I have a 1995 Infiniti G20. I was driving and everything was fine when my clutch went straight to the floor. It was incredibly arduous to pull back up, now the clutch is very stiff, almost impossible to push down. What could the problem be?
View 3 RepliesI have a 2001 Volkswagen passat glx and last week I jumped in and hit the clutch and it fell straight to the floor with no resistance and i barely touched it.... What this means and if i can fix it myself instead of taking it to the dealership ?
View 4 RepliesI have a 1994 Toyota Pickup DLX 3.0 V6 5spd. I love this truck to death since I inherited it from my grandfather.. however, I have a small problem. Whenever the truck sits for about 3 days without being driven; when I go to drive it the next morning, the clutch will go straight to the floor when I press it. Sometimes it'll even stick. After pumping it about 20 times (it's hydraulic) it'll be fine. It hasn't always done this. The clutch fluid level is fine.
View 4 RepliesSo last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
I've been driving manual 12 years, all my driving life, and been in 10+ manual vehicles during that time, including a 10+ year stint in a 1.8T Passat with a 5-speed.
In all that time, and all those experiences, I've never replaced a clutch, damaged a clutch, or had one problem. In fact, I consider myself a very good operator of the manual transmission.
This is preface to my current situation. 2009 Tiguan (early build) 2.0T 6M, driving at 57mph in 6th gear - downshift to 4th to pass a truck and WHAM. Grinding, confusion, and then the clutch pedal stuck straight to the floor. Glide to a stop on the side of the bayou road.
Totally immobile vehicle. Impossible to shift into gear, or get the pedal off the floor except by pulling. Smell of acrid smoke.
VW dealership says "we're doing a courtesy warranty repair" on the clutch, flywheel and bearings, as if it's my fault. Impossible. This is a mechanical defect if I ever saw one.
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesI've got a 2001 Excursion with the 7.3 and while out driving around on Friday I noticed that my brakes were gone and when I pushed the pedal it went straight to the floor. I pulled over and put in brake fluid (it was empty) and managed to get home. I have discovered that the brake line (it is metal) that runs from the front to the back is rusted out and the brake fluid is just pouring out of it. What is the part called? I spent about a half hour looking for that particular schematic on the ford parts web site but couldn't find any mention of that brake line. Here is a picture. There are 3 metal lines and one is leaking the brake fluid? Can I fix it in my driveway or should I have it towed somewhere?
View 4 RepliesI have a 2003 Ford Escape 3.0l V-6. In June while driving to a job interview, my brakes unexpectedly failed. With absolutely no warning, the pedal went straight to the floor. I replaced the master cylinder...problem solved. 5 months later, driving to the gym, after stopping successfully several times with no mushiness in the pedal, at an intersection, the pedal goes straight to the floor...no stopping power.
I can't remember if the brake light came on last time. This time it did. Both times the fluid in the reservoir was full and looked to be relatively clean. Both times there were no apparent leaks in any of the fuel lines, abs module, at the cylinder, etc. I'm no slouch when it comes to car repair. The master cylinder replacement was done correctly, the lines were bled properly.
I have my own theories but I don't like any of them as my car rolls properly at idle, my brakes have not, nor do they currently make any noise or grinding sounds, and the pedal goes all the way to the floor.
So my clutch has been acting up lately. When it sits for a few hours the clutch engagement point seemed to creep down but over the course of 35 minutes of driving would work its way back up again. Today it was unusually low and wouldn't let me get it into gear. I tried pumping it a few times and realized it wasn't coming back up all the way, I pulled it up and then tried again and it just dropped right to the floor where it now sits. Fortunately I was at work and can hang here until my ride arrives, and will just wait until late tomorrow night to drive it to my shop without stopping...
My guess is I need a new clutch master cylinder. I have plenty of fluid in there although its a bit old so I'll be changing that when I change the cylinder. Could it be the slave cylinder? If so is it a bear to change that? (do I need to drop the trans?)
I have a 2001 jetta with a Vr6 the clutch petal just goes to the floor. No return. What's could be wrong?
View 2 RepliesI have a funky screaming noise coming from my clutch when I press the clutch in down to the floor if I don't press it to the floor it doesn't make noise
and car still drives fine what is this noise. It makes a noise like when you over start the car it's weird. I never heard anything like this before is it a new clutch. I need or new throw out bearing of do I need to breed the clutch?
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
Just got in my car and the clutch went to the floor and stayed there when I stepped on it. What are the steps to diagnose this problem? I'm assuming my slave cylinder went kaput!
View 11 RepliesI picked up my Santa Fe yesterday. 7 seater Premium manual.
However the clutch does not seem to disengage until very close to the floor almost to the extent that I feel the gears crunch and r a little notchy in use because of this ???
Is this a characteristic of the manual gearbox for the new model ???
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
50k Miles on my clutch. Was driving a couple weeks ago on the highway and clutch stuck to the floor. At first I thought it was my Slave cylinder. Got the trans out this weekend to find the mess (below) inside my bell housing. Obviously need a new clutch now and will still replace the slave while I am in there.
Cars setup is around 375ish whp. I know I could spend 1300 bucks and call it a day for a clutch master or south bend but was seeing if there is a cheaper alternative.
Also If I were to buy an OEM clutch or an upgraded one that was not rated for up to 400~whp would it drive and pull the same as a fully upgraded one just not last as long?
6 Speed ...
My clutch pedal went all the way to the floor. The engine was missing first and then that problem happened with the clutch. I had the car towed to my business, I checked it the other day and the pedal was up. The clutch still doesn't engage.
View 6 RepliesI drive a 2004 Kia spectra (base model) w/ 93k
My clutch would start out fine as I start the car, but after pressing on the clutch pedal for about 40-60 times on one trip, it'll start to loose pressure & becomes stickier. And as I press on the clutch pedal more & more, the problem gets progressively worse to the point where I have to manually pull the clutch back up with the tip of my foot.
I also notice that when I drive with the air conditioning, the problem would precipitate earlier & clutch response deteriorates much quicker. But when I let the car rest for a couple of hours or overnight, the clutch response would slowly return, and eventually be normal again.
I own a Honda Accrod 2005 V6.
I don't know much about cars, but for the past year my clutch gradually started to just stick to the floor. I'm now at 80,000 miles, the clutch doesn't slip, and it for the most part drives fine with exception to this sticking. Sometimes when this happens, the stick shift stays in gear and I can't get the stick out of gear until the clutch has been lifted up and pushed back in. It is def getting worse. I have brought it to several mechanics.
I have been told by Honda that I need to replace the clutch set (clutch disc, pressure plate, and throw out bearing) and the clutch master and slave cylinder.After another mechanics look over, they also did confirm the same as honda but stated to get a new cut flywheel.
But after several other mechanics look-overs, they told me that the clutch is fine, so they recommended me to get the master and slave cylinders replaced.
So, trying to save money a mechanic told me to take one step at a time and see how it goes. He said he will bleed the slave and master cylinders and see if it is just an air pocket. That didn't work, so I trusted him and he replaced the master cylinder, but the problem still exists. He said the next thing to do is maybe to do a new slave cylinder. I'm now contemplating.
Another mechanic took a look after the work was done and said there is no leaking.
Came out of a turn, went to grab third, clutch went to the floor and didn't come back. Stopped, pumped pedal for a bit, managed to get into first and milked it home. There's nothing leaking, but fluid level was low. I topped fluid, pumped pedal and bled the block at the tranny, pressure came up and I was able to engage gears. Pulled into garage and same issue, no pressure and clutch won't disengage. Pedal is soft. I'm thinking I managed to get some air in the system. Question is if the slave failed, wouldn't I have a leak at the bell housing?
Do I have to drop the tranny to bleed the slave? Also, my stock clutch on APR stage 1 was doing ok before this issue. There was chatter and/or other noises in the clutch at take off but no real issue with slipping. I'm thinking I'll go ahead and replace the clutch. I'll be dropping the trans on a rack in my friends shop.
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 Replies