I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 Replies2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesAlright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 RepliesNew to the VW world but I am not out of my element for I am a Porsche guy. So I feel right at home. Last night I picked up a 2001 wolfy Jetta with a 1.8t on the cheap with a misfire on cylinder 4.
I have verified I have no spark on 4. I have confirmed the issue is not the spark plug, coil pack by swap and see method. My coil pack and plug work fine on another cylinder. I reset my cels and here are the new ones that pop up:
a 121 - gas pedal position sensor- doubt this would give me a no spark
a 304- Misfire on 4, (duh, like I needed to hear that)
a 030- bank one 02 -Doubt this would also give me a no spark condition)
In my testing:
I have good system voltage on the coil pack
I have good ground ohms
My signal wire is not shorted high or low
When I take V and ohm readings on the coil pack connection, either with the ign on or off they are all in line with the other sensors. So I don't think I have a wire issue.
The PO had the ECU replaced at a local dealer. I looked at the old ECU and it appears it had got wet at one point.
Im wondering if the same thing hasn't happened to the new one. however after they replaced the ECU they gave him the car back still broken. So it never ran even with the new ECU.
1 Where is the ECU?
2 What tells the ECU to fire the coil packs at the right time?
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 Replies2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 RepliesI bought a 2001 golf gls 1.8T (AWW) about a month ago and it was running pretty bad, was throwing some codes, cylinder 1 misfire and some o2 sensor codes, I replaced the coil packs and spark plugs and then cleaned the MAF. It was still running bad ,rough idle and power loss. I figured it had to be some kind of vacuum leak, I replaced the PCV valve, cleaned the intercooler and put on a silicon TIP. Still had some rough idle and power loss, checked for vacuum leaks, using the good ole starter fluid method and found my intake manifold was leaking so I replaced that gasket. STILL rough idle and power loss, now I'm pulling codes for o2 sensor and a misfire in cylinder 3. My question is, should I replace my pre-cat o2 sensor or replace my MAF sensor? Or are there other things that should also be checked/replace.
View 5 RepliesHave '01 SE. yesterday I got a misfire in cylinder 4 (code P0304) the service light blinked on and off 3 to 4 times than stayed solid. changed plugs and boots about 1 to 2 months ago, didn't change coils and they r not in the best shape but didn't have money to replace at time. So I replaced the coil for #4 and it still runs rough with code, plug has some ware but looks fine.
View 1 RepliesI just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 RepliesI have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
I have a 2001 Honda CRV with about 140,000 miles. It is an upstate NY car, so has seen its share of salt and rough winter driving, has a little bit of rust.
I recently brought it in for repairs because it was overheating. It was over the holiday weekend and I had a job interview to get to so I brought it a chain, which was the only open mechanic I could find. They told me there was a coolant leak and replaced the radiator.
The next day, the check engine came on. Cylinder misfire code. I took it back to them and they wouldn't give me a straight answer on what was going on but insist they told me that would happen and it needed more repairs which I had apparently refused. They told me it's probably the spark plugs/wires are old but maybe there's more damage, but basically that they didn't want to deal with it.
So I brought the car to my regular guy. He says, yeah it needs a tune-up. So he replaces the spark plugs and wires etc and gives it back. I drove it for a day and the light came back on. So I brought it back to him again and he refused to do anything. Wouldn't give me some possible causes or explanations, just says come pick it up. Didn't say stop driving it, take it to a dealer, he just reset the check engine light and said its probably fine.
The next time I drove the car, while it was warming up the check engine light was flashing. By the time the engine was warm the light had stopped flashing and was on.
I know I can fix this problem, but my question is which cylinder is #4? I don't see it marked on the engine. The counter guys at both my local parts supply stores (whose initials are A and O) can't even look it up for me. If #4 is on the front of the engine, then it's an easy fix. If it's on the backside, then the intake manifold has to come off to get to the plugs and coil packs. It's a bit more labor. I can do it, but I'd rather not have to.
View 1 RepliesGetting misfires on cylinder 1 and 5 in my 2001 Jetta GLX. Replaced coil pack. Installed a different/used cam position sensor.
Swapped injector 1 and 5 with 2 and 6. Cleaned MAF and throttle body and did adaptation. Checked resistance of plug wires and swapped plug positions.
[URL] ....
View 6 RepliesI have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 RepliesAlright Ive had a misfire on cylinder 1 for far too long. I've replaced all ignition coils and plugs with oem parts. Also replaced fuel pump and filter with oem. As well as 2 injectors. Before I would misfire under load, now I misfire at idle..wiring looks good and not cracked from what I can see. Only codes I reciece are random multiple misfire, misfire cylinder 1. And diverter valve mis function because of my BOV. So what do I do now vortex?
View 1 Replies