While driving the other day the automatic transmission in my 2003 Santa Fe slipped into neutral. I pushed the car home wherre it currently sits. I checked for error codes and found none. There is a grinding noise when I shift from any gear into park.
View 1 RepliesI have a 2002 santa fe v6 all AWD. It has already had a used trans installed about 3 years ago. Just the other day the front main seal in the trans starts pouring. I took it to a transmission guy it cost me about 600 to have one put in it, he said that was the the problem he got it fixed he drove it and it was all good. Get in it driving it home and everything goes fine. Then after about 5 or 6 miles the trans goes crazy, so I am wondering whats up. I get out and look and its out of fluid because the seal done blew back out. I call him he said he fixed it not his problem it worked when it left his shop.S o my question is what would make the seal need replaced again 5 miles down the road is it a torque converter problem, or something in the trans bad, or did the guy just not do it right. He told me to bring it back and he would look at it but I've done spent all i had on it for him to fix it.
View 2 RepliesI just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 RepliesYesterday my transmission slipped as I accelerated from a stop off the highway exit ramp. It grabbed almost immediately and no problems till I got to my destination about 2 miles down the road.......fluid was dripping from the underneath the engine......reddish/pink fluid. Engine was not over heated (according to the gauge). Pulled car off driveway and down the road a bit and transmission was really slipping when trying to accelerate quickly (no issue with slow acceleration). Checked transmission fluid and it was not covering the stick. I thought maybe I burst a transmission coolant line but upon inspection no fluid on that.
So I added 1 quart of transmission fluid this morning and started the car to hope to find the leak. No immediate leaking the transmission case, seals or lines. But I did notice that when I started the car the coolant reservoir was "bubbling". After about 5 minutes to allow the engine to warm and the coolant gauge to come to normal operating range I noticed coolant reservoir/overfill spewing out a pinkish foamy fluid and then checking the transmission fluid level it was drained again (no fluid on stick when running). One last fact....the fluid temp coming from the overflow was cold, so was the radiator fluid after I popped off the radiator cap.....but the dashboard temperature coolant gauge was at the mid point/normal operating temperature of the scale.
So my question is......where do I take the car to have it looked at......a transmission shop, or a typical full service mechanic? Is the transmission fluid co-mingling with the coolant fluid and if so how does that happen?
My wife's 2004 V6 Camry is not happy. As you accelerate from a stop, the automatic transmission will go from first gear to second, and then sometimes just drop spontaneously into neutral. Because you are in the process of accelerating, the engine RPMs increase until you take your foot of the pedal. In the short trip to the dealership for testing, the problem seemed to reset itself when the car was fully stopped. Other times it just reengaged with the transmission on its own without stopping.
Each time the transmission disengages, another strange thing happens--the instrument panel goes bonkers. The speedometer needle drops to zero, but the tach keeps working. The ABS, check engine, and brake lights turn on.
The dealership had the car for several days and has only been able to scan codes indicating the ABS system and the rear wheel speed sensors. I'm skeptical--especially since the repair estimate is nearly $4,000! I'm taking the car to an independent shop tomorrow for a second opinion.
I can follow up with more details from the dealership's diagnostic report, but for now, all I can say is that the car has almost 100,000 miles and we haven't had a bit of trouble with it until now. I replaced the transmission fluid about 10,000 miles ago.
So I drive a 79' f-150 and my truck when I take left turns, start on a steeper incline or give it too much gas my automatic transmission tries to jump from drive to neutral. This only happens initially; if I'm on the free way and at a higher rate of speed it doesn't do this but it seems like when I give it any more than a little gas it tries to jump into neutral (it has once) it doesn't or hasn't really done this on right turns I don't know if that makes sense or not.
Why it may be doing this and if so what I might be able to do about it? I do have a book for my truck and I have done some small things but I don't really know a whole lot.
I bought it for cheap. not shure what tranny is in it. So when you you put it in od it will take off and shift fine all the way to od. getting going and drive it a few miles and it will slip out of od into to neutral. I can put it in drive and it does fine. I did lose all forward gears earlier tonight though. First time it did this. OD is the only gear it slips out of. it willl re engage below 40 mph. But I usually just shift to drive and go on.
View 12 RepliesDriving car auto slips into neutral, car keeps revving until stopped lever put in neutral then into gear drive off again. Thats mothers version of what happens. This happens once a week for last six..
View 2 RepliesWhen taking off the 1-2 shift and the 2-3 shift the truck will go into a neutral state for 2-5 seconds. when this occurs, the rpms will rev since your foot is on the accelerator. Once you let off the accelerator the rpms come down and the gear will catch. I have had the truck in the shop a few times without any luck. part of the problem is no codes are thrown so the dealer has no clue what to look for. This is extremely dangerous when in my case i pull out on a 6 lane hwy with 55mph speed limit. Ford more or less said to pound salt until a code is thrown or until something else happens. this nearly caused a nasty wreck 2 weeks ago.
View 14 RepliesI had a strange problem tonight, my car wouldn't start in park as it normally does, but did start in neutral? I certainly don't want it NOT to start! is there some sort of sensor that tells the car its in park and therefore allows it to start, which may have slipped/become faulty telling the car its safe to start, even though its in neutral and not park?
View 4 RepliesI bought this santa fe for parts for my other identical santa. When you take it out of park into r everse drive 1st 2nd gear it will idle down 200 rpm. It had no codes till I revved it up and moved gears. Codes trans module shift selonoid b and c. It makes no noise or vibration. The torque converter does not grab what so ever if it is even moving. I want to fix it now that I see its better condition.
View 1 RepliesI have a 2008 petrol Santa Fe with an automatic transmission. Recently the transmission started to intermittently make a noise like a buzz. The noise most commonly occurs when first moving off in D or R and always stops when the transmission is put in Park.
View 8 RepliesMy 2001 Hyundai Santa Fe has recently started idling very high when put in park or neutral. While in drive the engine idles above 1K and you need to keep your foot on the brake to keep from moving forward. If you shut down the vehicle while idling high, the car will not start right away. It needs to cool down for 10 -15 minutes before restarting. It will run fine for awhile but will go back to revving up again.
View 7 RepliesI'm having trouble diagnosing a high RPM in park and neutral on my 2004 Santa FE 4WD 2.7L. Idle's great in drive and reverse. Occasionally when I start the car up it will shoot up to 3000 RPM until I shift into drive or reverse with a heavy thunk. Then it drives fine. When I shift back into park when I'm done driving, it will shoot back up. To avoid this, I just shut the car off in drive and then shift to park.The weird thing is, sometimes it doesn't happen at all. Sometimes it starts right up and shuts down with perfect idle. However, once I give it some throttle in park in these instances, the idle will jump back and forth between 1500 and 2000 and won't die back down to 800 where it should be until I shift into drive or reverse. Not sure what's going on.
I've replaced the idle air control valve, purge valve solenoid, and camshaft position sensor, but to no avail. I also replaced the throttle position sensor a few weeks ago, but that didn't seem to do anything, so I took it back. I'm wondering if I maybe didn't do the correct installation procedure. I still have the old grey TPS for what it's worth. Should I change this? I've also played with the tension in the throttle cable, but I don't really know how to get it exactly within specifications. I definitely removed some slack. I just checked for vacuum leaks using the cigar method with a hose from the PCV valve with the throttle body sealed with saran wrap, but I couldn't find anything. My method was shoddy, and I don't really know what I'm doing, so I wouldn't rule out a vacuum leak by any means.
95 Ford Escort 1.9L, 330,000 miles. Never changed the clutch and i bought it with 80k on it. With that said the clutch never slipped and a lot of this is highway mileage so i never saw a reason to change the clutch just because.
Last week i pulled into the driveway i depressed the clutch pedal as i normally do and as i slowed, the car bucked like it was still in gear and didn't recognize the clutch was depressed. When it started bucking i tried to pull the gear shifter to neutral but it wouldn't move, the car finally died in it's parking spot. I quickly popped the hood and had my son press the clutch in and out and all components seemed to be moving fine, i was mainly looking at the slave cylinder assuming since it's a hydraulic clutch if it was a hydraulic issue that wouldn't move if i didn't have hydraulic pressure.
No obvious leaks were noted, i looked at the master cylinder and it seemed a little low but not empty maybe just above min. I filled it to max and still no change. So i assumed it was the clutch finally disintegrated and locked up. Yesterday i got in the car to attempt to move it to the garage to work on it. It started up fine, shifted through all gears with no issue's, drove it around for about 15minutes shifting a lot and pressing the clutch randomly and it worked fine.
I brought it back home and tried to kill it a few more times before i got it to the garage, it finally locked again but it was in neutral and i couldn't get into any gear. Turned the car off and then restarted and it shifted into gear, i pulled it into the garage and stopped with no other issue's.
Checked closer for leaks, between master and slave and couldn't find any. Pulled speedo cable and checked trans fluid, its brownish red (more brownish) and thin but didn't really smell burnt and it is at the correct level. Linkage has some slop in it but i don't see it binding anywhere, i layed under the car and was able to move linkage in/out of gear with my hand. It's easy enough to say the clutch is well over due for changing but since there were no signs of a failing clutch when i drove it i think i need to look elsewhere.
Could it be worn fluid? Could it be debris in the line? Or could it be that the fork just isn't engaging or disengaging properly due to wear?
My automatic transmission slipped today. Really worried now. 2011 elantra with 36k on it. It was raining and I was turning right out of a shopping center. I floored it to beat the incoming traffic and the tranny slipped. It hasn't slipped since then and has been perfect so I know the dealer will say they can't replicate the problem. Should I be worried about this?
View 15 RepliesI have a 2005 Elantra GT hatchback that I love with a 5 speed transmission. Lately every time I'm in 2nd gear, the transmission will pop out of 2nd into neutral. This only happens in 2nd gear. I heard it could be the shift collar (i.e. teeth?) that aren't grabbing in that gear.
View 5 RepliesI have a '05 santa fe, auto, 2.7L, 4WD...sometimes I have to jiggle the shifter to get the engine to crank...would this be the neutral safety switch? or is there something in the shifter housing that could be causing this?
Maybe a minor adjustment... Just a slight movement of the shifter and it fires right up... If it is the neutral safety switch..where is it located? on the trans?
Quick question. I have a 1992 Ford E-350 Box Truck and during a recent highway trip the transmission slipped and I lost Drive (3rd). The van drives fine in 1st, 2nd, reverse, and overdrive. When it's in D, it wont move at all from a stop. I'm able to get it in to overdrive by starting in 2nd, accelerating to about 35mph, then shifting it in to D. If I accelerate enough after shifting to D, I can usually get it to shift in to OD. The fluid is full and clean.
View 1 RepliesThe other day I noticed the car slipped into reverse fairly hard, then when I placed it into drive it also slipped in fairly hard. Once I was out on the road it hesitated and then slipped into gear 3rd then 4th, and when I slowed down it seem to hesitate when gearing down. Two days passed and no problems, then today started up again, and now the "check engine" light came on...! Shifted ok on the way home this evening but check engine light still on. Only 34K, 2012 bought in June 2011. Has been an absolutely brilliant ride up until this week. I understand the tranny is sealed ? Any tips besides taking it to a dealer ? Problem is I live quite a ways from one, and finding the time.
View 14 RepliesI was out driving in my 2003 F150. The transmission Slipped on a shift. I noticed the OD light is blinking. Transmission went into OD and drove fine. Pulled codes P0713 and P0712 transmission fluid temperature sensor. Made it home. An hour later tried to back out and now sounds like a grinding or rubbing sound. But it sounds like the sound is coming from the rear end. I am lost.
2003 F150 4.6L SuperCab....