Have a question when I shift slow from 2nd to 3rd my o2j tranny doesn't grind but when I shift fast from 2nd to 3rd it grinds it happens starting at 3000 Rpms thru 6000 Rpms. It also doesn't happen when I shift from 4th to 3rd. Have performed a tranny fluid change. Along with replacing the clutch at 1500 miles ago. The engine is AWP.
View 4 RepliesGot a 2001 Jetta 2L automatic 200k miles with gremlins. possibly multiple unrelated problems. First problem that presented is that the transmission will occasionally not shift into 4th gear. I discovered that if I stop the engine, then restart it, it will again return to normal operation, hence the thought that it is electrical. After a year or so of this, second problem pops up: the engine will die while the car is driving, or some times idling at a light. I've also noticed that the interior lights flicker somewhat in intensity when on and the engine is operating, so there could definitely be a grounding issue somewhere. I have heard that the ECU/ECM connectors could become corroded, but haven't yet dug into it to look. Any guesses as to where to begin?
View 2 RepliesSo after my 500 mile break in I decide to see what my new set up is made of. Had the kinetics stage 3 and the south bend stage 3 clutch installed. Did my first launch...everything went great. Got just a little bit of spin and the car took off like a scud missile. Right as Im going to shift into second my Rpms go down fast. No weird noises no metallic sounds nothing. No fluid under the car. Only a slight clutch smell nothing crazy. Car wouldn't go into gear. Shut the car off and it goes into gear.
View 20 RepliesI have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 RepliesI just traded my MKIV GTI yesterday for an R32. Super happy.
But I have a question, Should I put in new tranny fluid? cause when I try to go fast and go from 1st to 2nd it gets blocked, but if I'm going slow and slowly feather the clutch it goes into the second fine.
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
when i shift from 1st gear to 2nd gear, above 2500 rpms i get a really bad grinding, i am just under 50,000 miles so it is going to the dealership to get fix. It also kicks me out of second gear some time.
View 24 RepliesSo i was trying to adjust my freinds shift linkage on his o2j and i got a little ahead of myself and forgot to put the shift tower in the home position before making the adjustment. after i realized you can't shift into second ( either that or 2nd and 4th are extremely close together now and feel like the same gear ). I try to get it in home position even with the cables off ( did this for experimentation) and still wouldn't go into home position...meh. still have all the other gears including reverse .
View 4 RepliesMy 03 Jetta is having transmission trouble. It will shift from 1st to 2nd but wont shift to 3rd. It is an automatic 2.0.
View 10 RepliesBackground facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
I have been experiencing some grinding when I go from 2nd to 3rd, so the first thing that i did was to replace my trans oil but it did nothing so I went to my mechanic and he said that I need to replace the gear synchronizer. What is the part number and the real name, what i need is what is in the picture below.
My car is a mk4 1.8T with 5 gears....
OK so my 02m goes into to all gears but when I try to take off it makes a grinding noise and kinda feels like it wants to start hoping. The car set for about 2 weeks and didn't have a problem with this at all. I can also shift the car into gear when started and not push the clutch in.
Car has a fx400 clutch with billet flywheelsl
Started noticing an issue with my trans awhile ago, the other day it stopped shifting out of first when cold. It's a 1.8T auto 5 speed tiptronic, it's the Jatco 09A. I know the shifting problem is the solenoids and it doesn't look that hard to swap them out. The trans shop said it looks like there is slippage on gears 2-4 and the fluid is toast. Looking at replacing or rebuilding, shop said 4-5 grand, how easy would it be to swap in a used trans? And what kind of issues would I be looking at?
View 1 RepliesI replaced the old auto trans that was slipping in my 2000 golf with a same year auto trans from a beetle. The beetle had 115k miles and the PO toasted the 1.8t. I replaced the TCM also and when I finished the install I took it out for a drive this afternoon and when I shift it into drive it starts out in 3rd. It will manually shift through the gears but it will not shift from 3rd to 4th. Could I have left something unhooked? Is this a solenoid issue?
View 10 Replies2200 Miles... It will not shift into 2nd gear in automatic and the rpms race up to 4000 when going about 20 mph. The only way to get it to work again is turning car off and on again. It has only happened twice.
View 7 RepliesMy buddies Jetta won't shift into high gear. I am going to take a look at it this saturday to find more out.
View 4 RepliesWhen I'm driving, the Jetta will sometimes not shift from 3rd to 4th gear, so I just turn of the car a start it and it seems to work, but eventually does it again. Once it is in 3rd gear it does not downshift and stays in 3rd even when stopped. The trouble code is P0785 which is the shift/timing solenoid. Not sure if I need to get a new part or which solenoid to get. Also I cannot figure out where this solenoid is actually located or what it looks like.
View 1 RepliesOkay so I bought this car and a week later tranny wouldn't shift out of first when I would slow down or at least it would take a min. I would hit 4or 5 grand then it would jolt me back. It wouldn't do it every time though. I bought it to go to college drove it the 900 miles on the highway and had no problems except right before I left town but then fine. All I did was change the tranny fluid before I left which I can confidently say I don't think has been changed before that. stunk bad bud no metal.
Alright now I'll go jump in the car to go to class and it will not leave first. If I put it in the manual mode it thinks it's in third but clearly if in doing 15 mph at 4000 rpm that's not the case. It doesn't do it every time. Kinda hit or miss. After driving for a min it usually shifts. Sometimes I make it the two miles without it shifting though. Also sometimes It will shift but once I slow down it won't shift out of first again.
I have seen a code for torque management since I bought the car. The check engine light is on now but I haven't seen the torque code since I change the MassES. that's not to say it's not still there. I used a different handheld computer for the check engine light the last time I did it and I could have missed it because I was unfamiliar with it. I have put a mass airflow sensor, battery, alternator, and changed the tranny fluid since I have owned the car. drained 3L of tranny fluid and put 3L back in. Oh and the last time I checked the light it said lean in bank 1 but I was assuming that was an unrelated issue.
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
Just bought this car yesterday. test drive went fine with no issues. Started driving it home and the check engine light came on ( no big deal i thought car runs great). I go to advance auto and their scanner won't hook up to it. So i start looking at the fuses and everything was good except it was missing the the number 7 fuse ( reverse lights/speedometer sensor), so i replaced the fuse. i get home and i decide to take it down the road one more time and it all went down hill quick. EPC light came on, the car wont shift out of first gear (automatic). so i let it sit over night with the number 7 fuse out and the battery disconnected. CEL never disappeared this morning and its do the same thing. It looks like the MAF was just replaced and the brake light switch looks like the newer green version. Im going to replace the brake light switch this afternoon and i already cleaned the MAF. Another thing that i noticed that is very strange is now the Foot symbol by the shifter has gone out. The one on the dash still is working properly but the one at the shifter does not light up at all now.
View 1 RepliesI have the mods listed below in my signature. When I shift gear and have almost completely released the clutch to move up into the next gear I get a clicking noise and feel from my transmission I think or maybe differential. This is with traction control off and is only noticeable at lower rpms like a low rpm shift from 1st into second.
View 7 Replies