Lexus LS 2007+ :: Significant Vibration At Highway Speeds For First Few Miles
May 26, 2015
Owned my 2009 for 6 months now. Ever since purchasing it, car will vibrate significantly at highway speeds when first driving it, then decrease by 90% after a few miles. At first, since I purchased in winter, thought it was cold flat spots on tires. Dealer changed tires 3 times, finally with a new set of Turanza OEM tires. Still does it.
Service manager said he drove new 460's and they all do the same thing for a few miles. I have seen other comments on internet from other owners who report the same phenomenon. Don't think it is the tires since we went through 3 sets and it still does it in the summer. What else could cause a vibration until the car is warmed up?
View 14 Replies
Advertisement
I replaced my tires yesterday with Bridgestone Turanza ER33 (245/45/19).
After replacing the tires, there is is an extreme vibration in the front end of the car when braking at highway speeds (60+ mph). Braking at sub 50mph speeds is completely normal. No lights, no vibration while driving. What could be the reason?
Also while removing the lug nut locks, the locks key broke apart (the black piece came out of the key). After like 45mins of trying, finally we got the locks out. I threw them away.
I searched online for regular lug nuts, but couldn't find any beside ebay. The local dealer says I need to wait for 3 weeks to get them from Japan! Where can I get a set of 4 regular lug nuts online?
I'm now running on 4 lug nuts on each wheel. Could this cause a problem? Could the vibration be caused by not having a 5th lug nut in place?
View 14 Replies
I have an '05 F150 5.4L with 110k miles on it. Bought it used about 2-3 years ago and have had on-going ignition system problems. The current problem is a significant shudder/shake/vibration that occurs when driving 50mph+ (easy to reproduce around 65-70) on the freeway, when starting up a minor, but noticeable incline. This is an incline that doesn't require much additional throttle, and this trouble occurs with cruise control on and off. the truck starts shuddering pretty rough during the incline. However, if I release the accelerator (and go up incline with slightly lower speed) or give lots of gas on accelerator the shudder usually stops. The shudder always clears after the incline when returning to flat road and just cruising.
This occurred on a recent trip a few times and I pulled the following codes (in order):
P0356 (once) : Ignition Coil F (6) Primary/Secondary Circuit Malfunction
P0302 (recurring): misfire on cylinder 2
I have since purchased and replaced the coil on #2. This did not resolve the problem. I have replaced coil on #6 in the last year...
Because I saw a suggestion somewhere on the net around this problem while searching, that this could be related to OD, I tried disabling OD and enabled OD on an incline today to test after replacing COP on #2 and it seemed to resolve the issue to turn OD off. Not sure if related...?
Other observation: Cab of truck often smells of gas just after starting the truck. Mentioned this to the shop, but they didn't find anything obvious.
Short history of codes and work that has been done:
Sometime in early 2011: Ford service dept did this work.
First failure was coil bad on #7. Tech swapped 7 & 8 to verify the problem followed the coil. Then when the problem DID follow the coil, he replaced #8 with new.
05/2011 MacKenzie Ford changed all plugs
12/2011 - swapped out COP on #7.
02/2012 - P0306 - Now, COP #6 is reported as bad.
November/December 2012
P2104 P Throttle Actuator Control (TAC) - Forced Idle
P2112 P TAC Stuck Close
P2111 TAC Stuck Open
I did throttle body clean - removed it and used TB cleaner. replaced...
Late December 2012 - while driving on freeway at speeds 50+, but easily reproduced around 60 after starting up a slight incline. symptom is heavy shudder/shake. Possibly resolved by turning OD off.
P0356 (once) : Ignition Coil F (6) Primary/Secondary Circuit Malfunction
P0302 (recurring) : Misfire on cylinder 2
View 3 Replies
First, details about my truck. 2007 F150 SuperCrew, 2wd, 5.4, 203,xxx miles on it, leveled with Hell Bent Steel 2.5" kit last year, has been aligned professionally since then, tires are good and balanced.
The issue I have is a vibration, kind of the same feeling when driving on a road surface that has had the top level of asphalt removed before it's resurfaced. It's mostly noticable at highway speeds. Its not a violent type vibration, but you can feel it. There is also a sound, similar to tires with a deep off road type tread.
The sound and vibration more noticeable when making lane changes or when wheel turned towards left, at highway speeds, not as much to the right. I've checked front wheel bearings, they are good, zero play, no loose suspension parts, u-joints are good, no leaks anywhere.
Since it makes the noise and vibration a bit more when moving wheel, could it be a power steering pump? The pump is the original.
View 1 Replies
I recently purchased the rims from another member here on Club Lexus.
Ever since installation, I have been experiencing a vibration at highway speeds and while braking. The wheels are correctly balanced.
My technician has told me that I need to buy a hub ring/spacer (not too sure what that is) but nonetheless, a grommet of such that fits between the backside of the rim and the frontside of the hub. I'm not too sure where to begin from there or what to even look for.
View 12 Replies
I have just over 11K miles on my 2011 and now notice steering wheel vibration & slight shake at 70 mph. The passenger can also feel it.
View 14 Replies
I just bought the car a less then a month highway speeds car shakes at 120km/h. I just complained to Toyota dealer ship and they put on brand new front rotors and did alignment at highway speeds the car still is shaking and it pulls to the left can it just be tires alone or back rotors because they didn't replace those.
View 6 Replies
So I have been noticing a shimmy/bouncing at highway speeds (between 60-80mph) for a couple of months. It started right after I had a local indy tire shop swap my sliver stock wheels for the chrome version of the same wheel I picked up locally.
Funny thing is I did my front brakes last Sunday and after putting the tires back on, the ride felt smoother at highway speeds. I figured perhaps the indy shop didn't torque the wheels properly (which I'm sure they didn't as they didn't ask me the torque spec and didn't look it up, and used an impact gun to tighten bolts). I torqued my front wheels to 103lb by hand after doing front brakes.
This Thursday, I did my rear brakes and torqued the rears to 103lb. On the highway the shaking/bouncing is back and dare I say more noticeable.
Could it be that I did something incorrect when installing the rear wheels? The tires are Michelin Pilot Sport A/S 3 with about 15k miles on them. Look to be wearing evenly.
I have an appt. on Monday to have the tires balanced at Discount Tire. I asked about their machine and he said it's a Hunter which I take to me Hunter Road Force balancing machine. Is there anything particular that I should ask or know prior to going in?
View 12 Replies
My car is a 2008 LS460 SWB. I bought it with 69,000 miles on it, has about 75,000 miles now. Car has had a rear end vibration at speeds of 60 mph+ since I bought it. The vibration seems to lessen when I have a full tank of gas. So...I took it to my Lexus dealer. They put it on the lift and showed me how the two rear tires appeared to be slightly out of round and said that was probably the culprit.
I then bought winter tires and put them on. Still had a vibration. Was told to wait until I put all season tires on, then they'd start to pursue.
I put Pirelli P7s on yesterday. Seem like a great tire, but I'm still feeling a rear end vibration. All 4 wheels were road force balanced. I will be taking my car back to my Lexus dealer to see if they can diagnose. What are causes of rear end vibration. Wheels are not bent, BTW.
View 14 Replies
I have a weird vibration only at freeway speeds. It's a vibration that lasts 3 seconds but are consistently 2-3 seconds apart. It's a very suttle vibration and can be felt at my feet and slightly on the wheel. My passengers can feel it if I mention it. The key thing about the vibration it's starts and goes away the starts and goes away?
View 14 Replies
I just bought a 2008 LS600 Obsidian with Exec package. Happy with the car except for some steering vibration at low speeds when turning. Took it to Newport Lexus...they say..."normal for an AWD LS600".
View 11 Replies
Since I got my car back from the dealership after changing the rear shock this summer, I can feel a vibration in the car at highway speed. After the shock were replaced the car steering wheel was out of balance and pulling one side. After they attempt to align the car about 5 times it got a little bit better. Then I found out that they had an accident with my car and tried to hide it: [URL] ....
I suspect the tie rod may have been damaged so that could explain the steering issue. It also seems to have gotten worse over time. I'm trying to figure out the possible cause, if directly related to the tie rod damage or indirectly as if the tie rod damage could have caused uneven tire wear and then causing the vibration over time. I've attached some pictures, the 2 first are from the front passenger side, the 2 last from the front driver side. My tire are the Michelin pilot and this thread seems to suggest those tire might be hard to align properly: [URL] ....
I'm due for my winter tire change soon and see if thing gets better, I'll get them balanced too. I'll check at the same time for control arms/shock damage. But still, I would like some feedback and see if those tread wear are normal and hopefully get to the root of the problem (the outer edge on the tire in the back are much less damaged).
View 1 Replies
I'm new to Lexus ownership and have recently purchased an 08 certified LS 460 L with the air ride suspension. It's a phenomenal car, I'm now a convert to the brand. One small thing I noticed though is a slight jiggle or vibration coming to the steering wheel at moderate speeds. It is very dependent on the road surface, Seems to dissipate on the highway. Alignment was checked before delivery and feels fine and the tires themselves feel balanced. It's not upsetting, I'm just curious if this is something normal to the air ride suspension. Other than this the car is an absolute gem with only 35,000 miles.
View 4 Replies
For a while I had been having vibration at between 60-80mph I think I mentioned it in a thread before too. Well anyway when I got my 30,000 mi check up they told me it was probably due to the tires being unbalanced and that my tires were in such bad shape that balancing them woudln't make a difference. So I got to new tires (and my rims as you all remember) from NTB. I took it back to Toyota to get the alignment done after that I got on the highway to see if it was vibrating still and it was so they told me to bring back in.
So today they told me one of the tires that I got at NTB was bad because they couldn't get it balance within the range of the other 3 tires so I took the car back to NTB got into it with the guy there and they eventually saw things my way and put a new tire on the car. So after that I get back on the high way the car starts vibrating right when it hits 60. So I take back to Toyota, the guy tells, I heard him mention to one of the mechanics that it might be a bad axle.
Around 6:30 or so they call me and tell me they are going to take rims and tires off a brand new Camry and put them on my car and the manager who lives far away is going to drive my car home and then back again in the morning to get a better idea of the problem with the car. And to top that off they wanted to charge me 40 bucks for a rental car, but luckily I can drive my dad's Cam to work.
View 14 Replies
On my 09' passat wagon 2.0t: I've been on a couple of long highway runs and noticed that my steering wheel is vibrating slightly at higher speeds. Naturally I went for a wheel balance. They showed me one rim was slightly bent from a pot hole or something, but they were able to balance it and put it in the rear. Still a vibration. Took it back to the tire shop and they checked the balance again.
At this point I was still noticing the vibration and went so far as to swap the "damaged" wheel with another off of a passat with the same wheels. No difference noticed. Is it my imagination or is the steering so light in these passats that im feeling every imperfection of the road? I don't remember the car always feeling like this. I am at 14k miles and have the crappy stock good year tires.
View 23 Replies
for the last several weeks, I've noticed a problem that seems to be getting progressively worse... there is a vibration seemingly from the front end (possibly passenger side), and it only appears on the interstate at typical highway speeds (70-75 MPH). facts:
1. It does not happen below ~70 mph.
2. It doesn't appear to be a wheel bearing - no noticeable change in tone or "amplitude" while turning at speed.
3. I use cruise control all the time on the highway, and it is more noticeable going downhill (increases in vibration), when the engine is obviously off-throttle.
4. The car is a 99 V6 5mt.
5. The axles that are presently on the car are Raxles, and have been on it for ~4 1/2 to 5 years.
6. I recently changed over (this past weekend) to my winter/stock wheels and tires, but it was doing it with the summer wheels and tires.
7. It happens regardless if the gears are engaged or not (5th or neutral - I coasted down a hill on the interstate today in neutral to add more info).
8. I've replaced the wheel bearing on the passenger side about 6 weeks ago.
I'm thinking I have an inner CV Joint that is starting to fail. The boots are intact, as I inspected them recently while replacing the clutch/pressure plate/throwout bearing/flywheel. The transmission axle flanges had no play. The vibration was occuring prior to when I changed out the clutch.
Thoughts? Inner CV joint, or...???
View 4 Replies
Driving on the highway the other day and I was doing about 80 and I noticed that the front end started to vibrate pretty loud so I slowed down to around 70 and it stopped. I got home and called up the local tire shop had all my wheels re balanced as I heard that could be the cause they were near perfect. Tires have about 3,000 miles on them. so yesterday I took it out to see if it would do it again and I noticed when it starts to vibrate at about 80 and I push in the clutch it stops immediately. Could my clutch be going out? or possibly like the throw out bearing.
View 10 Replies
I'm having an issue with my wife's 2008 Camry. We're feeling vibration at highway speeds. Feels like it's coming from the front passenger side. We've had all 4 tires replaced (two of them replaced twice because we got lucky and the shop gave us a set of 4 for free with all the trouble we were having with the goodyear tires they sold us), and added hub-centric rings to her wheels. There are no noises to tell me whether it's a cv axle or a bearing. I've been under the car and the only thing I can find that comes close to loose is that the passenger side axle has a just a little more side to side play (runout - inner cv) than the driver's side.
View 11 Replies
My 04 Solara 3.3L vibrates like crazy at highway speeds, but the vibration goes away after a couple of miles, only to return again later, and it isn't a tire balance issue. The vibration comes on quickly, and I have to hold the wheel with both hands, then it slowly diminishes and runs smooth again.
View 4 Replies
I have been feeling a vibration in my right rear at highway speeds (70+mph) At first i thought that maybe it was a wheel bearing but that would constantly be vibration and it wouldn't be off and on like it is. The car is on coils and a friend mentioned to check and make sure my right height is the same all around. I checked just by comparing the fender well gaps and it does seem as if the right rear is a bit lower. If this is the case, can ur car being a little lower on one side cause this vibration? if so, how?
View 2 Replies
Getting some vibration at high speeds on the highway, and when I changed my wheels, I noted that there seems to be some free play in the ball joint on the end. Is this normal? Can I replace just the end of the tie rod?
View 3 Replies
