After reading some posts I think my passat could have the cam seal and valve cover gasket leaking. I smell burning oil when stopped. How much should this repair cost if I go to an indy repair shop?
View 3 RepliesI've been noticing an oil burning smell after driving recently, it's been going on for a few days now. My oil level is good, I have 8,500 miles on the car. Today I finally had a chance to look under the hood for any visible leaks, and I noticed some oil stains on what I think is the valve cover gasket.
2015 Sonata 2.0T ...
My 2002 1.8 t has a leaky camshaft seal. The shop where I take the care insists that I should take care of it since it can cause some damage to other components. Another very trusted mechanic has told me that it is only a nuisance and the worst thing that can happen is that I would occasionally smell some burning oil inside the car when the HVAC is not in recirculating model. He also suggests using some engine cleaner and degreaser and that would take care of the problem. I think the seal leaks less than a teaspoon a year. The engine uses ZERO oil in between changes.
View 8 RepliesMy son-in-law came by tonight and showed me his ticket from his oil change at the dealer on his '08 Azera, 108k miles. Tech remarked that both valve cover gaskets AND the oil pan gasket were leaking. I've walked through his garage many times when my daughter has the car at work and I've never noticed any oil on the floor. Should have I seen any? I told dealer I would just drive it and monitor the oil level and any other signs of oil leakage. Since he bought the car with 101k miles and a fresh oil change ticket and never checked the level over the next 7k miles I don't think it's leaking bad.
View 2 RepliesA couple of days ago, I was driving my car around when the oil pressure light came on. Having recently changed the oil myself, I figured I had neglected to tighten something down there and it had become loose and was leaking oil. I stopped at two different shops. Both shops told me the leak was coming from the valve cover gasket. Instead of paying $200 for them to replace it, I did it myself. I didn't use any sealant or silicone, or anything like that. The old gasket was hard as a rock and had some sort of red cement around it.
After I had everything back together, I had a partner start the car for me. The oil leak has become much worse--probably a quart a minute. The thing is... I can't see any oil leaking from the valve cover gasket. You would think that an oil leak of that volume would be visible if it were coming from the top of the engine, no? We're going to take the gasket off again to inspect and perhaps use some gasket sealant in select spots, per some YouTube videos we watched.
I'm thinking of purchasing a 2001 GLX VR6 Jetta with lots of deferred maintenance (shocks/struts, brakes, exhaust). Most worryingly, the valve cover gasket is leaking oil. The price is pretty low, but is such a beast worthwhile at any price or is it better parted out? And the interior is about as beat up as the mechanical--screeching passenger window motor, broken glove compartment ... Is this thing worth being brought back to life?
View 6 RepliesI have a 2002 toyota camry xle 6 cyl i believe i have a valve cover gasket leaking vehicle has 112,000 miles. is there a step by step removal proccess i can access. I have done one on a 1995 honda passport 6 cyl how difficult is it
View 2 RepliesMy wife has a 2004 escape v6 (3.0L). The valve cover seal was leaking so I decided, why not change the plugs since I'm already going to have the intake manifold off.
I got down there, replaced the seal (just the front side, didn't want to disassemble something that wasn't broke) and then replaced all 6 plugs and boots (with springs). Fired it up and everything seemed fine. She went to drive to work and the CEL started to flash. I read the code and there were 4 (Don't remember exactly what they were), but it was a combination of things resulting from a misfire in cylinder 4. Since it was one of the front ones. I just pulled the plugged and replaced it hoping I had gotten a dud from the factory. Nope, still doing it.
I didn't take off the fuel lines, just the air intake on the top. I did not change the coils, but everything was running fine before I changed plugs so logic would dictate it is something I did. Only seems to misfire at higher speeds. Also, her battery light randomly comes on, but the battery and alternator test good. This has been happening a while.
I have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 RepliesI have a 99 passat 2.8 v6, that closing on 200k miles, and its a car i'd really like to keep, lately i've had a few leaks coming from valve cover gasket, which i replaced, and now from the front drivers cam, and the rear passenger cam, the smell is terrible and the smoke is worse, i clean out the pcv but its still happening, i talked to a mechanic he says with that many miles i should just do the timing belt and get the seals done.
View 19 RepliesI noticed the oil smell that can be associated with a leaking Cam Tensioner Adjustor Seal from my 2003 1.8T Passat a few months ago. The dealer confirmed that it was leaking and that it was covered by my extended warranty since my car was 5 years old and at 70K miles. I had the work done and after I picked up the car I noticed that the oil level was at the top of the hashes not at the top bend like it was when I took it in.
I don't know what caused it to drop to the hashes but I do know that the level has dropped to 3 visible hashes in the little over 1K that has been put on the car since then. I am concerned because in it's first 70K miles the car did not visibly lose a drop of oil.
Any logical cause for this annoying trend, the only thing that changed was that the Cam Tensioner and Valve Cover Gaskets were replaced. Is it possible something else was messed up during the repair?
I took it to the stealership to get the alternator and some vac. lines replaced all under an extended warranty. They informed me that both valve cover gaskets and right side cam adjuster gaskets are leaking. By no means am I a mechanic or close to but I am trying to get this stuff done as cheap as possible so I am going to try to tackle this myself.
View 3 RepliesSo, weird smell that I thought was burning plastic or rubber is actually hot oil leaking from the valve cover and tensioner gaskets.
My car is nearly 8 years old (2003), and has about 70K. Should I go ahead and buy a timing belt kit and replace all that stuff at the same time?
Last week my check engine light went on. Some hoses needed replacement and the mass air flow sensor was out of spec - I had it replaced as a preventive measure.
Now the car seems to have a subtle oil/exhaust/acrid smell, especially after car has been driven 15 minutes or so and in stop and go situations. When I step outside the car, an acrid smell appears around the engine and tailpipe area.
Check engine light is off - I took it back and they could detect nothing amiss - granted the whole garage smells like oil and exhaust. They did find a "class 1" oil leak on the rear valve cover - just a bit of oil on the rim - not yet dripping.
When stopped at lights I start to smell burning oil coming from the vents when I have the heat on. It only happens every now and then and only when you are stopped at a light. I tried letting the engine idle after driving once and I can't smell it when i open the hood. I do synthetic oil changes every 5,000 since the car was new. I don't know what it could be? My last oil change was about 2,000 miles ago so I can't see it being burn off from the last change still.
View 4 Replieswhen replacing valve cover gasket, using the cork based one. Do you use any gasket sealant or any kind of silicone or just put it in by its self.
View 5 Repliesso I have a 2azfe engine
So there's an oil leak coming from the valve cover gasket (just purchased vehicle dirt cheap with 220k)
found this
Notice all the oil sitting on top of the exhaust mani gasket
In the left(lower) part of the picture it appears to be scraped.
the gasket appears to be newer, I did NOT use a screw driver to remove the valve cover, which is what this appears to have been done..
Can this be sanded down then filled with jb weld, and then regasketed?
So I'll be taking on a project to replace the valve cover gasket on my 2002 Camry V6. There's a bit of leakage through the gasket. And while I'm at it, I'll replace the spark plugs as well. I'm looking for a write up on this project. did a lot of searching but couldn't find anything.
View 14 RepliesI've got a coolant leak here (I wiped away some of it before taking the picture):
Close up
This is the only place I can find coolant leaking and it's running down all the way to the water pump:
When I wiped away from just below the valve cover gasket it flaked right off and it doesn't appear there is any oil mixed in. I changed the oil today and it didn't appear to have any coolant mixed in either.
The coolant doesn't appear to have any oil in it's nice and pink as it should be. I started the car from a cold start and sat and watched the area waiting for it to leak but nothing ever came out, of course.
I know there shouldn't be coolant leaking from this area anyways but I don't know how else to explain the trail pictured. I definitely have a small leak somewhere as I've found coolant on the floor of the garage before.
Do I just replace the valve cover gasket and move on or is there something else I should be concerned with here?
How difficult is it to replace the valve cover gasket on a 2001 Santa Fe with a 2.7? Can I just do the 'front' valve cover? Are there any tutorials with plenty of pictures while doing this?
View 4 RepliesA few days ago I noticed some oil leaking from the left (front) valve cover area and I suspect it's the gasket. Fortunately, I didn't see any leaks from the back cover. It seemed like an easy job to replace the gasket, but as I started to disconnect the wiring, e.g., cam sensor, spark plugs, etc., I can't seem to find a way to remove the black plastic wiring harness 'housing' out of the way.
View 1 Replies