Passat (B6) :: 2006 2.0T - CEL On And Cylinder 3 Misfiring
Jan 25, 2011
My dad has 2006 passat 2.0T. In December 2010 he went overseas. During his absence the car was parked in garage and not in use.
So one day I decided to start the car and as soon as I turned it on the car made this noise and check engine light came on. Took the car to a private repair shop and found out the cylinder #3 was misfiring. The tune up for this car was due so I had all four spark plugs changed and the car ran fine for few days. Then couple of days later it started making the same sound and this time around the coil for cylinder #3 was replaced.
A few days after that check engine light came back and this time it was blinking and the engine was struggling to run, took it again to the workshop yesterday and this time another coil not sure which cylinder was replaced. (all this is done at a private workshop). I have a hunch that the car is going to run fine for a day or so and the problem is going to come back
I never had any major issues with it up until now. Bought this car new in 2006 from dealer. I am afraid that this might be a start of a downhill roll from here on I will drive the car tomorrow and see how it reacts.
View 7 Replies
Advertisement
I've done just about everything me or my mechanic cannot figure out why cylinder #3 is misfiring has new plugs coilpacks checked wires etc. I love this car and will not put it to sleep!!
View 2 Replies
I'm having the absolute worst time trying to fix my wife's 09 accent. We bought the car in '12 with 45k miles on it, and just hit 109k last month. About a year ago, the car started misfiring badly (hot day, after reaching operating temperature) followed by the CEL coming on, and a cylinder cutting out. I (mistakenly) figured coils, and replaced them. This "fix" didn't last more than a couple months.
I've also replaced the intake manifold gasket, suspecting a vacuum issue, due to the symptoms. While doing that, I put in a new PCV valve. To no avail, as the car still misses, chugs and shudders while accelerating at operating temperature. I've disconnected/checked the sensors on the manifold, the 02 sensors, the evap purge solenoid...I absolutely can not wrap my head around this.
The weird part is that the car starts fine when cold, (with only a split-second hesitation if you goose the throttle) and will run great for about 10 minutes/until it warms up. Then,once it warms up it will jerk, shudder and not accelerate at all unless you knife the gas. After letting off the gas, it goes right back to "misfiring" and the light comes back on. I can shut the car off, restart it, and it will run fine until the accelerator is pressed.
View 9 Replies
I have 2006 Subaru Forester that is idling roughly. 90k – oil change every 3k miles. Per diagnostic codes I learned that the 2nd cylinder was misfiring. I replaced the coil, spark plugs, ignition wires, and an airflow sensor. Yet, my car still idles rough. The check engine light is solid and the cruise control is flashing. The idling problem only happens when stopped… after I get high rpms there is no shaking. I had someone disconnect the battery and reset the computer and the lights stayed off for about a week and idling was fine. Week later – the problem returned. I think this an electrical problem, but not sure if mechanical.
View 19 Replies
So my Pacifica, after a long road trip around a year and a half ago, had it's check engine light come on. The meter read P0305, which is cylinder 5 misfire. When I got home, my local trusted mechanic replaced the coil and wire. Since then, the same misfire has occurred at least 4 times, and 3 of which he replaced the same parts (free warranty swap of the parts). The last time, he was determined that it wasn't simply the parts going bad. I concur. It has now lasted roughly a month and the light is back on with the same code. The spans have been as little as a week between leaving the shop and the light coming back on. I personally don't feel the car riding rougher than normal, but my wife does. I don't smell gas, have odd colored exhaust, or any other issue. The only other thing, which idk if it's related, is a clicking noise from the engine, which quickens with revving, perhaps the risers. What else could it be? I read that Chrysler's go to is a valve spring retainer lock and a MAP sensor that accompanies it.
View 19 Replies
I haven't started my passat for the winter and I finally did today. It was ruff start/idling and I pretty sure it was misfiring on one of the cylinders. I turned off the car and start it again...same thing, ruff idling like 3 cylinders were running. I waited five 5 mins and started it again, then it was a normal start on all cylinders. But the engine light came on, even though it started properly. I know I have to clear the code to get rid of the engine light. But I want to avoid any future misfiring. So I'm thinking new spark plug/coil overs.
View 9 Replies
Recently my car, after I put fuel into my car, my car won't start unless I apply the gas and then shift it into gear. I thought that perhaps replacing my spark plugs would fix this problem since it is about time for a tune up on my 2010 Hyundai Accent. About a week after changing the spark plugs I now have an error code that states that Cylinder 2 and 4 are misfiring and it is causing my car to shake while it is idling or speeding up. Also it is much slower than before to get it started from a stopped position.
View 11 Replies
I recently took my 2007 VW Passat 2.0T in b/c the check engine light was on. They initially replaced a leaking valve and a bad ignition coil, but the car was still misfiring on cylinder 3. They took off the intake manifold and found that there was significant carbon build up. The service writer said it was from "low-quality" gas. The car requires 91 octane. I've used 93 octane since 2007 but started using 89 octane around 6 months ago when the gas prices spiked again. Could 6 months of 89 octane cause significant carbon build up to the point it would trip the check engine light? Or could something else have caused it that I need to watch out for?
View 4 Replies
I've been out of town a bunch and my car has been sitting out at the airport. I picked it up last friday, drove it home. Today on my way to work the car started jerking - like the engine was trying to rev slightly. When I put it in park, and listened, the engine was jerking or misfiring maybe. The exhaust was a bit louder than normal as well and i could hear the stress in it. I also smelt a strange burning smell. I've called and had roadside assistance pick it up and take it to the dealer.
View 7 Replies
Happened a few times on me lately. While pulling towards the top of 5th, I'll start to see the check engine light briefly blink as if the car wasn't sure, then at the top of 5th, she'll start misfiring on cyl 2 and 5. It's only during the long haul pulls that this occurs. My plugs and coils were all changed about 1k miles ago.
View 17 Replies
Going up a hill this LS started shuddering and misfiring and set the po302 code. A small push on the accelerator sometimes seems to temporarily remedy the issue. This started about a week ago. fuel mileage : 26 mpg highway
Here's the readings I got at idle:
Fuel pressure is KOEO - 0 (That's what it read.); KOER - 30.
MAF - about 70
LT FUEL TRIM 1 - 5.5
ST FUEL TRIM 1 - STAYS NEGATIVE
LT FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 11 - STAYS NEGATIVE
ST FUEL TRIM 21 - STAYS NEGATIVE
O2 1 - NORMAL FLUCTUATES PROPERLY
O2 S12 - STAYS ABOVE .500
O2 S21 - NORMAL FLUCTUATES PROPERLY
O2 S22 - STAYS ABOVE .500
Not familiar with this vehicle...
View 2 Replies
I have a 2008 Touareg 2, V8, 4.2L.
I bought it used (~95k miles) and almost immediately had an issue. #5 is misfiring. Since then, it has been in the shop 10-12 times with no resolution. Here is what I have done so far:
Put in all new plugs/coils sent the ECU to SIA electronics in Chicago for testing - no errors replaced the injector with a new injector on #5swapped #1 for #5 (plugs/coils)checked the harness (dealership said they did this, but not sure if they did or are just tired of me)
Through all this, #5 is still misfiring. The dealership is out of options, suggesting that the ECU is faulty and needs to be replaced ($1600) or they need to swap the #5 injector with #1 to see if that is the issue (~$1000+). Neither of these options sound reasonable because a) the ECU was already tested and b) the injector is brand new, yet the exact problem (#5 misfire) has persisted before and after the injector replacement.
View 3 Replies
The car already has a cel even though I just bought it. Drove home from work this morning had no problems, went to go shopping no problem, come out start my car and it won't idle right, problem. The Cel flashed at me and once driven a tiny bit stayed constant. Seems like a cylinder is misfiring because of the sound it makes and it is hesitant when you give it some gas. What could it be, coil packs (which is what is was in my 24v) MAF, spark plugs?
View 22 Replies
I just had all 6 fuel injectors changed as they were rusted. But the 4 and 6 are still miss firing. I am going through gas more than I should. I had the EGR replaced as it was stuck open. I do not want to pour more big money into this thing. What can I do. Sea foam is not working. Could it be another problem. I am starting not to trust the mechanics.
View 12 Replies
My 1988 240DL is miss firing #4 cylinder. I cannot get it to fire. this is what I have done:
Swapped plug wires with the #3 wire. Miss fire does not follow the wire
Swapped plugs with #1 plug. Miss fire does not follow the plug
Tested injector power with a tester and it lights up properly
Replaces #4 injector with a new one, still miss fires.
Replaced cap and rotor
Compression test shows 150 LB in #4
sworn and thrown a few tools, still miss fires.
Spark seems good with the plug out and grounded on the block. What else should I test and or try...
View 1 Replies
I have a 2001 golf with a 2.0 AVH engine. I recently replaced the coil-pack and was very pleased that the engine was running better, the only problem was the mpg was still kinda low in the 24-5 range when it used to be 29.
I tried to do a compression test but I didn't prepare properly, I thought you left the coil pack plugged in and the fuel fuse. Now I have a CEL that *was* flashing saying cylinder one is misfiring though it has stopped flashing. I drove it 13 miles home and it did improve but its still running rough. Very reminiscent of when my bad coil pack was still in there, a real lack of power.
So I have to ask, what can I do from here? Have I damaged my coil pack or cylinders? Will this likely go away on its own? Is there anything I should do?
View 4 Replies
I used fuel injector cleaner in two different gas tanks; the car started shaking and the check engine light came on. The mechanic changed a sensor but the car was doing the same; I was told that it will take 4 full gas tanks to clean the gas lines. I went to autozone and they told me that the car had a misfire on cylinder 5 and multiple misfire as well. I do not trust the mechanic any more since I had to take the car back to them several times and still is not fixed. They also did a full tune up and the check engine light still on and flashes when I am going about 55 mph.
View 3 Replies
Changed the spark plugs now I have misfire in cylinders 3 and 6. Do I change the spark plug wires or the coil pack?
View 5 Replies
Had a misfire in cylinder 1 so I put new plugs and wires. Still misfired. Changed fuel injector. Still misfired. Changed ignition coil and misfire on cylinder 1 is gone now cylinder 2 and 3 are misfiring. I double checked wires and they are properly installed.
View 11 Replies
This has been happening intermittently for a while now. The car has about 97k on it and I within the last 1000 miles have replace the timing belt, water pump, coolant temp sensor, tensioners, thermostat, and MAF (OEM BOSCH from ECS).
The car was overheating; all the cooling/timing related stuff was changed, no issues for a few weeks. Then it started misfiring and stalling like a madman in cyls 2 and 3. Ran ran if for the code pulled the MAF and sure enough it looks like the PO never cleaned it as there were probably 2mm of buildup on it; as preventative maintenance I went ahead and just replaced it completely.
Now, less than a week after I replaced the MAF the car will make random little popping noises under hard acceleration, and randomly will just completely stall; without showing the battery or check engine lights, similar to how it was stalling right before the MAF went bad. I live three miles from my office and it has happened going to and from every day for the past two weeks.
As far as I know the car is mostly stock (I purchased in in March). However it does have a knockoff BPV of some sort that I think could be causing the issue as the popping noise sounds like its coming from the passenger side of the car. What this might be (if it's not the BPV).
View 10 Replies
My '04 v6 wagon 100K will misfire in really damp conditions. Last fall after going through a massive puddle and today after sitting for a couple of days of warm damp foggy & rainy New England spring weather. OBDII scanner is reporting cylinder 3 as the one misfiring in the fall, today there were a ton of codes (that I didn't note).
So I made it about 2 miles from the house and had to turn back. No power, check light flashing. I had to put it in manual and keep the revs highish (3-4K). When I got home the exhaust manifold was glowing yellow, assuming one or more cylinders were passing fuel out to the exhaust and it was being burnt off in the manifold.
My question: could I have damaged any gaskets back there? This could be my imagination but I think I'm hearing a new noise that I'd normally attribute to an exhaust leak downstream of the muffler, very subtle - like a gentle light but rapid thud. I only hear this noise with my ear to in the front driver's wheel well. There's no ticking noise I normally attribute to leaks near the manifold. My imagination or is it easy to damage something in the circumstances I describe?
View 11 Replies
