Hyundai - Sonata :: Cylinder Misfire / Power Loss While Going Up On Steep Hill
Aug 9, 2015
I am not a mechanic by any means, but have picked up a lot of stuff over the years. I drive a 2003 Hyundai Sonata with a 4 cylinder engine. Several days ago while going up a steep hill I lost power and my check engine light came on. This has happened before when my coil went bad so I figured it would be a breeze fixing it. I limped it home and ran the code. Sure enough it came back as cylinder 1 misfire. This vehicle uses 2 coils so I swapped them to try and get the problem to follow, but it did not. I have tried a new spark plug, new wires, and swapped injectors without success. There is still no activity on cylinder 1.
I ran a compression test. I get about 60 PSI on cylinder 1 and between 180-210 on 2-4. This would point to head gasket, so I am told. I do burn about a quart of oil every 500-1000 miles, but I do not seem to have any coolant leaking issues. I have not noticed any smoke from the tailpipe. The spark plugs were generally good looking, except for number 3 which had a hard white substance all over the electrode. There does not appear to be any oil in the coolant or coolant in the oil. This seems strange to me as everything I have read said that one of those would happen.
Is there anything else I should look into or is my engine toast?
View 19 Replies
Advertisement
A few days ago I posted a thread about losing power on a steep hill climb with a cold engine. I replaced the hybrid battery and all seemed well. A few days later, the problem occurred again--bummer. (The car has 120K miles and has spent most of its life in a hot and mountainous environment, and I knew the hybrid battery was failing, so that's not a problem.)
The car starts the climb OK, gains a few hundred feet in elevation, still has some charge left in the hybrid battery, then loses power, surges a couple of times, then comes to stop. The engine continues to run at idle and I get no warning or check engine lights. The "ready" light stays on. This time, the second time it happened, I turned off the car, turned it back on again immediately, and all was well. The remainder of the 1000' climb went fine. As did several other similar climbs on the same drive. Since then I've climbed this hill with a cold engine without a problem, so it's intermittent.
I hesitate to pay Toyota for a code scan since the check engine light did not come on. Should I do this anyway? My local auto parts store will scan for free, but I know that their scanner will not read Toyota-specific codes, just industry standards.
View 9 Replies
I have a 2005 Hyundai Sonata 4cyl. and have a misfire problem with the 1st cylinder. I've had it pressure checked and there isn't a problem with the cylinder, such as a ring or warping problem. I've replaced the wires, both boots, both ignition coils and the plugs twice. I was told I need to replace the ignition coil again but I wonder if there is something that is making the coil go bad. I've also replace the throttle position sensor and both O2 sensors. I had the front catalytic converter replaced because it was bogging down and very slow. It still runs rough and the check engine light is on. I was told also that I need to replace the engine speed sensor. I bought the car in Oct. of 2004 and only has 68000 miles on it.
View 2 Replies
I have a 97' hyundai tiburon, I have multiple misfires that are p301 302 304 and rich airflow. I have changed the coil pack, spark plugs and wires, and the MAF sensor. Basically my car doesn't accelerate fast or go over 40(max), it putters when i try to accelerate.
View 1 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
I had plugs and wires changed to try clear code. Car seemed to do some better but while trying to go up a steep hill car started stuttering and jerking. Power went out of car and check engine light started blinking fast. After let the car sit for bout 45mins car started running fine again and light stopped flashing but remained on. Code read cylinder2 misfire again.
View 1 Replies
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 Replies
I had plugs and wires changed to try clear code. Car seemed to do some better but while trying to go up a steep hill car started stuttering and jerking. Power went out of car and check engine light started blinking fast.after let the car sit for bout 45mins car started running fine again and light stopped flashing but remained on. Code read cylinder2 misfire again.
View 10 Replies
Having 3 new codes coming up. P0306-misfire on cylinder 6, p0158, p2272. Use my truck as a daily driver for work. Driving along before 80km/h is not to bad but can still feel a little loss of power. If i step down on gas the truck has no power and sounds like maybe cat converter is plugged. If truck is pushed to limit she will make it to her 4000 rpm and will change her gears. So i'm just glad its not tranny.
View 3 Replies
Replaced the spark plugs and wires a couple months ago. Started skipping yesterday throwing the #4 misfire code so I replaced the coil pack, reset the check engine light but it's since came back on and has a rough idle and loss of power. By the way, it's a 97 F150 4.6L 4x4 with 200,000 miles.
View 4 Replies
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
View 2 Replies
Was climbing a steep hill at 35 mph just before truck down shifted to 2nd, I was hearing a pinging sound. Sounded like only I cylinder was doing so. What it could be. I am currently running a 1/4 tank of Fppf fuel injector cleaner. Is this a injector noise. No knocking just a slight pinging.
View 1 Replies
I have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
View 4 Replies
Every time I go up or down a steep hill (usually about 30mph) I can smell something burning when I get out of the car. Going down hill, I figure breaks. Going uphill when I never touch the brakes, not so sure. Also, it's too early to tell but after my 5,000 mile oil change ($56.85 BTW) I seem to getting about 1 mpg better.
View 12 Replies
I recently drove my 2004 Prius up some steep hills in the Smoky mountains. The next morning while driving to work, my dashboard lit up like a Christmas tree, with multiple idiot lights suddenly on simultaneously (none of them informative).
I turned around and drove to the nearest Toyota service center. They informed me that the timing belt was cracked, the HV computer was bad, and the PCV valve as dirty and needed replacing. I think the hills were too much for the car. I will never take the car into the mountains again.
View 16 Replies
I have a 2012 Nissan Versa with a 1.6 Engine/CVT transmission. When going down a steep hill the RPMs rev up to at least 3000 or more...is this normal for a car to do this?
View 3 Replies
My TDI has slow acceleration, just curious if that was common. How do u check turbo. I can still hear it. its now very loud though. Its especially slow when going up a steep hill. anyway to make that faster???
View 24 Replies
I've noticed that my 2012 Passat TDI heats up a bit when going over a steep hill or mountain pass. When driving up steep hills I notice that the temp gauge climbs from the dummy position 190* to about 200*. Once I crest the hill the temp will go down and it won't go up again unless I go up another hill. Is this normal? I had assumed that the temp gauge was a dummy gauge like in most cars so seeing the temp actually climb has me concerned.
View 4 Replies
I have an E-350 with auto trans and 460 engine. I am away from home and hope to make it back where I have tools to do the major work. I drove up a very steep hill and the trans fluid leaked at the steep part, but only when pointed uphill. I did it a 2nd time and it only leaked at the steep part (I was not aware of this the first time or I would not have done it again). Fluid was dripping out pretty good at the bell of trans. No leaks when in drive or R when engine running and level.
I added fluid and tried to back uphill to get van out of this place and it worked fine for a min, but now just rolls downhill. My question is can I just add fluid and get home? What the leak is? How long I can drive it, or if it will leak too much? When I get home (150 miles) I can do any repair needed, Im just trying to get home now.
I know we will be guessing a lot. Van is a 1995 Ford Cube Van, formerly a Ryder moving van. E-350 with the 460 engine, and 3 speed OD trans. I don't know any more detail on the trans. It should be heavy duty given it was a moving van. Van is probably 10-12,000lbs.
View 7 Replies
My 2012 transmission seems to slip a fair amount (much more when it's cold).
When I say slip, I mean, when I give it the gas, it will rev up sometimes, and not move or move very little, while other times it will jerk around like a wild horse. The engine will rev / jump from 2,000 rpm to 4000 back and forth, back and forth. It will do this until it shifts to a higher gear and will stop doing it after 5 - 10 minutes?
On one occasion while going up a steep hill, it starting going backwards while I was giving it the gas. It caught up to itself and started jerking forward until it caught and went forward.
View 14 Replies
On a steep hill, mine rolls back when the transmission is in high range, but it does not roll back when it's in low. On a mild incline, mine does not roll back when the transmission is in high.
VIN: '04 43xxx; latest tranny flash ("520" was the number, I think).
View 18 Replies
