Passat (B6) :: Sputtering And Fault Codes
Apr 6, 2012
Driving home car started sputtering like crazy. vag com'd it and this is what i got from the scan!
Friday,06,April,2012,16:16:02:36785
VCDS Version: Release 11.11.2 (x64)
Data version: 20120126
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: 3C0
Scan: 01 02 03 08 09 0F 15 16 17 19 1C 25 42 44 46 52 53 56 62 72
[Code] ....
View 3 Replies
Advertisement
My V8 is "sputtering" between 1000 - 2000 RPMs. Not only can you feel it, but you can see the tachometer bounce up and down as well. No problems accelerating or putting the engine under load - it's only between that RPM range where there seems to be hesitation. The car is not giving any fault codes, and I just recently had all plugs and coils changed. (The car ran great for 2000 miles following the plug and coil change.) It started on a road trip, and I took it to the local dealer. They thought it was bad gas. (I've since run several tank fulls through it...)
My suspicion is a mass air flow meter beginning to go, but until it triggers a fault, I can't say for sure. The dealer wants to check the MAFs values and to do a fuel tank pressure test to see if it's the fuel pump. I do have the Real Driver warranty, but they will not cover investigative costs. I'm not too excited about throwing money to test a bunch of different things.
View 12 Replies
I have a 2008 MK4 2.0 with only 53,000kms. At 40,000Kms I put new OEM spark plugs.
Just recently, every morning when I start the engine is sputtering and rough running. The engines want to die but I give a little gas, and run rough like it is only firing on two or three cylinders.
When it gets to the normal operating coolant temperature it runs without any problem and I can use the AC. Its only give me this problem on the first start of the day.
Does not have any MIL light on the instrument panel. I scan it with VCDS-Lite and do not found any fault codes. The only thing that's come to my mind is to change the Green Coolant Sensor.
View 3 Replies
Can dealership diagnostic tools read ABS/ASR fault codes, or if those codes are even stored?
View 1 Replies
I have followed the process for clearing and resetting the Steering Assist/ABS fault codes. I have done all the steps several times and cannot get the faults to clear, although the VAG-COM indicates all is green during the testing phase.
[URL].................... And the faults will not clear.
Here is the scan results, (non-fault sections removed):
VAG-COM Version: Release 704.1
Data version: 20070422
Sunday,03,June,2007,17:47:17:25986
Chassis Type: 3C0
Scan: 01 02 03 08 09 0F 15 16 17 19 1C 25 36 42 44 46 47 52 53 55 56 62 65 72 76
[Code] ....
View 7 Replies
I recently sent for a reset my airbag module, yes my car was in a collision, I replaced passenger airbag(only 1 airbag deployed). And reconnected the module. Using the VAG COM, I scanned the airbag module, shows no fault codes, but i still have a light.. now I'm thinking seatbelts and sensors maybe the problem. Where the sensors for a 2005 passat passenger dash airbag are located.
View 2 Replies
I have a 2006 passat and the check engine light came on so I performed a scan, the results are below. fault codes... which ones would need to be repaired immediately?
VCDS Version: Release 805.1
Data version: 20080823
Tuesday,06,March,2012,18:12:35:26365
Chassis Type: 3C0
Scan: 01 02 03 08 09 15 16 17 19 1C 25 42 44 46 52 53 56 62 65 72
VIN: WVWAK73C86P106340 Mileage: 107910km/67052miles
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
[Code] ....
View 6 Replies
Ok in parking lot car is armed but driver side door is unlocked press the unlock on remote will not unlock the doors however I can pop the trunk with remote. Try to start car and alarm is triggered and car will not start. I have fault codes like 00928, 01358. Is there away to disable the entire alarm so I can start it and get home.
View 1 Replies
Ok, so I scanned a 2006 Passat 3.6 4mo. I got a fault for the catalyst system, a fault for the AWD controller, and a fault for the Haldex pump. I'm guessing the catalyst code is for the oxygen sensors? What should be my next course of action on the AWD stuff?
============================================
Address 01: Engine Labels: 03H-906-032-BLV.lbl
Part No SW: 03H 997 033 M HW: Hardware No
Component: P3.6-FSI-LEV2 G00 2370
Revision: --H11--- Serial number: VWZCZ000000000
Coding: 0000175
[Code] ....
View 1 Replies
I have just replaced the abs ecu and have cleared the codes, thought all was gonna be good but now two code are still coming up they are:
01044 Transmission control module - incorrectly coded
00778 Steering angle sensor-G85
View 2 Replies
I have a '99 GT with the 2200 motor. A couple of months ago, it started sputtering around 3000rpm. Over 3600 RPM, runs great. Per my dealer, both cats and o2 sensors were changed. $$$ Did not fix! Local garage found a extremely frayed wire at the crankshaft sensor. There were two EGR codes as well, but were ignored. They changed the wire and the car has ran great for a month. Now it is sputtering again. The garage checked and there are only the same two codes are for EGR issues (I did not write them down). Could it be the EGR? Does it kick in around this RPM?
View 3 Replies
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
View 3 Replies
I have had a wet weather issue twice, once last fall and once this spring. Both times were very wet and damp conditions causing a sputtering and chugging and dying at lights, both times no codes and after drying out in brother's shop it went away. Now this weekend up at the cabin it reappeared, again very wet conditions. Replaced the MAF...no change. Sputtered and chugged my way home with it killing at most stop signs/lights. Finally got home and couldn't even back the TT up the driveway, it would kill. Finally threw numerous codes (misfire in cylinders 1 and 9, and misfire in first 1000 revolutions). I'm thinking COPs as the plugs are not that old and the little research I have had time to do suggests this also. If it is COPs, I have heard there are some to avoid and some that are recommended?
View 9 Replies
2004 Santa Fe 2.7L V6 2WD ... Car was running fine, filled it with gas, and upon starting, heard a backfire into the intake manifold. It coded for a Cylinder 3 misfire so I had plugs and wires changed.
Now...The car starts, idles rough, accelerates sluggishly, and running rough any time it was around 2000 RPM. After I changed the plugs, it started bucking a little and stalls when I take off in the morning.
Coded and it's reading 7 codes, but some are duplicates:
-P0274 Cylinder 5 Injector Control High
-P0305 Cylinder 5 Misfire
-P0102 MAF or VAF A Circuit Low Input
-P0050 H02S Bank 2 Sen 1 Heater Circuit
-P0030 HO2S Bank 1 Sen 1 Heater Circuit
-P0274 Cylinder 5 Injector Control High (Shows Twice)
-P0102 MAF or VAF A Circuit Low Input (Shows Twice)
After having a backfire and then cylinder misfire...replacing the plugs and wires.
View 2 Replies
I have an '05 5.4L 3V and I was way to trusting in how it was running. BTW, I change the oil every 3 to 5 and have only driven highway miles, albeit a lot of them...155k! I bought it with 40k on it but was not aware of the plug change issue until I heard about it off-hand. I let the plug change go cuz it was running so well. Bad move.
Anyways, a few weeks ago it began to lose power and I suspected that the PCM was retarding the timing for some reason. Before I could get to the shop, the thing went nuts on me at 75mph. Started shaking and sputtering and throwing cel codes. I shut it down and after 5 minutes re-started. It seemed fine and actually was running a bit better. Took it in and the code was the 0302. #2 cyl misfire.
They also said the compression was very low on that cylinder and slightly low on 1,3 and 7 as well. I had them change the plugs and the #2 COP even though they said I needed a new engine and then I picked it up. Now the engine barely runs at all. It shakes violently, where to go from here. What should I do now? New engine?
View 14 Replies
So i installed a USP test pipe and got Revo Stage 2 upgrade yesterday. I had no codes before the test pipe. I still have a CEL for 9 fault codes. 4 of which are all the o2 sensor codes. With all these codes my Traction Control light is on too. I think this may be a safety thing. I thought Stage 2 was supposed to get rid of the CEL. Especially for the 02 sensors in the rear.
View 6 Replies
I coded a few things through VCDS (fogs as DRLs, turned up XDS, enabled TSC, etc.) and now I'm getting fault codes from ABS...
I did an autoscan before I started and there were no fault codes before.
View 8 Replies
These warning lights are lit but my code reader (Actron CP9180) shows 'pass' meaning no fault codes. I had a similar thing happen about a year ago Before I had my own reader) and the cause was a faulty speed sensor on one wheel. Since then all 4 hubs have been replaced. Does this sound like the brake module?
View 14 Replies
I was told that these are affiliated to a problem with the air pump (not the one you pump the tire up with) -- Need to locate the air pump? Hoping to find a loose hose or something I can fix.
View 12 Replies
All seems to be going well, drove the car for first 200 meters yesterday! Replacing the faulty parts is always easiest, just need to know if there are any shortcuts for fixing this. What's the engine oil temperature sensor? The one bolted in oil pan?
The intake air temperature is showing -40 degrees celsius.
MAF is plugged correctly.
VAG-COM gives me these following codes:
3 Faults Found:
000406 - Engine Oil Temp. Sensor (G8)
P0196 - 004 - Implausible Signal - Intermittent
000275 - Intake Air Temp. Sensor (G42)
P0113 - 002 - Signal too High - Intermittent
000258 - Mass Air Flow Sensor (G70)
P0102 - 002 - Signal too Low
Readiness: 0000 0000
View 7 Replies
As far as trouble shooting faults in the ABS - does it store fault codes and how can they be read ?
Daughter's 2007 Elantra has ABS symbol lit for a week, I took it to a car wash and used the high pressure spray to clean the wheel hub areas and that may have fixed the problem but interested if ABS fault codes are stored and can be read.
View 1 Replies
