Passat (B5) :: 2002 - Blinking Check Engine Light And Loss Of Power
Jan 13, 2008
2002 Passat GLS, 1.8T, 98K miles.
Was driving home tonight and nearly didn't make it. A few miles down the road I hit the gas hard going up a hill but the Passat kind of lunged a little and lost a lot of power and the engine emblem starting blinking. Coasted down a hill and it stopped and all was well again. From here on I am going careful up hills and not accelerating too fast.
I drive about 30 miles, 10 miles to go and I have to pull a tall hill. Going up this hill the light starts blinking again and I lose most of my power, engine feels like its not hitting on all cylinders and the turbo must be out. Barely make it home going about 40 mph. My check engine light has been on for quite some time, in fact I have had reset about 6-8 times with replacing sensors, air mass meters, etc. Could this be the timing belt?
View 9 Replies
Advertisement
So I am on my way to the store this morning and the check engine light starts blinking. After I get out of the store I try to start the car so I can drive the mile back home and then have it towed to the dealer. The car is only able to drive at like 1-3mph. I changed the cam follower 6k ago and the car only has 43k.
I'm thinking this seems like a fuel delivery/cam follower type of issue. At the moment my plan is to have AAA tow the car home so I can see if its a follower issue. If it is I think I'm going to have to take off my downpipe and put the stock one back on. When I put the car in neutral and step on the throttle I get no revs at all.
View 4 Replies
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
View 1 Replies
My check engine lights been on forever, like every VW, but now it's blinking fast, and the car isn't running right. It's messed up AGAIN, it's running really bad, like misfiring and not making power. It's shaky feeling in the throttle and power, almost like it's going to stall but it doesn't. What the problem is?
View 5 Replies
My 2002 Windstar SEL has been giving me a fit and I`m not getting any codes as to why. Here`s the 2 main issues. Clicking when i go to start up in a.m. if it`s below 50 degrees. ( Battery has been checked and all is o.k. or so I was informed). As long as it`s warm it starts fine every time. Also,it seems like the least bit of wet on the underside will cause it to spit and sputter and the check engine light will start blinking until it sits and dries for a while. (A very shallow puddle less than 6 inches deep at low speed or even the automatic car wash that sprays the undercarriage).
View 2 Replies
'99 Passat GLS - 79,000 miles - no mods ... Solid Check Engine Light was on for about 2 weeks...last time it was on, it was a fuel cap issue so I took my time with it. Well, all of the sudden on 4/14/03, on my way to work, (less than 5 minutes after starting the car) the car starts to ride hard (like going over grated pavement)...check engine light starts to blink! I pulled over. Eventually the light went back to solid.
Tonight (on 4th ignition sequence since picking up the car this AM) - the solid Check Engine Light came on again.
I had a friend who went through this with a 2000 Passat GLS - different dealer claimed it was the MAF, then the O2 sensors, then....she eventually took it to carmax to unload it.
View 13 Replies
Driving on the highway today and when I started to accelerate fast I noticed my check engine light blinking yellow and also noticed loosing boost I think I can only reach maybe 10-12 psi, I am stage 1 revo and also it was 95 degrees out, what it could be, thinking misfiring? so would that mean new coil pack and spark plugs?
View 15 Replies
Drove fairly fast (160km/hr or 100 miles/hr) then took an exit down a ramp and had to stop at a red light. Noticed all of a sudden that the engine was running bit rougher and then noticed the yellow engine light blinking. I know to turn off the engine immediately when this occurs but then all of a sudden engine light turned off and car was running smooth again.
Car has been reliable for 7 years - proper maintained, synthetic oil, 171000km, timing belt changed, burns very little oil, good torque. Should I have it checked by the dealer (fantastic fair vw dealer)?
View 3 Replies
We have a 2004 Saturn Vue that has been in the shop FOUR times for a loss of power issue. The check engine light will come on and almost simultaneously the loss of power light will come on and the car will pretty much come to a stop. So far they have replaced the computer, gas pedal, wiring to the computer, cat converter...it is still doing it!
View 30 Replies
I changed plugs wires and car started drove 32 miles to work started loosing power fuel pump seems to b fine check engine came on then started flashing worked 10 hours and car won't start 98 Buick v6 3.8....
View 3 Replies
I have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
View 3 Replies
I was driving my 2010 Prius on the Highway (less than 2 miles) and the engine check light came on.... shortly after the ! (triangle with exclamation light came on and then started flashing). I exited the highway and was going back home. On the way home, I noticed a decrease in acceleration and then a message 'Hybrid...'
I was able to coast into an apartment complex and then got a ride home.
After about a couple of hours, I went back to the Apartment Complex. I reviewed the manual and one of the options was to check the gas cap. I filled the tank up last weekend and haven't driven it since today.
View 19 Replies
My girl friends car is doing something interesting, well it started off the car died while she was driving home from work, so I towed it with my truck home, the alternator had went bad so i changed that, but no here is where the problem comes in that i cant figure out, the car will start and run for about 3 miles than it will die in and out, loose power but not kill the engine and the check engine light flashes, and now the radio does not work at all (at idle or running) and the head lights are dim.i tested the battery, it was with in ranges for cold starting, output while the car is on and a few other thing, i re checked my belts and they are all tight and in the correct alignment ...
View 9 Replies
I have a 2004 santa fe with a 2.7 v6. I have had a little misfire issue lately. I had a major power loss with a check engine light on it lasted for just a minute before it settled itself out. Had the code pulled at a local parts store. P0301 so I checked the plugs and they looked worn out. I pulled the upper intake and replaced the plugs and wires plus the upper intake gasket. I cleared the code and that seemed to correct the problem. Two days later, same thing happened. The engine seems to be running fine now. I wiggled the wiring harness to the injector and to the coil, no change in the way it runs. I was thinking it could be an injector or a coil pack.
View 6 Replies
Well I had the dreaded loss of power and EPC/Check Engine light happen on Monday. Was driving down the Interstate and all of sudden we just lost power. It did not go completely dead, but it ran like crap. Called the local VW and they advised to bring it in, still under warranty (27k, 26mths) and it turned out to be the high pressure fuel pump. They replaced the pump and the replacement was bad! Luckily they tested it before they got it out the door back to me. Provided me with a loaner and the dealer had to get a replacement pump overnight. Picked up the car yesterday and everything drives the way it should again.
I had already had the software update, but according to the service advisor that was for the fuel pump in the tank, not the one on the engine. Not sure if that is correct, but that is what the advisor told me..
View 3 Replies
2000 Ranger 2wd 3.0 ... I bought my truck last summer for $1k from my neighbor, it has hit a deer so the grill is busted,front drivers fender bent up and bumper is bent all to heck. The old girl is rock solid reliable though and gets decent mileage with cruise heat and ac so I'm happy.
Anyways on to the point, I am having two big issues with it, the check engine light randomly comes on and causes it lose power sometimes at others you don't notice it. I have not been able to get codes read because it goes off every single time I go to someplace with a scanner. The light will usually go off if you floor it for a long stretch maf maybe?
The other issue is the transmission, I don't know for sure which tranny it is but the overdrive button does not work at all even though the fuses are good and when I drive down the highway second gear you have to let off for it to shift sometimes ( I've been leaning towards the valve body gasket for that) and lately it has started a horrible vibration kicking out of overdrive or just downshifting on hills etc.?
I forgot to mention it has 255k miles on it and I don't know the history besides the balljoint I replaced this week and radiator when I bought it.
View 3 Replies
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
View 2 Replies
I took delivery of my 2012 FX4 Eco in January and about a month or so later I began experiencing a loss of power and the check engine light would come on then go off again. This happened the first time in Houston traffic one day so I was pretty concerned needless to say but then it cleared itself shortly thereafter. However, heading back home it occurred again on the highway while I was trying to pass and she just didn't have the power. I took it to a Houston dealer late in the afternoon before I left but no codes were found and when I got it back to my local dealer it was determined the left side catalytic converter was bad and it was subsequently replaced. Well, it happened again and it's back in the shop while I am offshore so they have plenty of time to take care of it.
View 2 Replies
The engine light in my 2001 Passat all of a sudden started blinking when I started it this afternoon - for no apparent reason. It feels like it's going to stall and is idling kind of loud.
View 3 Replies
Driving while in 4x4 HI up a hill the truck started to slip. I stopped, shifted to neutral, and engaged 4x4 Low. I shifted back to drive and started moving up the hill. The engine started to lose power and the "Service Engine Soon" light began to blink. I put the truck in park. As I let it run a little bit, the engine started to shake as if something was very imbalanced. I went to check under the hood, and confirmed that it was shaking quite noticeably. There was no grinding or clattering of any kind though.
I turned the truck off for a bit, and then restarted. There was no light or shaking upon starting up; but as soon as I put it in gear and started driving I could tell it was losing power, the light came back on, and the shaking ensued. This occurred in 2wd, and both 4wd lo and hi. I parked it at a neighbors place and there it sits for now.
I plan to try and get the codes read. My other vehicles can't make it through the snow we have right now, but it is suppose to get warm later today and might melt enough for me to get one out. I also live out in the country, so the nearest auto parts place is about 20 miles. Same with a dealership service shop. I'm hoping I can buy and return a code reader from an auto parts store to assess if this is something I can diagnose myself or not.
It is the 6.0l gas engine with the 4sp automatic transmission. The truck also has about 107,000 miles.
View 16 Replies
Check engine light came on after a car wash yesterday. I'm sure there is nothing wrong with the car and i recently had an oil change done. i use full synthetic oil too and always get it done on time. Is there a way for me to clear the engine light myself?
View 8 Replies
