Honda Accord 2004 EX V6 150,000 Miles. The car is paid off, I'm the original owner and it has no problems, apart from it seems like the clutch is beginning to wear down. Some times in drive when I step on the gas it spins up just a little and jerks forward. Is is worth getting the clutch repaired?
View 10 RepliesWe took our car in for a regular oil change and to get the 60K belt work done. While in the car they discovered that the transmission was slipping and that we were missing one of the motor mounts. They did the belt work and the oil change and then put some fluid in our car hoping that would buy us some time with our transmission. To save us time and money they said we could wait a little while on the motor mount. When I drove it home the whole car shifted and shook whenever we would come to a stop and then it would shake while idling. I called our mechanic back and they said to bring it in and that fixing the rear motor mount should take care of the problem. While back at the mechanic for the motor mount they discovered that the transmission additive had not worked and we needed a new one.
We bought a rebuilt one and now we are still left with a car that shakes when we are idling. We have had the car in two or three times after the transmission was put in for them to try and fix the issue. They have done everything short of removing the engine without any luck. Just to be sure they covered every possible angle, they just gave us new spark plugs, ignition wires, distributor rotor, distributor cap and PCV valve, but it didn't seem to do anything. The car shakes the most while idling in Drive, somewhat less in Park, somewhat less than that in Neutral and not at all in Reverse. The shaking gets even stronger if the A/C or defroster is turned on. It seems to be even worse when stopped on a downward slope. It has been several months of this and the shaking is incredibly annoying. Is there anything else our mechanic could look into?
We have a '94 Honda accord that the automatic transmission started "slipping" in a week ago. It has 240K and runs good otherwise. It was sliping after it warms and seemed to slip mainly while shifting from 2nd to 3rd and 3rd to 4th while accelerating quickly. If you take it real easy on the gas it does not seem to slip much (the engine revs and the car does not seem to be accelerating, so I assume that means it's slipping - maybe not?).
I don't believe the auto trans fluid had been changed in over 100K+. The car sat for about 2 years and then I changed oil, replaced tires & battery and started using it with no probs until this (I've been using it for about a month now).
Today I changed the auto trans fluid (very dark/dirty but no real burn smell - and just a little metallic "shavings" on the magnetic drain plug), and drove the car fairly hard and heated everything up real good and it hardly slips at all now.
My questions are - with the fluid change making such a drastic improvement (at least for now), should I repeat the process and change it again? Should I try an aftermarket "miracle" additive to claims to prevent slipping? What about trying the Honda brand fluid vs. the "Autostore" brand Dexron VI that is recommended for Hondas requiring Dexron II (apparently they don't make D-II anymore)? Could it be something else - sensor, linkage, etc. (seems doubtful with the improvement with the fluid change?)?
I have a 2000 Honda Accord EX v6 and I have been taking it the dealer for regular maintenance and Oil Change but today I noticed my Car would not start
I can hear the engine start , but when I put the Gear (automatic ) in either reverse or D4 the engine will stop.
Then I waited for some time and restarted it and It was OK.
I have a 2000 Accord with about 65000 miles on it, 5 speed manual. The clutch is getting flaky. One time recently, it went to the floor and stayed there until I pulled the pedal back out. Then it worked fine for many days. Dealer could not get the problem to repeat; no leaks found. But now sometimes it is hard to get the car in gear (especially reverse), or the clutch feels spongy, but not in a consistent way.
View 2 RepliesI own a Honda Accrod 2005 V6.
I don't know much about cars, but for the past year my clutch gradually started to just stick to the floor. I'm now at 80,000 miles, the clutch doesn't slip, and it for the most part drives fine with exception to this sticking. Sometimes when this happens, the stick shift stays in gear and I can't get the stick out of gear until the clutch has been lifted up and pushed back in. It is def getting worse. I have brought it to several mechanics.
I have been told by Honda that I need to replace the clutch set (clutch disc, pressure plate, and throw out bearing) and the clutch master and slave cylinder.After another mechanics look over, they also did confirm the same as honda but stated to get a new cut flywheel.
But after several other mechanics look-overs, they told me that the clutch is fine, so they recommended me to get the master and slave cylinders replaced.
So, trying to save money a mechanic told me to take one step at a time and see how it goes. He said he will bleed the slave and master cylinders and see if it is just an air pocket. That didn't work, so I trusted him and he replaced the master cylinder, but the problem still exists. He said the next thing to do is maybe to do a new slave cylinder. I'm now contemplating.
Another mechanic took a look after the work was done and said there is no leaking.
I just had the front seals replaced in my 93 accord standard shift wagon. After about 4 days the clutch started feeling "soft" and now it's almost down to the floor in order to engage it. I wonder if this has anything to do with the seal replacement?
View 14 RepliesA couple of years ago I went through the salt water with my 2003 Honda Accord which is a manual transmission. It only has 106,000 miles and expects it to go much further. The clutch works great but when engaged is really loud. I have had it checked by 2 different auto repair places. Nothing is wrong they say. It has been cleaned and greased.
View 19 RepliesWe have a 2000 Honda Accord, standard shift, with 105,000 miles on it. The clutch has been sticking at the floor on random occasions (especially on hot days). Our mechanic (Honda Dealer) has not been able to correct the problem. Last summer he changed the clutch fluid and said that looked like the problem as it was vey dark. It corrected the problem for a few months but now it is happening again in the cold weather. It can happen at any time you depress the clutch, even while shifting when moving. Of course, then it is very difficult to get the car in gear. Our only solution is to manually pick up the clutch with hand or foot and this is dangerous in traffic.
View 4 RepliesHad my original clutch replaced by mechanic. Had 200K on it. Car clutch petal vibrates badly when bringing clutch pedal out after shifting. Mechanic states it has to do with motor mounts that were affected when changing clutch or the clutch takes time to seal and stop vibrating in the next 500 miles. I have warranty for 12 months and 12,000 miles. Which I had no problem of vibration before having clutch replaced? What is the problem and how to proceed.
View 3 RepliesI have a 97 Honda Accord LX stick shift that's giving me some trouble. I bought it at 146k miles and now it has 151k miles.
-- Here is the symptom --I feel that I have to lift the clutch pedal higher to fully engage the clutch after driving for 20 mins. The problem showed up several times and one time the clutch was somewhat slipping and I had to park it somewhere and got towed. After sitting there for several hours or overnight, the problem would gone -- and it could show up again at some time. The strange thing is that I am not always getting this problem. The car could sometimes run over 1 hour without any unusual feeling on the clutch.
I also noticed that when the clutch is not working well, the clutch pedal is stiffer than usual (I never had problem disengaging the clutch though). When I push the pedal to the very bottom on the floor, I can hear some noise and the car even had a tendency to move a little when in 1st gear.
Once I opened the hood and looked at the position of the release fork when the car was cold. After driving about 20 minutes, I looked again and found that the fork moved a little bit away from the slave cylinder as if someone was pushing the clutch pedal gently! I think that's why the point at which the clutch engages is becoming higher. But I don't know what is the real problem. I replaced the slave cylinder last week but it did not solve the issue. Is the clutch bad again or the cylinder?
Here is the repair history --About a year and a half ago I found the clutch slipping. So I had the clutch replaced and the flywheel resurfaced by a mechanic. It was good for a few months until that problem rose again. Then I went to an auto shop. They told me that the slave cylinder was the real problem and got it replaced. I was good for about a year. Now I am still getting the trouble above.
I have 2013 Honda Accord 6 sp manual with 25k miles on, its clutch was completed gone last week, got new replacement, local Honda customer rep. told me I should watch my driving pattern, should using more break, instead transmission slow down, particular from high speed/high gears. I told them, we have 2008 Civic 5 speed Manual, I taught my two daughters how to drive it, and the car is still running without any problem… And, this is manual transmission car, tell a driver can not using/changing gears slowing down car is a joke… but maybe I am wrong...
Is there a possibility Accord has design problem with inferior clutch materials used on their new 6 speeds manual Accord? Since car has new clutch, should I keep it for a while? Or, sale it immediately? I just can’t not see I am going to come up another 3rd replacement on clutch before the car get into 60K miles.
My car stalled one day like I was in a high gear at too low of a speed when i was in neutral. It now acts as if it is in a high gear all the time when I am in neutral. When I press the clutch it will idle like it is supposed to but when i let off it pushes forward slightly then stalls exactly like it would if i was in 4th or 5th gear. When I shift into 1st 2nd 3rd or reverse it dies as if it is in gear but will not move even slightly, when I shift into 4th or 5th it again dies but it but is acting just as I would expect 4th or 5t to at a complete stop i feel slightly more power in 4th which is expected being a lower gear but I also feel 5th pull just like its supposed to. I cannot get it to come out of the high gear it is in even though i can move the stick into the neutral position. It is difficult to get the shifter into 4th or 5th but it will move into the other positions like it should with the same no power result. My clutch is fairly new and i have tried inspecting my sift linkage wit no obvious problems. (1991 honda accord lx 5 spd, 2.2 sohc)
View 2 RepliesI have changed the clutch master cylinder on my '03 Honda Accord (6 cyl.) six times in the past 12 months. Either the o ring seal blows out or the bolts holding the plate down breaks off. I bleed the clutch of bubbles until the oil runs through also. What am I doing wrong?, I'm about to send this car packing.
View 9 RepliesI just rolled over to 90,000 miles on my 2002 Accord. Its running beautifully, however every so often the car "rumbles" or "shudders" when I'm releasing the clutch after I shift into second gear, or sometimes it'll do it when I'm facing up a hill pulling into first gear letting out the clutch. Its almost as if the clutch rapidly grabs then slips a bunch of times, similar to if it was warped. It doesn't completely slip at all to my knowledge. The car was bought new by my family and has been driven pretty carefully since (although 2 people have learned to drive stick on it, and my dad isn't the most "gentle" driver in the universe). I know that Clutch rebuilding and replacing is a big expensive job and its something I wouldn't even consider doing myself. So, when is it time to really seriously consider dropping down the serious cash to get the clutch rebuilt? To be honest, the shuddering is really annoying (it doesn't happen all the time though) but its something I could live with for a bit.
View 8 RepliesMy clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad...
View 1 RepliesMy clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad... 2007 Honda Accord Manual Transmission
View 8 RepliesI have a stick shift 2003 Ford Focus with close to 95k miles. Last week, the car started bucking at low RPM when it's in gear. It happens in all 5 gears, but less violent in the higher gears. To describe the bucking, imagine you're coming to a stop, and you forgot that you're still in fifth. That's kinda what it's like - as if it's ready to stall, but catches itself.
Since this doesn't happen when I'm in neutral or at higher RPMs, I'm guessing it's nothing to do with spark plugs or timing belts. Since it happens in ALL of the gears, I'm guessing it's not a gear going bad. My deductions leave me with the clutch.
I've had this car for a while, but I hadn't grown up with manual transmissions, so I don't know a ton about them. Also, I know that the clutch is more of an assembly, so I'm wondering what PART of the clutch may be going bad.
BTW, I'm also keeping in mind that the clutch may not be the issue at all, so fire away!
2004 Honda Accord sedan, 4 cylinder, approx, 95,000 miles, uses oil rapidly at highway speeds (one quart in 90 minutes), in town driving will not use any oil over 3 to 4 months of monitoring. What the problem is and how to fix it?
View 4 RepliesI have a 2004 Honda Accord 4 cyl that just had spark plugs changed and battery posts cleaned but is acting like it doesn't want to start. Today it stalled 2x when I tried to start it and on 3rd attempts turned over. I put some fuel enhancer (from NAPA) in w/ premium gas, but usually don't get premium. I live on dirt road so it might cause problems. Honestly, I don't know a whole lot about cars but love my accord and want to fix it myself, if possible. What I should do or look into fixing?
View 11 RepliesOne morning after parking and turning the car off, I tried to restart and it just made a sad attempt. A few minutes later it started, but still seemed to take too long. I took it to the dealer and they said the Alternator needed to be replaced, so they replaced it with a rebuilt alternator (without asking me if i wanted rebuilt or new). Anyway.. when i picked it up it still seems to start a bit slower than normal, but they said that is typical for hondas. A couple of weeks later, I picked up my car from the airport after it sat there for 2 nights. It started slowly but surely. I stopped at store, and then it would not start at all. Barely made any sound at all. no cranking... So i had to have it jump started by a tow truck service.I took it back to Honda and they said everything check out ok, and cannot find any issue.I am afraid to get stranded again. Do I need to buy a new car? This one only has 70k miles !
View 8 Replies