Golf IV / Jetta IV :: When Shifting Into Third Gear Sometimes Shifter Does Not Move All The Way Forward
Sep 11, 2014
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
View 5 Replies
Advertisement
2000 VR6 automatic. Yesterday my car was stuck in park couldn't move the shifter . Figured it was the brake sensor switch when the brake is engaged food pedal lights do not go out, I replaced it this morning but still won't work I've been driving it around in limp mode?
View 4 Replies
I've got a 1.8T 2004 automatic and the problem I'm having is the shifter is harder to move since the weather's been colder. It shifts very well and is responsive, it's just that I have to pull it harder to select P, R, N and D. D is especially hard (no pun intended you sick minds! ) to select, the shifter kind of stays in neutral but shifts after a bit. Is there anything I can do to fix this?
Side question: is the rear defrost supposed to turn off after a certain period of time? My 2002 golf does it but the jetta doesn't.
View 5 Replies
The issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 Replies
I have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
View 18 Replies
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
View 10 Replies
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 Replies
My03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.
View 7 Replies
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
View 5 Replies
I'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
View 3 Replies
I have a 2000 Golf GLS which I tried to replace the shifter solenoids on and since I replaced them it shifts very very incorrectly it almost feels as if it starts in 4th gear and works its way to 1st.
View 2 Replies
So today I was driving my car and everything was fine. I get to a freeway off ramp. I put it in first and it goes like normal I shift from first to second and then into third when i shifted into third, I hear a grind sound like I miss shifted or something. I continue on and when I get to a red light I go to take off in first and nothing...The car wont move!! I have the clutch all the way out and its in gear and nothing... I can have the car running and the clutch out and i can shift it in any gear and nothing happens. I have a spec stage one and an 8lbs smf in the car and before i could hear clutch chatter and now when i have the clutch out I don't hear anything? What is causing this?
View 3 Replies
I have a mk4 jetta that I bought a couple of months ago it is a 1.8T 5speed and the last 2 days of driving it 3rd and 4th gear maintain in place like they should but when I try to give it gas the rpms skyrocket and the car does not move, it is like as if it is in neutral while still in gear....What the problem is?
View 3 Replies
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
View 1 Replies
I need removing the console on a 2005 Malibu Max. The switch on the shifter will not move the transmission down to 2nd or 1st gear. There was a post by "shadow5599" on 05-05-2009 stating that this problem was caused by a broken wire in the harness under the console leading to the shifter +/- switch. He said it was easy to fix but the console needed to be removed. Later on the same day he posted that he had just posted the instructions on how to remove it. I'm a first time user on this site and I haven't been able to locate those instructions.
View 1 Replies
Here is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
View 3 Replies
Got in to go to work this am, and the gear shifter was difficult to move. What to check?
I drove 70 miles to work and didn't seem like any issues with the transmission shifting.
Got in to go to lunch and it seems even more difficult to move...
Shifting back and forth in the selector seems to loosen things up a little.
A friend move the selector while I looked at the linkage and the bracket that support the cable is flexing while shifting between gears....More likely a transmission issue or something with the linkage?
View 24 Replies
My 2000 SD 7.3 has developed a quirk. For some reason the trans has decided to shift late in all gears. This only happens once, then resumes shifting normally. However the OD indicator on the shifter blinks from that point forward. Once the engine is shut down and restarted. The sequence starts again. Late shift, through the gears, once, then shifts normally with light blinking. Fluids are up and clean.
View 4 Replies
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
View 2 Replies
This morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
View 9 Replies
My 2004 expedition wont go into any gear the shifter will not move I changed the stop light brake switch and a 30 amp buss fuse I found blown and also the check engine light is on now too this was after I parked it I also changed a 30 amp buss fuse I found blown out but it still don't work the only way I can get it into gear is to push the little button under steering wheel...
View 2 Replies
