2002 Santa Fe has Shimmy when applying brakes. Had tire balanced and rotated-no change. New brakes with life time pads one year ago. Rotors were turned. Should I replace the rotors and pads or just rotors? Am I on the right track for repairs?
View 2 RepliesI have a Santa Fe 2010 2.4 awd 6AT with 20000km, I live in Ushuaia, Argentina, here the use of salt is normal in winter (a lot of salt). I have one winter and the second is coming with this SUV. Today I was in a road at 120km/h (75mph) and I had to apply brakes. In that moment I noted a little vibration on the steering wheel. After release brake pedal, the vibration disappeared. I checked again with same results, is been posible that my brake discs could be damaged or something is wrong with the brake system? I didn't have any light of malfunction. What is the normal life of brakes discs and pads in a santa fe with normal use?
View 13 RepliesJust got a new to me 02 Limited v8 - 128k on the clock
Noticed today while at a stop light that when I depress the brake pedal (after being stopped) it makes a squishy sound - the pedal feels different, but I don't know if spongy/squishy is the right way to describe it, it just sounds like you stepped on a waterlogged sponge.
Now the brakes definitely don't feel as good as my XLT brakes (recently replaced it due to rod knock - 02 XLT v6). It still stops but seems like it requires more effort and almost fades a little. I initially chalked up the difference in performance to me putting new rotors/pads on the XLT - Thermo-quiet semi's with Raybestos rotors.
However it appears after some brief reading this could be the master cylinder on its way out....is that accurate? I planned on taking my pads/rotors off the XLT before I ship it to the junkyard (less than 3k on that setup), but if its the master cylinder, I'd like to do that while I'm doing all my other tune up stuff this weekend
I'm gonna put it on the lift this weekend and see if there's any brake fluid stains to see if air is getting into the system, but looking at the reservoir over the past week I haven't noticed really any decline in fluid level.
I have a 2002 Honda Civic EX 1.7L. Recently the brake pedal would sometimes go to the floor when I'd apply the brakes. The car would still stop, but not as quickly as normally. If I apply the brake and it goes to the floor I would release the pedal and reapply the brake and it would stop at it's normal position and the brakes felt firm and the car would stop fine. I was told my problem was the master cylinder so I bought one on Sunday and replaced it. I bled the lines and it seemed like all the air was out. The brakes worked great and the pedal stopped in the same place and was firm.
Now today on my way to work the pedal went down a little farther than normal during one stop. On the way home it stopped in different places. The brakes would always grab and the pedal felt fairly firm wherever it stopped. I drove it this evening again and the pedal went to the floor like with the old master cylinder. One pump and they grabbed in the normal spot. What is going on? Did I not bleed the lines well enough? Is the new master cylinder just junk? I saw in the manual that air can get trapped in the ABS sensor, but an air bubble problem should just make the pedal squishy, not change where it grabs, right? I'm stumped and I really don't want to take my car in if I can fix it.
I have a 2007 Sante Fe Limited that has 93k on it. Within the last year I have noticed the steering wheel will shimmy when you apply the brakes at high speeds, it's slowly came to the point now that anything above 40mph will cause the steering wheel to shake while applying the brakes. I am guessing I have warped or unevenly worn front rotors. The car supposedly had a break job done at 74k and this started happening at about the 90k mark.
I was looking at these : Front Performance Brake Rotors Posi Quiet Ceramic Pads for Santa FE 07 09
Second question, any tool list or required sockets sizes to complete a front rotor and pad replacement? I have a floor jack, jack stands, a set of 3/8 deep metric sockets. I also have a breaker bar. This is my only car so I want to make sure I have everything I need before I start taking stuff apart.
'05 Santa Fe 2WD 3.5. Front end shimmy at about 70 mph. bad CV joint. I am replacing both left and right. Got everything out of the way to remove both CV's. Problem: The retaining ring at the end of the axle shaft will NOT release the axle. Pry bar not having any affect.
View 1 Replies'05 Santa Fe 2WD 3.5. Front end shimmy at about 70 mph. bad CV joint. I am replacing both left and right. Got everything out of the way to remove both CV's. Problem: The retaining ring at the end of the axle shaft will NOT release the axle. Pry bar not having any affect.
View 1 RepliesI am getting a drone like sound when driving at any speed only when applying the gas, is this normal if not what would be the problem here.. I drive a 2.7 Litre / 2006 Santa Fe.
View 7 Replies2001 F150--V8-4.6-3.55--8.8. 221000 Miles. Changed front rotors and pads. Had scrubbing noise from right rear when applying breaks heavily. Changed rear rotors and pads. Still have scrubbing noise when breaking hard. I do not hear any noise when driving regular or when normal breaking. Differential fluid was a tad low. Applied fluid. Still have scrubbing noise. No leaks at hub seal or pinion. Bearings ? Maybe?
View 5 RepliesI have a 2003 Camry LE 4cly. Approx 150k miles. Car has been a good Camry. About 6 months ago it started to shudder when applying brakes. At first I thought rotors, but it seemed speed dependent. When over 40 it happens more often and more strongly. After the car gets below 10 to 20 the shudder ceases. Front pads are in reasonable shape. Rotating tires does not affect the shudder. Has never effected handling of vehicle. Brakes work without fail, just shudder in front end and steering wheel. I tried flushing the system, had not done that previously. Fluid was yellow, but not black. After the flush, the system seemed to shudder less, but still have the intermittent shudder. There are no error code for ABS, and the light is not on and does not come on.
View 5 RepliesSo having done a single track day, I feel like my rotors must have warped, as there is now a slight vibration when applying the brakes. This is very surprising as I don't do anything out of the ordinary, and tried to use brakes intelligently, including a proper cool down lap and so on. Is this normal? What are my options for making life better? Is there some set of rotors I should get that wouldn't be prone to warping like this? Is it a question of pads?
View 18 Replies1998 base model, 3.1, about 232,000 miles on it.
purchased at about 45,000 miles and always had a slight "hissing " noise when I apply the brake.
Yesterday the car was parked on a very slight incline. Emergency brake was applied. a/c was on . I returned about 5 minutes later and heard a "hissing" type of sound. It seemed to be coming from under the dash on drivers side.
As I put my foot on the brake and shifted into reverse the noise stopped. Today at various times I have the same noise.
I've owned at least 40 cars in the last 50 years and this car has the very worse brakes of all . I've tried all types of pads, etc. The rear cylinders rebuilt about 150,000 miles ago. Master cylinder is original.
I had been hearing bang noise from my front suspension at certain times like when reversing car and applying brakes. It was happening since I bought my car and every time I have complained about it to local VW service guys, I was told by them that they cannot replicate the noise so there is nothing wrong. I even told them to have a look at front suspension bushings but again they said everything is fine.
Last week I went for 45.000KM Service and I complained about the same issue again and luckily this time service advisor heard the noise himself. Next day, they called me to inform that my front lower arm bushings needs to be replaced, front brake pads and discs, and front wheel bearings as well. In my response I told them that bushings were bad for long time and no one figured it out earlier and due to this my front brake discs had abnormal wear along with the wheel bearings.
I am still trying to relate that it is technically possible for brake discs at least to wear off earlier if the suspension bushings are bad as when you apply brakes, the brake discs are stressed heavily as the bushing are not absorbing any stress.
I would like to have thoughts on this matter. Just let me know if my understanding is correct or it does not makes any sense and technically would not be proved.
Just to let you know that it is 3.2 4motion model. My driving is average within 120 KM speed and never hit any potholes etc. Plus my brake pads indicator never went on.
I haven't noticed it before but applying the brakes after driving thru snow I get an awful crunch sound. I have stopped the car a few times to look and it appears the wheel wells are clogged with slush but I don't know if that's whats causing it. After the crunching sound if I'm driving on a clear road there is no noise if I brake. Its much worse than say the crunch you get if the brakes are wet. Whats up with this?
View 3 RepliesI have a 98 chevy tahoe and the truck seems to make a strange noise sometimes when applying the brakes. I can feel (sorta) the noise in the brake pedal. Is this something that needs a scan to find out where it's coming from?
View 11 RepliesJust got the Tiguan SE- love it! We have had it for about 3 weeks. I noticed sometimes while applying the brakes, the RPM's will go up as I am slowing down. I know the car has to move between gears when slowing down or speeding up, but it almost as if it gets "stuck" in a gear when the car is slowing down. Any thoughts, input? We don't drive fast, we apply the brakes and gas slowly to ease the car in. This just seems odd as my past car (2005 Maza 3) did not do this. I am new the VW family so maybe I am just not used this.
View 6 Replies2014 Passat... I've got a little over 2,000 miles on mine now and I really do like the car. However, one thing that is really bothersome to me is----the brakes.
I'm not sure if it is specific to my car or to the passat in general. Here's the issue:
When applying the brakes, the pedal feels almost loose, as though the is no pressure on it, but once you push the pedal down far enough the brakes come on heavy, hard and fast. It's like turning on a light switch.
I am wondering if this is an adjustment that I can have done at the dealer to put more feel into the brakes or if this is just something that we all have to live with, of if maybe there could be something wrong with the brakes on my car.
Have read through alot of the threads and can't seem to find an answer. Bought a used 94 explorer xlt. It came with brand new Wrangler tires. The day we bought it we were driving home and it started shaking and wobbling at about 95kms and but seemed to improve after 115. So I took it to the tire shop next day and had all 4 tires rebalanced. The shop told me that all were out to lunch. The worst was 2 ounces out. Ok cool. Was certain that was the problem. Took off. Got on the highway and same damn thing. The steering seems very tight. No bangs. No knocks. Just the bloody shaking. Oh and also the abs light comes on just as it starts to shake.
View 1 RepliesMy 2000 excursion (94K) front end shimmies when I put on the brakes...could my rotors be warped...or is there something worn in the front end?
View 11 RepliesI have noticed brake groaning sounds ocassionally when applying the brakes. When this happens the pedal seems spongy takes longer to stop. After the car is turned off in the garage I have heard the same kinds of sound coming from the car. It almost sounds like the car in sequencing through checks after the system has been turned off.
View 7 Replies02-F150-4.2L-102k. Truck was rolling down the road at approx. 35 to 40 mph. A speed bump/table appeared out of nowhere and was hit before beeing seen. Immediately since this event, the truck pulls to the left while applying the brakes. It pulls very hard and is fine while rolling down the road. Is there some damaged steering component or did one of the calipers go out from the jolt?
View 4 Replies