this fixed made it about a mile down the road and it had a cylinder 3 misfire took it back had third coil replaced and all new plugs put it. Got the car back it ran fine until i hit about 4000 rpm under heavy boost it misfires but no flashing cel like before and the car still runs but cold start warmed up it misfires under boost
View 20 Replies
Advertisement
So I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 Replies
Driving the other night I ran drove over a pot hole going about forty pulled up to the stop light and my car starts to make funny noises, barley got the car moving again but managed to get home. I hooked my computer up to it and it says misfire at cylinder 2 and 4.
View 14 Replies
I am having this failure in my engine that is making me crazy while I am driving. Yesterday i took my car to a shop to see what was it. my MAF was gone ( I replaced it ) and the failure still going on. The mechanic connected his computer in my car and we went for a ride. HE told me cylinder 1 misfire.
This is what i did.
-change spark-plugs position (failure still)
-change coilpack (failure still)
What can i do ?
-clean injectors
-check for any carbon in valves
View 4 Replies
What is the factory AWP 20th AE boost pressure?
View 6 Replies
whats the engine code for the 04.5 gli 1.8t???
View 5 Replies
Check engine light just came on. I scanned the car and the code PO704 came up.
"Clutch switch input circuit malfunction."
If I replace my clutch switch, will this solve the problem? I got the part number #1jo 927 189f i just want to make sure its that switch that's bad.
View 5 Replies
I drive an 05 Gli n my car has been shutting off on me took it for a diagnostic n the code po322 came up engine speed sensor. So my question is. Is their a DIY on replacing the sensor I'm picking it up tomorrow. To be honest I don't even know where the sensor is located...
View 8 Replies
So i just got back into town after not driving her for about a week, started her up(barely), and saw engine light. While on the engine putters and sounds bad. The exhaust smells like gas. I have done no Mods except for APR stage one and a K & N air filter. Is it misfiring? Is my software bad?
View 14 Replies
I have a 2004 Jetta gli 1.8turbo my car has 97,000 miles and the last oil change i did was with 0w-40 oil, can this cause my check engline light to come on and 2 cylinder misfires? should i change oil to 5w- or 10w- asap?
View 2 Replies
I changed my sparkplugs and coil packs last month. Was getting CEL light but it would go away after a while. I figured out that I had gapped my spark plugs way to small (almost touching) so I took them out two nights ago and regapped/ reseated them.
My car was running fine yesterday, but today when I started my car up, the engine was shaking a lot for about 10 seconds and the CEL was blinking. After 10 seconds the shaking and CEL went away...
It drove fine. I'm just wondering what could be throwing these CEL's and causing the shaking? Plugs are gapped to 0.32
Also, I had my timing belt and water pump replaced almost two weeks ago now. Any chance that could be lending to the problem?
My guess is that one or more cylinders are screwy. I'd rather not bring it into the vw mechanic since I'm tight on cash.
View 6 Replies
Ive been having two issues with my GLI lately, last week while driving on the parkway my car just randomly lost acceleration, no lights came on but the gas peddle was unresponsive. I was able to restart it while coasting and thought nothing of it. Then it kept doing it. It was raining that night but ive never had an issue before. Other times it dies it is sunny out. The second issue is sometimes when I hit over 10lbs of boost the car will start to misfire and run like crap. No CEL's come on the dash but if we scan it with VAGCOM it says theres misfires happening, obviously. Already did a smoke test and there are no vacuum leaks.
View 19 Replies
I have Unitronics Stage 2, and a 3" downpipe... I keep getting a CEL P0420. I know its about the second o2 sensor, but I don't understand why I am getting the CEL with my chip? Could it be possible that when I put the downpipe back in i reversed the 2 sensors? Or are they the same...
View 5 Replies
Ever since ive owned my 337 its always been a pain to keep my cel off but i got a pocket scanner and found that the code is coming up for a bad ECM !!! i called around and the cheapest i found was 1200.
View 8 Replies
I have an 04 GLI and keeps throwing a code for the 02 sensor, and after putting the car on the lift, and disconnecting the 02 sensor harness, a fine oil leaks out at the end of the connector and smells and looks like power steering fluid.
View 9 Replies
Car is throwing Converter below threshold code. I figured i would put in MagnaFlow High-Flow cat from my work but didnt know if that would work. The position of the stock 02 sensor is what baffles me.
It seems to me the factory design has the 02 sensor in between 2 chambers. Could I just install this Magnaflow cat and put the 02 sensor after the cat? Can get rid of this code after installing high-flow cat?
View 3 Replies
I got a 04 mk4 gli 1.8t and I got a po171 lean code and I know it could be a vacuum leak the maf sensor and other things. But when I clear the code it takes a couple days for it to come back on. But when I do clear it and start the car for the first time the car idles read bad almost sounds like miss fire. The when I pull out it hesitates just for a little than runs fine. Could this be a bad or dirty maf sensor? Like I said it takes a while for the cel to come back on.
View 1 Replies
I have a 2002 GTI 337. I'm getting a P0601 code with the CEL light on.That code says "internal control module memory check sum error".
View 7 Replies
So I recently (within the last month) replaced my DV for a Forge 007 and my stock air box for an EVOMS v-flow. My cel came on after the DV switch and was throwing the P0420 code at me. Then I swapped the intake and it has been good but I felt like I was running a bit rich and pulled my codes and it now has P0030 in addition to P0420. Why this is? I have 88K miles. Spoke to a mechanic and he says he thinks it is my cat dying. I'm a bit confused since I have a turbo back exhaust.
View 6 Replies
I was parking today and when i looked up my CEL was on. So I got the code pulled and it turns out I'm running lean with a base one. I think it was? the mechanic told me it was my o2 sensor but I'm not sure which one it may be whether it be before or after the cat?
View 5 Replies
I just changed both of the o2 sensors on my 337 like i was told and my car ran for about 80 miles until the engine light went back on again I brought it back in to get it scanned again and i got a P1174 code. What it is and some solutions.
View 7 Replies
